无人车基于激光雷达/视觉的目标体积自动测量方法

近些年,基于激光雷达和视觉的目标感知在无人系统中得到了广泛应用。目标的体积测量在很多应用场景可以发挥极其重要的作用,然而对识别感知目标的体积测量,目前尚无大量研究。首次提出了一种基于激光雷达/视觉的无人车目标体积自动测量方法,实现了无人车与目标体积测量功能的结合。通过在LeGO-LOAM算法中加入点云畸变补偿,相较于原始LeGO-LOAM算法,无人车在高速情况下的构图精度得到提升;通过将激光雷达与视觉进行深度融合,实现了目标的自动识别与全局定位;通过基于平面拟合的地面分割与欧式聚类,实现了目标点云轮廓的实时获取;通过设计一种基于切片法的不规则物体体积测量方法,实现了无人车在运动情况下对目标体积的自动估计。最终,分别通过Gazebo仿真和实际试验验证了算法的有效性。试验结果表明,所提算法在无人车运动的情况下对静态目标物的实时体积测量精度优于3%,具有较好的工程应用价值。     

三维编织复合材料细观结构参数对有效弹性模量影响

应用细观力学方法对三维编织结构复合材料的有效性能进行预测是研究编织复合材料宏观性能的重要途径。细观结构参数决定编织体内纤维束的结构形态特征及复合材料的各种性能。根据作者提出的三维四向编织复合材料代表单元模型 ,文章应用选择平均法 (SAM)详细的分析了主要细观结构参数(单步步长、纤维束弯曲半径 )与编织体有效弹性模量之间的变化关系 ,分析了细观结构参数对编织体有效弹性模量的影响 ,为材料优化设计奠定基础     

不同重力环境下间隙铰链关节磨损分析

为研究不同重力环境对空间机构间隙铰链关节磨损的影响,将机械系统摩擦学行为和动力学行为相耦合,建立了磨损与动力学耦合分析模型和数值计算框架。首先采用非线性弹簧阻尼模型作为间隙处接触碰撞力的计算模型,同时采用Coulomb 法来计算运动副间隙处的摩擦力,进而建立了含间隙的机构动力学模型;然后通过基于Archard磨损模型二次开发的ANSYS程序来计算磨损,其中运用节点位移的方法来描述磨损过程。结果表明：当间隙关节转速较低时,重力对于关节轴承的磨损分布和磨损程度的影响很大,轴承出现集中磨损现象,磨损间隙急剧增加,严重影响机构的性能和精度;随着关节转速升高,重力对间隙关节磨损的影响逐渐减弱,轴承的磨损分布、磨损程度和关节最大磨损间隙的增长率将逐渐与微重力环境下趋同。     

基于控制体积方法的降落伞初始充气模型

考虑降落伞初始充气过程中降落伞变形情况与受力特性,建立了基于控制体积方法的初始充气模型。模型从理想气体状态方程出发,通过伞衣内部气体质量求解伞衣内部各个部分所受压力,将压力结果代入基于凯恩方法建立的伞衣结构模型中,即可得到对应的伞形;模型在计算时能够考虑伞衣结构透气的影响。数值计算的结果表明,模型计算得到的初始充气过程伞衣形状变化与试验吻合较好,初始充气时间与经验公式基本一致。该方法还可用于对降落伞主充气阶段的数值模拟。     

一种燃油箱绿色惰化系统地面惰化性能分析

在描述一种采用催化燃烧产生惰气来降低油箱气相空间氧体积分数的新型绿色惰化工作原理基础上,设计了绿色惰化系统流程,通过一定的假设和简化建立了其数学模型并进行了求解.将结果与采用中空纤维膜产生富氮气体的机载惰化系统进行了比较,结果显示:当绿色惰化系统中抽吸气的流量与中空纤维膜惰化所产生富氮气体流量一致时,前者惰化效果远好于后者.同时,还研究了催化反应器效率和预热气体抽取比例对绿色惰化系统的影响,结果表明:提高反应器效率可有效缩短达到安全氧体积分数所需的时间,且最终油箱气相空间氧体积分数会降低,而选取合适的预热气体抽取比例可以减少系统能耗.      

