K8飞机液压泵断轴的原因分析及对策

对Ｋ８飞机液压泵断轴这一故障,从飞机系统及液压泵本身进行了分析、计算和试验,证实了这一故障是由于该型液压泵与ＹＨ－１０不相容造成的,并由此提出了解决办法。     

涡轮转子凹槽叶尖泄漏流动气动热力特征

为探索总结凹槽叶尖泄漏流动气动热力特征,利用实验和数值模拟方法,对叶尖凹槽内部旋涡相互作用机理和叶顶流动换热与泄漏流能量再分布等问题进行研究,并对凹槽叶尖参数化设计方法进行探讨。结果表明:搭建的考虑多因素实验台和可视化泄漏流动测量方案可以精确地捕捉到叶顶区域的流动结构;刮削涡在凹槽中起到"气动篦齿"作用,其形态特征的变化直接影响凹槽叶尖对泄漏流动的控制效果;高温泄漏流流体对叶片表面的冲击是叶尖热负荷提高的主要原因;合理选择叶尖气动参数和凹槽的几何参数可以有效控制刮削涡形态,最终提升叶尖气动热力性能。     

一种平面埋入式进气道的地面工作特性及流态特征

对一种平面埋入式进气道的地面工作特性进行了实验研究, 结合数值仿真技术, 分析了地面工作状态下该类进气道的流态特征, 并探讨了其出口总压图谱的形成成因.结果表明:(1)虽然进气道出口截面的二次流较弱, 但通道内却存在强的以对涡为特征的旋流, 该对涡因埋入式进气道进口侧棱的存在而产生, 与后唇口前缘的气流分离共同导致了进气道出口截面的大面积低总压区;(2)地面工作状态下, 埋入式进气道的总压恢复系数随出口马赫数的上升而下降, 周向畸变指数、紊流度和综合畸变指数则随着出口马赫数的增加而增加.在相同的出口马赫数下, 地面工作状态的总压恢复系数高于飞行状态, 各种畸变指数也明显偏高.但当发动机的进口工作马赫数为0.35左右时, 进气道出口截面的综合畸变指数W小于10.0%, 满足常规发动机的稳定工作要求;(3)计算和实验结果对比表明, 所得到的进气道出口总压恢复系数相对误差在1.2%以内, 但畸变指数整体偏大.      

Impact of the thermal effect on the load-carrying capacity of a slipper pair for an aviation axial-piston pump

A thermal hydraulic model based on the lumped parameter method is presented to analyze the load-carrying capacity of a slipper pair in an aviation axial-piston pump under specified operating conditions. Both theoretical and experimental results are presented to demonstrate the validity of the thermal hydraulic model. The results illustrate that the squeezing force and thermal wedge bearing force are the main factors that affect the film thickness and load-carrying capacity. At high oil temperature and high load pressure, the film thickness decreases with increasing clamping force due to a combined action of the squeezing bearing force and the thermal wedge bearing force, but the load-carrying capacity will increase. An increase of the film thickness is proven to be beneficial under high shaft rotational speed but especially dangerous as it strongly increases the ripple amplitude of the film thickness, which leads to decreasing the load-carrying capacity. The structural parameters of the slipper can be optimized to achieve desired performance, such as the slipper radius ratio and orifice length diameter ratio. To satisfy the requirement of the load-carrying capacity, the slipper radius ratio should be selected from 1.4 to 1.8, and the orifice length diameter ratio should be selected from 4 to 5.     

Effect of boundary conditions on downstream vorticity from counter-rotating swirlers

Particle image velocimetry(PIV) is utilized to measure the non-reacting flow field in a reflow combustor with multiple and single swirlers. The velocity field, vortex structure and total vorticity levels are experimentally obtained using two different boundary conditions, representing a single confined swirler and multiple swirlers in an annular combustor. The influence of the boundary conditions on the flow field at several locations downstream of the swirlers is experimentally investigated, showing that the central vortex in the multi-swirler case is more concentrated than in the single-swirler case. The vorticity of the central vortex and average cross-sectional vorticity are relatively low at the swirler outlet in both cases. Both of these statistics gradually increase to the maximum values near 20 mm downstream of the swirler outlet, and subsequently decrease. It is also found that the central vortex in the multi-swirler case is consistently greater than the single-swirler case. These results demonstrate the critical influence of boundary conditions on flow characteristic of swirling flow, providing insight into the difference of the experiments on testbed combustor and the full-scale annular combustors.     

