基于功能危险性评估的民用飞机驾驶舱门设计探讨

FAA分别于2002年和2008年颁布25-106及25-127修正案,增加驾驶舱门安保事项以提高驾驶舱的安全水平。修正案要求加固驾驶舱门,驾驶舱门必须设计成可以阻止未被授权人员进入驾驶舱并且阻碍危险物体射入以保证机组人员的安全。驾驶舱门必须能检测驾驶舱失压并可以释放门或者卸压板平衡压力差,还应有措施使飞机机组成员在该舱门卡住的情况下能直接从驾驶舱进入客舱。因此,在驾驶舱门上设有一个可以快速释放的紧急出口。根据飞机驾驶舱门结构及功能的主要特点,对驾驶舱门功能故障进行探讨,同时对功能故障引发的危险性等级进行划分,以确定安全指标,进而辅助驾驶舱门设计工作。     

发动机动力模拟风洞试验中的空气桥技术

介绍了发动机动力模拟风洞试验中的空气桥设计技术和影响修正方法.通过自由度分析,选择了合理空气桥布局,采用有限元方法对空气桥关键受力梁进行了优化,建立了空气桥天平一体化数值模拟技术,使得空气桥和天平刚度更加匹配.通过这些设计及优化使得空气桥的作用力最小,并具有较强的克服压力影响、温度影响的能力.通过试验建立了空气桥附加刚度影响、内部压力影响、温度影响和内部流量影响的修正方法,进一步减小了空气桥对天平的影响.在8m×6m低速风洞进行了某大展弦比飞机全模涡扇动力模拟器(TPS)短舱动力模拟试验.试验结果重复性好,阻力系数精度达到0.0003,和相关文献吻合.这表明空气桥技术是成功的,满足了TPS短舱动力模拟试验要求.      

Numerical analysis and optimization of boundary layer suction on airfoils

Numerical approach of hybrid laminar flow control(HLFC) is investigated for the suction hole with a width between 0.5 mm and 7 mm. The accuracy of Menter and Langtry’s transition model applied for simulating the flow with boundary layer suction is validated. The experiment data are compared with the computational results. The solutions show that this transition model can predict the transition position with suction control accurately. A well designed laminar airfoil is selected in the present research. For suction control with a single hole, the physical mechanism of suction control, including the impact of suction coefficient and the width and position of the suction hole on control results, is analyzed. The single hole simulation results indicate that it is favorable for transition delay and drag reduction to increase the suction coefficient and set the hole position closer to the trailing edge properly. The modified radial basis function(RBF) neural network and the modified differential evolution algorithm are used to optimize the design for suction control with three holes. The design variables are suction coefficient, hole width, hole position and hole spacing. The optimization target is to obtain the minimum drag coefficient. After optimization,the transition delay can be up to 17% and the aerodynamic drag coefficient can decrease by 12.1%.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

飞翼无人机3种保形进气口进气道气动与隐身综合特性对比

基于飞翼布局无人机隐身与结构装载布置要求,保形设计了3种进气口形状的背负式S弯进气道,按照进口投影截面形状上、下底之比顺序排列,分别为三角形、梯形和矩形.利用数值模拟方法对无人机内外流场耦合流动进行计算分析,且基于射线弹跳(SBR)法对进气道电磁散射特性进行仿真研究,获得了飞翼无人机3种进气道的气动与隐身综合特性.研究结果表明:①矩形进气道模型升阻和纵向力矩特性表现均最好;②3种 进气道模型按顺序排列总压恢复系数逐渐增大,畸变指数逐渐减小,进气道沿程气流也逐渐顺畅,矩形进气道模型进气道内流特性最优;③0°迎角下3种进气道模型雷达散射截面(RCS)均值基本呈现先增大后减小的特征,进气道终端开放时矩形进气道模型隐身性能最好,而终端短路时三角形进气道模型隐身效果更优异.      

