高精度秒脉冲信号的产生

通过介绍高精度秒脉冲信号的实现原理以及实现中的关键技术,分析了如何减小由码跟踪环路测量误差导致的秒脉冲信号随机抖动误差,提出了减小由直接数字频率合成器导致的秒脉冲信号系统钟模糊误差的实现方法。最后给出了在＂北斗＂一号卫星标校机工程应用中的实际性能,统计精度（1倍标准差）为1.7ns,保证了标校设备能高精度地服务于BD-1导航定位系统。     

表达鸡传染性支气管病毒S1蛋白的重组假型杆状病毒的构建

根据鸡传染性支气管炎病毒M41株的基因序列(GenBank:AY851295.1),设计特异性引物,利用 RT-PCR方法扩增其 S1基因,并将扩增产物克隆到杆状病毒转移质粒pFast-VSV-G-CMV中,获得重组质粒pFast-VSV-G-CMV-S1,进一步将该重组质粒转化到DH10Bac感受态细胞中,得到重组穿梭载体Bacmid-CMV-S1,再利用脂质体转染sf9昆虫细胞,获得重组杆状病毒Ac-V-S1.间接免疫荧光试验表明,该重组杆状病毒可以转导哺乳动物细胞并表达S1蛋白.     

SiO2f/SiO2复合材料自身及其与铜、不锈钢的钎焊

采用AgCuTi活性钎料,在880℃/10min规范下成功实现了SiO2f/SiO2自身、SiO2f/SiO2与Cu和SiO2f/SiO2与1Cr18Ni9Ti三种接头的连接。实验结果表明,三种接头中靠近SiO2f/SiO2母材的界面处均形成了一层薄薄的扩散反应层组织,反应层中出现了Ti和O的富集,根据两者的原子比例推断生成了TiO2相;另外,三种接头中心区都形成了由灰色相和白色相共同组成的Ag-Cu共晶组织,其中灰色相为Cu基固溶体,白色相为Ag基固溶体。接头剪切强度结果显示,SiO2f/SiO2/Cu接头剪切强度为12.4MPa,SiO2f/SiO2/1Cr18Ni9Ti接头剪切强度为18.4MPa,接头中的残余应力是决定接头强度大小的重要因素之一。     

1-3型压电纤维主动叠层板扭转特性的研究

对4类典型铺层的1-3型压电纤维复合材料主动板的变形模式进行了理论分析。在此基础上对具有扭转变形模式的主动叠层板进行了振动特性分析,得到了该类型主动叠层板在外界电场激励下的稳态解。最后对该类主动叠层板的扭转振动特性进行了深入的研究,包括作用电场强度的大小、频率对扭转特性的影响、压电纤维铺层角和压电纤维体积比对主动叠层板扭转特性的影响等。算例表明本文计算模型和有限元得到的结果符合良好,同时算例结果表明含1-3型压电纤维复合材料主动叠层板具有良好的主动扭转特性。     

飞机航向神经网络PID参数自整定控制器研究

飞机航向操纵的模型参数具有非线性、慢时变特性。飞机航向操纵的传统控制方法的操纵性能不能令人满意。本文讨论一种应用BP神经网络实现PID参数自整定的控制方法。此法能根据飞机动态特性的变化，自动重新整定PID参数，从而改善了飞机航向的操纵性能和鲁棒性。     

基于S1,S2流面理论的液体火箭发动机涡轮内部流场计算

应用S1,S2流面理论对某大型液氢/液氧火箭发动机涡轮泵的两级轴流式涡轮内部跨声速流场进行计算和分析。流面的求解采用流线曲率法。将混合平面法的思想用于流线曲率法的求解过程中,对动、静叶排之间的相互干扰进行处理,将复杂的非定常问题简化为定常问题,从而简化计算。粘性的影响通过几种损失系数进行修正。计算结果较好地描述了涡轮内部的流动情况,为进一步完善涡轮设计、提高涡轮性能提供了理论依据。     

The Grain Impact Analyser and Dust Accumulator (GIADA) Experiment for the Rosetta Mission: Design, Performances and First Results

The Grain Impact Analyser and Dust Accumulator (GIADA) onboard the ROSETTA mission to comet 67P/Churyumov–Gerasimenko is devoted to study the cometary dust environment. Thanks to the rendezvous configuration of the mission, GIADA will be plunged in the dust environment of the coma and will be able to explore dust flux evolution and grain dynamic properties with position and time. This will represent a unique opportunity to perform measurements on key parameters that no ground-based observation or fly-by mission is able to obtain and that no tail or coma model elaborated so far has been able to properly simulate. The coma and nucleus properties shall be, then, clarified with consequent improvement of models describing inner and outer coma evolution, but also of models about nucleus emission during different phases of its evolution. GIADA shall be capable to measure mass/size of single particles larger than about 15 μm together with momentum in the range 6.5 × 10⁻¹⁰ ÷ 4.0 × 10⁻⁴ kg m s⁻¹ for velocities up to about 300 m s⁻¹. For micron/submicron particles the cumulative mass shall be detected with sensitivity 10⁻¹⁰ g. These performances are suitable to provide a statistically relevant set of data about dust physical and dynamic properties in the dust environment expected for the target comet 67P/Churyumov–Gerasimenko. Pre-flight measurements and post-launch checkouts demonstrate that GIADA is behaving as expected according to the design specifications. The International GIADA Consortium (I, E, UK, F, D, USA).     

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

新一代载人月面着陆器发展趋势研究

月面着陆器是实现载人探月任务的重要组成部分,从任务规划和着陆器参数两个方面对早期美国阿波罗计划中的月面着陆器（ LM）、苏联N1-L3登月计划中的月面着陆器（ L3登月系统）以及最近美国星座计划中的月面着陆器（ Altair）的相关情况进行了分析,并从任务需求、月面环境和研究经费及基础设施方面对LM与Altair月面着陆器进行详细比较,通过比较分析总结出新一代载人月面着陆器将沿着提高乘员运送能力、扩大到达范围、延长航天员生活时间及功能模块化的方向发展,并提出研制新一代月面着陆器应着重解决着陆器推进、结构、着陆障碍检测及缓冲以及月尘防护等关键技术。     

基于地月L1点的载人登月飞行方案分析

为解决传统载人登月方案中重型运载火箭难以研制、交会对接窗口选择困难等问题,提出了符合我国现有技术条件的基于地月L1点的载人登月方案设想。基于对圆形限制性三体模型和地月三,点特性的分析,将载人登月任务划分为不同的飞行阶段,研究了载人登月任务的规模、系统组成以及各舱段的质量分配等。通过与基于环月轨道方案各参数的分析和对比,提出通过付出较小代价将基于环月轨道的载人登月方案转化为基于地月,L1点的载人登月方案的方法。结果分析表明,经方案转化,不但能充分发挥地月L1点的优势,而且在一定条件下可以使节省燃料成为可能。