叶片前缘旋流和常规冲击对比数值研究

为了寻求更好的叶片前缘内冷结构,对旋流冲击和常规冲击的流动和传热特性进行了数值模拟,对比研究了二者的涡流结构、传热强度、流动阻力、综合传热性能和热均匀性,研究了通道Re数和冲击间距对这些参数的影响。结果表明旋流冲击形成的旋涡有利于传热的增强和热均匀性的提高。在所研究的Re数（2×104~7.78×104）和冲击间距（3.3~5倍直径）范围内,旋流冲击与常规冲击相比平均传热增强18%~34%,增幅随Re数和冲击间距的增大而增大;流阻增大10%~26%,增幅随Re数和冲击间距的增大而减小;综合传热性能增强20%左右;热均匀性提高60%左右。     

Evaluation of pressure oscillations by a laboratory motor

Aeroacoustic pressure oscillation is one of the important challenges in segmented solid rocket motors with high slenderness ratio. The reason for these oscillations can be searched in vortex shedding due to grain burning surfaces, holes and slots. In this paper, a novel sub-scaled motor was used for evaluation of aeroacoustic pressure oscillations. First, the related parameters to scale down using Buckingham’s Pi-theorem were determined and then the sub-scaled motor was designed and manufactured. After this, Strouhal number in various grain forms and vortex shedding prediction criteria have been discussed. Then, one-dimensional linear and non-linear solution approaches have been presented. To understand the motor internal flow and vortex shedding formation, steady state computational fluid dynamic performed for seven regression steps and finally, two static tests have been performed. Results show that various definitions for Strouhal number are useful only for primarily glance on vortex shedding and pressure oscillations and so CFD solution and the test program are inevitable for a correct understanding of the ballistic operational condition of the motor. Experimental results demonstrated the existence of such oscillations with frequencies nearly equal to axial modes. It seems that non-linear parameters have small effects on aeroacoustic pressure oscillation and therefore the linear solution is acceptable to obtain approximate data. Of course, it should be emphasized that linear solution represents oscillations on overall motor action time, whereas the output of non-linear solution depends on thermochemistry properties of solid propellant and combustion products. Therefore, with a non-linear solution, oscillations maybe occur in some intervals of action time. FFT (Fast Fourier Transformation) results demonstrated that although both first and second acoustic modes have been excited, the position of longitudinal oscillation has an important role on which one is dominant.     

基于IDDES方法和γ-Re_θ转捩模型的粗糙颗粒诱导高速边界层强制转捩模拟

采用γ-Re_θ转捩模型与IDDES (Improved Delayed Detached Eddy Simulation)相结合的方法对BAM6QT (Boeing/AFOSR Mach-6 Quiet Tunnel)中的马赫6来流条件下粗糙颗粒诱导转捩情况进行了数值模拟研究,通过与试验测量的压力脉动均方根值、脉动主频和边界层内的皮托压分布的定量对比及与文献中DNS (Direct Numerical Simulation)流场结构的定性对比,表明该方法可以捕捉粗糙单元诱导出的流向涡,能够模拟颗粒前缘分离激波和弓形激波之间的震荡现象,能够模拟流向涡向下游的发展失稳过程及其脉动发展过程。计算结果表明流向涡结构在粗糙颗粒下游40倍颗粒直径位置开始破碎,非定常扰动能也在该点附近增长达到最大值。粗糙单元诱导出了明显的条带涡结构,其中低速条带处于边界层上层,在向下游发展的过程中逐渐扩散至边界层外缘并耗散掉。高速条带位于边界层底部,在向下游发展的同时往展向两侧拓展,最终展向上多条高速条带接触并互相耦合,导致最后条带涡结构的破碎和尾迹区边界层的转捩。     

电磁阀滑动副的设计参数灵敏度分析与可靠性研究

分析了电磁阀的组成和功能,给出了电磁阀的4个典型任务剖面,并由此分析对阀门可靠性产生重要影响的功能结构。用设计参数灵敏度分析法研究了导致阀芯-壳体滑动副卡死的直接原因,认为问题的核心在于多余物导致摩擦力大幅度增加。因此消除滑动副的疲劳磨损和粘着磨损是提高可靠性的关键。用质量功能配置方法找出了与滑动副相关的零件和结构,在灵敏度分析的基础上建立了结构要素的设计思路和原则,研究了螺管式电磁阀的滑动副结构对空间推进系统的适用性,并给出了滑动副结构要素的加工方法和对应的工序质量控制点。     

无人机近距编队飞行建模与仿真

无人机编队飞行有着单架无人机无法比拟的优点,但属于较新的研究领域。从无人机未来发展需求出发,根据近距编队的特点,提出了一种近距编队控制方法,并以双机近距编队为基础对控制律设计和算法实现进行了研究。通过建立僚机旋转参考系下的双机编队相对运动模型,同时考虑长机翼尖涡对僚机产生的气动耦合效应,基于PI控制设计了一种无人机近距编队飞行控制器,通过仿真验证和比较分析,证明僚机可以很好地跟随长机的机动保持编队构型,验证了提出的编队飞行控制方法的可行性和有效性。