Computational aerodynamic analysis on perimeter reinforced （PR）-compliant wing

Abstract Implementing the morphing technique on a micro air vehicle （MAV） wing is a very chal- lenging task, due to the MAWs wing size limitation and the complex morphing mechanism. As a result, understanding aerodynamic characteristics and flow configurations, subject to wing structure deformation of a morphing wing MAV has remained obstructed. Thus, this paper presents the investigation of structural deformation, aerodynamics performance and flow formation on a pro- posed twist morphing MAV wing design named perimeter reinforced （PR）-compliant wing. The numerical simulation of two-way fluid structure interaction （FSI） investigation consist of a quasi- static aeroelastic structural analysis coupled with 3D incompressible Reynolds-averaged Navier- Stokes and shear-stress-transport （RANS-SST） solver utilized throughout this study. Verification of numerical method on a rigid rectangular wing achieves a good correlation with available exper- imental results. A comparative aeroelastic study between PR-compliant to PR and rigid wing per- formance is organized to elucidate the morphing wing performances. Structural deformation results show that PR-compliant wing is able to alter the wing＇s geometric twist characteristic, which has directly influenced both the overall aerodynamic performance and flow structure behavior. Despite the superior lift performance result, PR-compliant wing also suffers from massive drag penalty, which has consequently affected the wing efficiency in general. Based on vortices investigation, the results reveal the connection between these aerodynamic performances with vortices formation on PR-comoliant wing.     

Form-finding methods for deployable mesh reflector antennas

Deployable high-frequency mesh reflector antennas for future communications and obser- vations are required to obtain high gain and high directivity. In order to support these new missions, reflectors with high surface accuracy are widely required. The form-finding analysis of deployable mesh reflector antennas becomes more vital which aims to determine the initial surface profile formed by the equilibrium prestress distribution in cables to satisfy the surface accuracy requirement. In this paper, two form-finding methods for mesh reflector antennas, both of which include two steps, are pro- posed. The first step is to investigate the prestress design only for the cable net structure as the circum- ferential nodes connected to the supporting truss are assumed fixed. The second step is to optimize the prestress distribution of the boundary cables connected directly to the supporting truss considering the elastic deformation of the antenna structure. Some numerical examples are carried out and the simulation results demonstrate the proposed form-finding methods can warrant the deformed antenna reflector surface matches the one by design and the cable tension forces fall in a specified range.     

自锁型重物提升机构在生产中的应用

针对生产中重物产品,半成品物流,包装过程中提升困难的问题,提出了自锁型重物提升机构,以达到节能,降低运行成本,降低劳动强度的目的.     

LEO/MEO双层空间信息网中基于身份的群组密钥管理方案

由于空间信息网中结点的移动性,在空间信息网中实现传统的群组密钥管理面临许多困难.根据空间信息网的特点,分析了空间信息网中群组密钥管理方案的需求,设计了一个适用于LEO/MEO双层空间信息网络的群组密钥管理方案,采用基于身份的思想,消除了对证书系统的依赖,能在空间信息网中灵活高效地实现.将空间信息网中的结点根据其逻辑位置划分为簇,其中簇头为MEO卫星,在密钥交换阶段中共享密钥仅由所有簇头结点决定,这种机制大大减少了通信量.方案能有效抵抗外部攻击者,并且具有前向保密性和后向保密性.仿真实验表明,方案具有很高的通信效率.     

一种新的柔性蜂窝结构及其在变体飞机中的应用

变体色机要求机翼结构可以光滑连续地变形.机翼的蒙皮要有足够大的面内伸缩变形能力,同时还要有足够的面外承载能力.本文针对后缘变弯度机翼,设计出一种新的柔性蜂窝结构.研究了该柔性蜂窝的面内变形能力和形状参数的关系.仿真分析和试验验证表明,该柔性蜂窝结构具有足够的面内变形能力,变形后仍保持良好的面外承载能力,满足后缘变弯度机...     

均匀化处理对7A55铝合金组织与性能的影响

研究了单级均匀化和双级均匀化工艺对铸态7A55铝合金组织和性能的影响规律.结果表明,经450℃单级均匀化处理后,合金中的残留共晶仍然较多,保温60h时合金中残留共晶比例由铸态合金的15.2%减少至7.2%,合金硬度由72HRB降低至60HRB,伸长率则由2.1%增大至11.2%;经450℃/60h+470℃双级均匀化处...     

基于流固耦合的实体元空心叶片鸟撞数值模拟

针对通用流固耦合算法在模拟实体元结构破坏上的不足,以MSC.DYTRAN软件为平台,研究了不考虑和考虑失效的实体元平板叶片流固耦合数值模拟方法。在此基础上,建立了实体元空心叶片鸟撞瞬态动力学有限元模型,计算分析了叶片在稳定旋转状态下遭受不同密度、长度、半径及速度鸟体撞击下的叶片应力的瞬态响应,计算表明：上述参数值增加均会增大叶片的应力峰值,并且对应力峰值的影响都不是线性的。最后模拟了叶片的失效过程。     

环境严酷性指数腐蚀当量方法及其应用研究

 建立统一的腐蚀损伤环境变量——环境严酷性指数（ESI）,并研究其在飞机结构耐久性设计中的应用。在材料/结构腐蚀与单一环境类型/要素/强度关系基础上,按照《由电化学测量值计算腐蚀率和相关量的标准方法》(ASTM G102 89),引入并给出相应的ESI,并在一定工程假设下,给出在综合环境(由不同环境类型/要素/强度组成)作用下的ESI。同时,在腐蚀损伤等效原则下,用标准的环境类型/要素/强度及其作用时间当量化地表征综合环境及相应的作用时间(即环境谱),为环境加速试验环境当量提供依据并形成环境当量谱以应用于飞机结构耐久性设计中的腐蚀防护与控制(EEF),评估结构的检查周期/日历寿命。根据相关试验结果计算了典型金属材料在不同环境中的环境严酷性指数及环境当量化系数(EEF), 给出了环境简化或折算的算例。     

Variable Structure Control of Catastrophic Course in Airdropping Heavy Cargo

The mathematical model of a transport aircraft would be subjected to a sudden change when heavy cargo is dropped off in airdropping, which exerts serious influences upon the safety of the aircraft. A variable structure controller is specially designed for handling the airdrop process. The nonlinear system is linearized by input-output feedback linearization using differential geometry theories. On this basis, an inner loop system for velocity and attitude tracking control is designed by using the exponentially approaching rule of the variable structure theory. The whole flight control system is integrated with the outer loop flight altitude control. Digital simulation evidences the applicability of the system to potentially catastrophic course in airdropping heavy cargo and provides robustness against system parameter perturbation.     

一种大变形多空间域连续体结构拓扑优化方法

针对大变形非线性结构拓扑优化问题,提出了基于混合细胞自动机(HCA, Hybrid Cellular Automata)多空间域连续体结构拓扑优化方法;采用密度法,建立了单元相对密度表示的材料弹-塑性模型;以单元相对密度和应变能作为细胞自动机(CA,Cellular Automata)的状态信息,利用CA局部控制规则,修改相对密度,迭代实现各设计空间域应变能均匀分布;设计了多空间域拓扑优化HCA算法,采取多个对象同时耦合优化迭代,各自收敛策略,解决了多空间域优化迭代算法收敛稳定性问题;最后,以汽车保险杆结构横梁和支撑等两个设计空间为例,施加大变形动态载荷作用,对提出的多空间结构优化算法进行了验证,优化后结构有效地降低了碰撞作用力峰值达54％,提高了结构安全性.