求任意腐蚀损伤的T-H曲线

给出一种在腐蚀日历寿命计算中,任意腐蚀损伤的 T-H曲线的求解方法。该方法求解独特,制作简便,经济适用,只要有 3条以上的标准腐蚀损伤T-H曲线,就可导出任意腐蚀损伤的T-H曲线,供金属日历寿命预测使用。     

褶皱对碳纤维复合材料层合板压缩性能的影响

为研究纤维褶皱对碳纤维复合材料层合板压缩性能的影响,参考ASTM D6641—2014完成了含纤维褶皱碳纤维层合板压缩性能试验;同时采用基于Hashin失效准则及性能逐渐退化的渐进损伤方法进行了有限元分析。结果表明：褶皱程度为30%的凹陷试验件压缩极限载荷相比完好试验件降低了58.48%;同等褶皱程度下凹陷试验件比凸起试验件抗压强度更低;褶皱程度为30%的凹陷试验件刚度相比完好试验件降低了35.80%;有限元分析结果与试验吻合良好,试验件的损伤最初为基体损伤,经过扩展导致试验件在褶皱处断裂。     

含边界和损伤因素的纺织复合材料细观胞元模型

纺织复合材料的细观力学分析通常以胞元模型为基础,胞元边界条件的合理施加是获得精确分析结果的关键之一。本文以平面机织复合材料为例,讨论了细观胞元的选取和周期边界条件的施加方法,在此基础上建立了二维细观有限元模型,通过与全厚度模型分析结果的比较,研究了周期胞元模型的合理性,特别是边界效应和局部损伤等非周期因素对分析结果的影响,给出了这些因素下胞元边界条件的处理方法。     

Investigation on the interface damage in drilling low-stiffness CFRP/Ti stacks

Carbon fiber reinforced plastic and titanium alloy (CFRP/Ti) stacks have been widely used as aerospace structures because of their excellent combination of physical properties. Interface damage caused by interface gaps, significantly different from that of metal/metal stacks, is a common problem in the through-hole drilling of CFRP/Ti stacks with low stiffness. In this study, a force–deformation coupling model was developed to further examine the formation mechanism and the control method of interface damage. Firstly, the coupling model was built considering the interaction between the thrust force and the deformation. To solve this model, a numerical method was proposed in which specific cutting coefficients were calibrated using only the thrust force of rigid stacks. Secondly, drilling experiments were performed with different feed rates and bending stiffness. Experimental results indicate that interface damage mainly includes interlayer chips and surface damage of CFRP layers. The surface damage, which is irreparable, is caused by the rotary extension of metal chips along the interlayer gap. Thirdly, variations of the interface gap were calculated with the coupling model that had been verified by measured thrust forces. The damage area was found to have a linear dependence relation with the interlayer gap. However, in conditions of large gap sizes, the interface damage areas increased with the interlayer gap at high feed rates, while decreasing slightly at low feed rates. This phenomenon was satisfactorily explained by the presented model. Finally, a method was proposed to determine the appropriate pressure exceeding which no interlayer damage will occur. Additional drilling experiments proved the method effective. This study leads to further understanding of the forming mechanism of interlayer damage and of selecting appropriate parameters in drilling low-stiffness composite/metal stacks.     

Thermo-mechanical properties of RTM-made carbon fibre/polyimide composite attaching collar under transient heating

This study focuses on the thermo-mechanical properties of Carbon Fibre/Polyimide Composite (CFPC) attaching collars under transient heating. The CFPC attaching collars were fabricated by a high-temperature resin transfer moulding process, and their thermo-mechanical properties under the conditions of simultaneous transient heating and bending load were investigated. The results show that the attaching collar tends to fail at 118% of the limit load. The failure mode includes the fracture of the connecting screws, local extrusion damage of the hole edges, and slight ablation damage at the outer plies. And there is no observable residual deformation in the composite attaching collar. Furthermore, considering that the material properties vary with temperature, a progressive damage model based on the sequential thermo-mechanical coupling method was established to study the failure mechanism of the attaching collar. Finally, the damage factor of the CFPC was calculated to assess the safety status of the attaching collar. The results show that the primary damage modes of the composite attaching collar are intralaminar failure, which mainly occurs at the heat insulation layer and the hole edges, and these slightly affect the structural bearing capacity. A good correlation between the experiment and FEA is obtained. The test methods and analysis models proposed contribute to the safety assessment of composite structures under transient heating.     

浅析检查方法的选择对维修成本的影响

维修工作贯穿于飞机的整个生命周期,产生高额的维修成本,如何降低维修成本是航空公司面临的一个重要课题。本文从检查方法和损伤容限概念的角度出发,详细阐述了在保证飞机安全的前提下,如何降低飞机维修成本。     

不同喷铝参数对复合材料雷击防护性能模拟

为了研究复合材料不同的雷击防护(lightning strike protection,LSP)系统在雷电流作用下的损伤规律,对雷击损伤过程和烧蚀机理进行分析,建立复合材料层合板雷击防护的能量平衡数学模型。在此基础上,在ABAQUS中建立复合材料基准件、全喷铝和局部喷铝防护系统的碳纤维增强复合材料(carbon fiber reinforced polymer,CFRP)层合板电-热耦合有限元模型,和实验结果对比验证模型的有效性,对雷击烧蚀损伤特征进行分析,并引入雷击烧蚀损伤指数DI,得出三种不同模型在不同铝涂层厚度、不同峰值雷电流作用下的烧蚀损伤规律,并对两种不同的局部喷铝防护系统下复合材料的损伤特征进行对比分析。结果表明:雷击防护系统下复合材料的烧蚀损伤面积和铝涂层厚度关系进行函数拟合,两者均满足幂函数关系。     

碳纤维复合材料结构损伤的自检方法研究进展

监测碳纤维增强树脂基复合材料(CFRP)的结构损伤是一个关键问题。本文就目前国内外研究较热且应用前景较大的一类新型无损检测技术——基于CFRP导电网络的自检技术进行综述,总结了直流法和交流法的原理和技术特点,尤其是对各种检测方法适用的环境和损伤类型进行了评估。最后指出了发展出一套智能化的CFRP结构损伤自检体系所要进一步开展的研究工作。     

除冰液对道面混凝土的影响及保护剂防护效果

通过冻融和化学侵蚀试验，研究了NW-056A机场道面除冰液对道面水混混凝土耐久性的影响以及在道面除冰液环境下两种新型混凝土保护剂的防护效果。结果表明：①混凝土在道面除冰液中冻融后表面无明显剥落现象，相对动弹模损失率比在水中小很多，道面除冰液延缓了混凝土的冻融破坏：②混凝土在道面除冰液常温浸泡下表面无剥蚀现象，但强度比在水中降低很多，因此存在化学腐蚀．且主要表现为对混凝土内部结构的缓慢损伤；（④两种新型混凝土保护剂均对预防混凝土的冻融破坏以及除冰液环境下的腐蚀破坏起到一定作用，涂刷混凝土保护剂是提高混凝土道面耐久性的有效方法。     

三种时频分析在复合材料无损检测中的应用

随着复合材料的广泛应用和现代信号处理技术的发展,时频分析方法已广泛应用于各类复合材料的损伤检测。将短时傅立叶变换、小波变换和黄氏变换三种时频分析技术经过Matlab编程,结合Lamb波应用于玻璃纤维增强的复合材料层合板的无损检测,并对三种时频结果进行比较与分析。结果表明：上述三种时频分析方法都能进行复合材料的损伤判定,但黄氏变换方法的分析精度更高。