×××机翼主梁的寿命分布研究

本文通过运用Ｗ∧２统计量的检验方法对ＸＸＸ飞机八个失效的机翼主梁寿命分布进行了检验,得出该主梁寿命分布为威布尔分布。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.     

Sliding mode control design for oblique wing aircraft in wing skewing process

When the wing of Oblique Wing Aircraft (OWA) is skewed, the center of gravity, inertia and aerodynamic characteristics of the aircraft all significantly change, causing an undesirable flight dynamic response, affecting the flying qualities, and even endangering the flight safety. In this study, the dynamic response of an OWA in the wing skewing process is simulated, showing that the three-axis movements of the OWA are highly coupled and present nonlinear characteristics during the wing skewing. As the roll control efficiency of the aileron decreases due to the shortened control arm in an oblique configuration, the all-moving horizontal tail is used for additional roll and the control allocation is performed based on minimum control energy. Given the properties of pitch-roll-yaw coupling and control input and state coupling, and the difficulty of establishing an accurate aerodynamic model in the wing skewing process due to unsteady aerodynamic force, a multi-loop sliding mode controller is formulated by the time-scale separation method. The closed-loop simulation results show that the asymmetric aerodynamics can be balanced and that the velocity and altitude of the aircraft maintain stable, which means that a smooth transition is obtained during the OWA’s wing skewing.     

A tip clearance prediction model for multistage rotors and stators in aero-engines

Tip clearances of multistage rotors and stators greatly affect aero-engines’ aerodynamic efficiency, stability and safety. The inevitable machining and assembly errors, as well as the complicated error propagation mechanism, cause overproof or non-uniform tip clearances. However, it is generally accepted that tip clearances are difficult to predict, even under assembly state. In this paper, a tip clearance prediction model is proposed based on measured error data. Some 3D error propagation sub-models, regarding rotors, supports and casings, are built and combined. The complex error coupling relationship is uncovered using mathematical methods. Rotor and stator tip clearances are predicted and analyzed in different phase angles. The maximum, minimum and average tip clearances can be calculated. The proposed model is implemented by a computer program, and a case study illustrates its performance and verifies its feasibility. The results can be referred by engineers in assembly quality judgement and decision-making.     

Effects of wing flexibility on aerodynamic performance of an aircraft model

The low-speed wind tunnel experiment is carried out on a simplified aircraft model to explore the influence of wing flexibility on the aircraft aerodynamic performance. The investigation involves the measurements of force, membrane deformation and velocity field at Reynolds number of 5.4 × 10⁴–1.1 × 10⁵. In the lift curves, two peaks are observed. The first peak, corresponding to the stall, is sensitive to the wing flexibility much more than the second peak, which nearly keeps constant. For the optimal case, in comparison with the rigid wing model, the delayed stall of nearly 5° is achieved, and the relative lift increment is about 90%. It is revealed that the lift enhanced region corresponds to the larger deformation and stronger vibration, which leads to stronger flow mixing near the flexible wing surface. Thereby, the leading-edge separation is suppressed, and the aerodynamic performance is improved significantly. Furthermore, the effects of sweep angle and Reynolds number on the aerodynamic characteristics of flexible wing are also presented.     

涡轮叶尖间隙泄漏涡不稳定性分析

结合Rains间隙泄漏涡模型和长波不稳定性理论,应用高雷诺数k-ε湍流模型加壁面函数,基于压力修正的三维计算流体力学程序,对某一轴流涡轮平面叶栅叶尖间隙流场进行仿真,通过将叶尖间隙泄漏涡与其在机匣表面镜像形成的虚拟泄漏涡组合成一对泄漏涡,对涡轮叶尖间隙泄漏涡的不稳定性进行了分析,并计算了五个不同叶尖间隙高度下泄漏涡的最不稳定的波长及对应的频率。结果表明,利用长波不稳定性理论可以预测叶尖泄漏涡的不稳定性和最不稳定的波长及对应的频率,从而为采用合成射流控制方法去控制涡轮叶尖泄漏涡提供理论基础。     

Study on the lift and propulsive force shares to improve the flight performance of a compound helicopter

To investigate the effects of lift and propulsive force shares on flight performance, a compound helicopter model is derived. The model consists of a helicopter model, a wing model and a propeller model. At a low speed of 100 km/h, the Lift-to-Drag ratio(L/D) of the compound helicopter is improved when the wing provides 20.2% of the take-off weight. At high speeds, the L/D can be improved when the propeller provides the total propulsive force. Lowering the main rotor speed increases the wing lif...     

Lock-in phenomenon of tip clearance flow and its influence on aerodynamic damping under specified vibration on an axial transonic compressor rotor

In this study, the lock-in phenomenon of Tip Clearance Flow(TCF) instabilities and their relationship to blade vibration are investigated numerically on an axial transonic rotor with a large tip clearance. The capabilities of simulating instability flow and lock-in phenomenon are verified on a transonic rotor and a NACA0012 airfoil by comparing with the test data, respectively.The lock-in phenomenon is first numerically confirmed that may occur to TCF instabilities when its frequency is close to...     

Mass and performance optimization of an airplane wing leading edge structure against bird strike using Taguchi-based grey relational analysis

Collisions between birds and aircraft are one of the most dangerous threats to flight safety. In this study, smoothed particles hydrodynamics (SPH) method is used for simulating the bird strike to an airplane wing leading edge structure. In order to verify the model, first, experiment of bird strike to a flat aluminum plate is simulated, and then bird impact on an airplane wing lead-ing edge structure is investigated. After that, considering dimensions of wing internal structural components like ribs, skin and spar as design variables, we try to minimize structural mass and wing skin deformation simultaneously. To do this, bird strike simulations to 18 different wing structures are made based on Taguchi’s L18 factorial design of experiment. Then grey relational analysis is used to minimize structural mass and wing skin deformation due to the bird strike. The analysis of variance (ANOVA) is also applied and it is concluded that the most significant parameter for the performance of wing structure against impact is the skin thickness. Finally, a validation simu-lation is conducted under the optimal condition to show the improvement of performance of the wing structure.     

可重复使用运载器机翼外形优化

研究了有翼可重复使用运载器机翼平面外形参数优化设计问题。在高超声速配平和低速水平着陆性能等约束条件下，利用混合遗传算法和粒子群优化算法来选择最优机翼外形参数，使机翼重量最小化。在已知的不同质心位置下求得相应的最小重量机翼外形。亚声速气动力采用面源法计算，高超声速气动力采用修正的牛顿流理论计算。为了降低计算耗费，使用均匀设计和逐步回归方法建立了低速气动力回归模型。整个优化过程在Matlab集成环境下完成。