航空发动机高能碎片非包容事件故障树分析

为了使航空发动机高能碎片非包容事件满足适航安全性要求,运用故障树法对航空发动机该事件进行安全性分析并提出了分析方法的步骤和流程。引入最小割集和概率重要的度的概念,利用Isograph Reliability软件画出故障树并计算出高能碎片不包容事件的发生概率、最小割集以及概率重要度,通过对比最小割集和概率重要度,确定导致发动机高能碎片不包容主要的失效形式,并提出了有针对性的措施。     

S形进气道锤击波荷载特性分析

利用基于改进的延迟分离涡模拟（IDDES）方法,对亚声速和超声速来流条件下某S形模型进气道进行了非定常计算,研究了发动机喘振所产生的瞬时高压波形对锤击波传播规律的影响.结果表明:锤击波产生后沿进气道迅速向前传播,运动过程中锤击波的运动速度基本保持不变,但强度不断增强.同时受气流离心力的影响,S形进气道弯曲段半径较大一侧壁面受到的锤击波气动荷载值更大.发动机喘振所产生的瞬时高压的加载梯度增加使得锤击波传播速度及强度增强,而压力卸载方式对锤击波强度的影响不明显.在亚声速和超声速来流条件下,增加瞬时高压峰值均使得锤击波荷载强度显著增强,并近似符合二次函数分布规律,而且超声速来流条件下锤击波强度较亚声速来流更强.      

基于响应面法的短距/垂直起降飞机近地面升力损失

建立了短距/垂直起降(S/VTOL)飞机近地面升力损失的流场计算模型.通过数值模拟得出特定升力布局的飞机近地面状态各工况的升力损失.采用响应面法获得了飞机升力损失关于喷管落压比（NPR）、来流速度及飞机高度的2阶响应曲面函数及显著影响飞机升力损失的关键因素.并分析了喷管落压比、来流速度及飞机高度对飞机升力损失的交互影响作用,优化得出给定工况范围内升力损失最小的工作点.研究表明:仅考虑单因素影响时,升力损失随高度、落压比的增大而减小,随来流速度的增大而增大;考虑两因素交互作用时,高度与落压比及来流速度与落压比对升力损失存在交互影响,而高度与来流速度对升力损失无交互影响;优化获得的升力损失最小的工作点是飞机距地面高度为9D（D为喷管直径）、喷飞机高度为3、来流速度为0m/s,此时的升力损失为1.3%.      

球形点火腔对脉冲爆震DDT过程影响的数值研究

为了减小脉冲爆震发动机PDE（pulse detonation engine）单次循环时间,缩短爆燃向爆震转变DDT（deflagration to detonation transition）距离是关键.为此,提出了一种在头部添加球形点火腔的新型爆震管道结构设计方案,并采用丙烷和空气为可爆混合物,通过对新型爆震管DDT过程的二维数值模拟,研究其对DDT距离以及DDT时间的影响.数值模拟结果表明,头部采用球形点火腔后,点火腔中的压缩波经过多次反射后,能够在爆震管中更快地促使爆震波形成,DDT距离大大缩短;当球形点火腔直径为1.5倍等直爆震管直径时,相对于常规等直管爆震管结构,其DDT距离和过程时间分别减少了14%和16.26%.      

液体火箭发动机充液导管流固耦合动力学特性

为了深入研究流固耦合（FSI）作用对液体火箭发动机充液导管频率特性的影响,采用传递矩阵法(TMM)建立了空间导管流固耦合动力学计算模型.针对真实发动机导管开展了传递矩阵模型与传统基于附加质量的有限元(FEM)（非耦合）模型仿真计算以及模态试验验证,比较了管径、壁厚等结构参数对导管流固耦合作用的影响.结果表明:在流固耦合作用下,导管各阶谐振频率减小、而对应的流体振荡与结构振动幅值增大.管径对导管低阶频率特性的影响较壁厚对其影响更大.对于该算例,当管径大于设计值30%后,耦合作用引起的1阶频率误差高于10%,此时流固耦合不能忽略;而壁厚对1阶谐振频率的影响则小于8%.