Ca的掺入对复合氧化物LaFeO3和LaMnO3的结构及电性的影响

用柠檬酸法、固相法制备了替代的复合氧化物Ｌａ１－ｘＣａｘＦｅＯ３及Ｌａ１－ｘＣａｘＭｎＯ３。对样品进行了ＸＲＤ及导电能力测试。结果表明：Ｘ≤０．５，复合氧化物为单相的钙钛矿结构；Ｃａ的掺入，改善了ＬａＦｅＯ３导电性能，使其室温电阻率从６×１０＾４Ω·ｃｍ降低到１０Ω·ｃｍ左右；而对ＬａＭｎＯ３的影响不大，其室温电阻率在１０＾－１Ω·ｃｍ左右。     

基于CS8900A的工业级嵌入式网络接口实现

介绍了工业级以太网络控制芯片CS8900A—IQ3在嵌入式Internet中的应用，以实例详细对比说明了其在8位和16位两种运行模式下的硬件和软件实现。     

8802超低频标准相位产生器

８８０２超低频标准相位产生器采用数字技术，用Ｄ／Ａ变换方法产生正弦信号，由单片机控制频率和相位，频率由晶振综合产生，相位可数字预置，频率准确度高至±５×１０￣（－６），相位准确度高至±０．０００２°。介绍了主要技术指标、工作原理、技术特点和误差分析等。     

一种新型恒温—温补晶体振荡器

提出了一种ＯＣＸＯ的恒温控制方法。该方法是利用乙醇的沸点制成换态式恒温箱。这种温度控制方法既可以用作中准确度的ＯＣＸＯ，又可以作为精密双层控温ＯＣＸＯ的外层恒温装置，还可以与简单的温补线路结合，构成高准确度的ＯＴＣＸＯ。     

国内外航天器密封舱主结构材料的选用

介绍了国内外航天器密封舱主结构常用的铝合金材料,并对其常规力学性能、断裂韧度、焊接性能、抗应力腐蚀性能等进行了比较。同时,结合不同的使用环境及条件对可选材料进行了分析,给出了目前及未来密封舱主结构材料的选择建议。文章研究结果可为大型航天器密封舱主结构研制提供参考。     

Multiband echo tomography of Sco X-1

We present preliminary results of a simultaneous X-ray/optical campaign of the prototypical LMXB Sco X-1 at 1–10 Hz time resolution. Lightcurves of the high excitation Bowen/HeII emission lines and a red continuum at λ_c  6000 Å were obtained through narrow interference filters with ULTRACAM, and these were cross-correlated with simultaneous RXTE X-ray lightcurves. We find evidence for correlated variability, in particular when Sco X-1 enters the Flaring branch. The Bowen/HeII lightcurves lag the X-ray lightcurves with a light travel time which is consistent with reprocessing in the companion star while the continuum lightcurves have shorter delays consistent with reprocessing in the accretion disc.     

正态-复合非时齐Poisson过程模型结构可靠性当量正态设计

讨论强度R～N（μ_R，_R），应力｛S（t），t∈［0，T］｝为非时齐Poisson过程模型结构可靠性当量正态设计。获得应力在设计基准期［0，T］内的最大值概率分布及统计参数估计；正态－复合非时齐Poisson过程模型结构可靠度及结构可靠性当量正态设计表达式。     

P1─—多面体的对偶图形的性质

本文研究了P1─—多面体与其对偶图形的对偶图形边长之间的关系问题．设P1─—多面体的边长为a，其对偶图形的对偶图形的边长为C，则其中θ1为多面体A的过顶点的相邻两校之间的夹角，θ2为多面体B的过顶点的相邻两校之间的夹角，取θ＝max｛θ1，θ1｝     

Computational engineering analysis of external geometrical modifications on MQ-1 unmanned combat aerial vehicle

This paper focuses on the effects of external geometrical modifications on the aerodynamic characteristics of the MQ-1 predator Unmanned Combat Aerial Vehicle (UCAV) using computational fluid dynamics. The investigations are performed for 16 flight conditions at an altitude of 7.6 km and at a constant speed of 56.32 m/s. Two models are analysed, namely the baseline model and the model with external geometrical modifications installed on it. Both the models are investigated for various angles of attack from −4° to 16°, angles of bank from 0° to 6° and angles of yaw from 0° to 4°. Due to the unavailability of any experimental (wind tunnel or flight test) data for this UCAV in the literature, a thorough verification of calculations process is presented to demonstrate confidence level in the numerical simulations. The analysis quantifies the loss of lift and increase in drag for the modified version of the MQ-1 predator UCAV along with the identification of stall conditions. Local improvement (in drag) of up to 96% has been obtained by relocating external modifications, whereas global drag force reduction of roughly 0.5% is observed. The effects of external geometrical modifications on the control surfaces indicate the blanking phenomenon and reduction in forces on the control surfaces that can reduce the aerodynamic performance of the UCAV.     

螺旋桨桨叶1P气动载荷研究

介绍了一种１Ｐ载荷实验研究方法－桨叶应变测试法,首先通过桨叶剖面速度三角形及气动力分析给出了１Ｐ载荷与测量应变的关系,然后通过地面试验和飞行试验进行了验证。试验结果表明,螺旋桨１Ｐ载荷主要由于非对称气流流过桨盘面改变了桨叶剖面速度三角形而引起,迎角,侧滑角的增加,会产生较大的１Ｐ载荷;机动飞行,如快速拉杆,荷兰滚等也会产生较大的１Ｐ载荷。