A fast and automatic full-potential finite volume solver on Cartesian grids for unconventional configurations

To meet the requirements of fast and automatic computation of subsonic and transonic aerodynamics in aircraft conceptual design,a novel finite volume solver for full potential flows on adaptive Cartesian grids is developed in this paper.Cartesian grids with geometric adaptation are firstly generated automatically with boundary cells processed by cell-cutting and cell-merging algo rithms.The nonlinear full potential equation is discretized by a finite volume scheme on these Cartesian grids and iteratively solved in an implicit fashion with a generalized minimum residual (GMRES) algorithm.During computation,solution-based mesh adaptation is also applied so as to capture flow features more accurately.An improved ghost-cell method is proposed to implement the non-penetration wall boundary condition where the velocity-potential of a ghost cell is modified by an analytic method instead.According to the characteristics of the Cartesian grids,the Kutta condition is applied by specially computing the gradients on Kutta-faces without directly assigning the potential jump to cells adjacent wake faces,which can significantly improve the solution con verging speed.The feasibility and accuracy of the proposed method are validated by several typical cases of sub/transonic flows around an ONERA M6 wing,a DLR-F4 wing-body,and an unconventional figuration of a blended wing body (BWB).The validation cases demonstrate a fast convergence with fully automatic grid treatment and computation,and the results suggest its capacity in application for aircraft conceptual design.     

CVD技术制备Ta/W层状复合材料

运用化学气相沉积(Chemical Vapor Deposition,CVD)技术制备了W体积分数分别10%,13%和18%的Ta/W两层层状复合材料,采用金相显微镜(OM)、扫描电镜(SEM)和室温拉伸实验对复合材料的性能进行分析。结果表明:运用CVD技术可以制备W体积分数不同,且密度优于理论密度99.4%的层状复合材料;复合材料中Ta,W层的晶粒均为柱状晶粒,离界面越近,晶粒越细;沉积态复合材料的力学性能优于纯CVD Ta和CVD W;1600℃×2 h的热处理后,复合材料的界面扩散层宽度显著增大,力学性能高于沉积态的力学性能,最高抗拉强度可达660 MPa。     

Numerical Simulation of Rotor Flow Field Based on Overset Grids and Several Spatial and Temporal Discretization Schemes

A numerical method based on solutions of Euler/Navier-Stokes (N-S) equations is developed for calculating the flow field over a rotor in hover. Jameson central scheme, van Leer flux-vector splitting scheme, advection upwind splitting method (AUSM) scheme, upwind AUSM/van Leer scheme, AUSM+ scheme and AUSMDV scheme are implemented for spatial discretization, and van Albada limiter is also applied. For temporal discretization, both explicit Runge-Kutta method and implicit lower-upper symmetric Gauss-Seidel (LU-SGS) method are attempted. Simultaneously, overset grid technique is adopted. In detail, hole-map method is utilized to identify intergrid boundary points (IGBPs). Furthermore, aimed at identification issue of donor elements, inverse-map method is implemented. Eventually, blade surface pressure distributions derived from numerical simulation are validated compared with experimental data, showing that all the schemes mentioned above have the capability to predict the rotor flow field accurately. At the same time, vorticity contours are illustrated for analysis, and other characteristics are also analyzed.     

区域运输规划模型系统

提出一种区域运输规划模型系统,以求从定量的角度,预测一个区域内的货物运输量,继而确定这些运输量对该区域内存在的多种运输方式的偏好结构,最后仿真这些运量在相应的各种运输网络上的分布情况,同时仿真模型还对运输网线路经过新建或扩建后所形成的新的运量分布进行模拟。根据运量分布情况,就可提出初步的规划建设方案。     

翼型舵面偏转非定常流动数值模拟

针对NACA0012翼型舵面偏转问题,数值模拟了不同参数对翼型气动特性的影响。基于非结构动网格技术,采用ALE有限体积描述下的二维可压缩非定常N-S方程,计算通量采用Vanleer格式、时空二阶格式,利用Venkatakrishnan限制器抑制数值振荡。非定常计算结果表明,NACA0012翼型绕1/4弦点作周期性俯仰振动的升力系数和俯仰力矩系数结果与实验数据吻合良好,验证了数值方法的准确性;在翼型舵面表面有分离区产生,升力系数和俯仰力矩系数形成滞回环,在亚声速情况下,滞回环幅值较小,进入超声速阶段以后,幅值增大,随着翼型间缝隙宽度逐渐增加,翼型升力系数和俯仰力矩系数与无缝翼型相比逐渐降低。