Numerical investigation on flow field characteristics of dual synthetic cold/hot jets using POD and DMD methods

In order to improve the control ability of synthetic jets in compressible boundary layer, a novel control method based on dual synthetic cold/hot jets coupled control of velocity profile and temperature profile was proposed. As fundamental investigations on the effects of synthetic jet temperature on the jet behavior and flow field characteristics were essentially necessary, preliminary numerical simulations were conducted to study the influence of temperature (200 K and 400 K) on the flow field characteristics of synthetic jets using Large Eddy Simulations (LES) model. Time-averaged flow fields showed that different temperatures led to variable behavior of two strands of jets. For dual synthetic cold jets, a potential-core arose apparently with its height ranging from 0.01 to 0.03 m, while for dual synthetic hot jets, two strands of jets emerged downstream. The modal decomposition of instantaneous flow fields had been done using both Proper Orthogonal Decomposition (POD) and Dynamic Mode Decomposition (DMD). Various modes showed different characteristics of the flow fields. As the POD method focuses on the energy of flow while the DMD method focuses on the frequency, the first two modes had many similarities, but the third and fourth modes demonstrated completely different vortex structures. The current researches play a role of preliminary investigations for further and comprehensive exploration of novel flow control measures in global velocity field.     

Supersonic flow over a pitching delta wing using surface pressure measurements and numerical simulations

Experimental and numerical methods were applied to investigating high subsonic and supersonic flows over a 60° swept delta wing in fixed state and pitching oscillation.Static pressure coefficient distributions over the wing leeward surface and the hysteresis loops of pressure coefficient versus angle of attack at the sensor locations were obtained by wind tunnel tests.Similar results were obtained by numerical simulations which agreed well with the experiments.Flow structure around the wing was also demonstrated by the numerical simulation.Effects of Mach number and angle of attack on pressure distribution curves in static tests were investigated.Effects of various oscillation parameters including Mach number, mean angle of attack, pitching amplitude and frequency on hysteresis loops were investigated in dynamic tests and the associated physical mechanisms were discussed.Vortex breakdown phenomenon over the wing was identified at high angles of attack using the pressure coefficient curves and hysteresis loops, and its effects on the flow features were discussed.     

旋涡破裂对单独翼气动特性的影响及其工程估算方法

本文介绍了旋涡破裂对单独翼纵向和横向气动特性的影响,在分析和归纳实验数据的基础上,提出估算旋涡破裂对单独翼纵向和横向气动特性影响的工程方法。     

NUMERICAL SIMULATION OF VORTEX BREAKDOWN ON A DELTA WING AT LOW SPEED

ＮＵＭＥＲＩＣＡＬ　ＳＩＭＵＬＡＴＩＯＮ　ＯＦ　ＶＯＲＴＥＸ　ＢＲＥＡＫＤＯＷＮ　ＯＮ　Ａ　ＤＥＬＴＡ　ＷＩＮＧ　ＡＴ　ＬＯＷ　ＳＰＥＥＤＺｈｕＺｉｑｉａｎｇ；ＪｉａＪｉａｎｂｏ（ＩｎｓｔｉｔｕｔｅｏｆＦｌｕｉｄＭｅｃｈａｎｉｃｓ，ＢｅｉｊｉｎｇＵｎ...     

三角翼涡破裂非定常特性实验研究

本文依据染色液流动显示结果,通过子波和频谱分析,探讨了70°三角翼前缘涡涡核轴向速度的变化规律及其子波特性、涡破裂位置的非定常特性,指出涡破裂点位置的变化属于低频高幅振荡,这主要是左右涡之间的相互作用造成的,当两个涡的时间平均涡破裂点位置彼此靠得更近时,相应的振荡就更大一些,此外本实验得到涡破裂位置振荡的折合频率在St=0.2以内.     

非定常扰动对涡破裂的影响

在旋涡发生器内进行了涡管内的涡破裂研究。试验表明,不论是泡状或是螺旋状破裂,趋近破裂点时流速均趋于零;非定常扰动使涡轴附近的轴向速度增大,从而延缓了涡破裂的发生;在定常流参数、扰动频率和振幅的适当组合下,扰动可促使破裂状态由泡状转变为螺旋状,大大推迟涡破裂的发生。初步的理论分析表明,上述现象可能来源于流动共振。文中最后还给出了水槽中前缘振动襟翼的实验结果。试验表明,襟翼振动可延缓破裂的发生,且存在一个最佳的频率。试验中还发现,大迎角时,若襟翼不振动,可交替地只在一侧产生前缘涡,襟翼振动可消除这一现象。     

非定常集中涡破裂形态及其对扰动的影响

本文中利用三角翼前缘涡襟翼的强制振动来推迟涡破裂。流场显示实验结果表明,在有强制扰动时,集中涡显示出两种不同形式的破裂,可分成六种不同的破裂形态。非定常集中涡的一个破裂过程涉及几种破裂形态之间的转换。涡襟翼振动产生的非定常效应对涡破裂的影响与三角翼后掠角有密切的关系,随后掠角增大非定常效应的影响变小。就实验迎角范围而言(α<35°),对50°后掠角三角翼,涡襟翼振动可显著推迟涡破裂;但对70°后掠角三角翼,振动却能促进涡的破裂。涡襟翼振动改变了集中涡的性态,使集中涡趋向于和前缘平行。振动对涡破裂的作用部分地与这种效应有关。     

Effect of boundary conditions on downstream vorticity from counter-rotating swirlers

Particle image velocimetry(PIV) is utilized to measure the non-reacting flow field in a reflow combustor with multiple and single swirlers. The velocity field, vortex structure and total vorticity levels are experimentally obtained using two different boundary conditions, representing a single confined swirler and multiple swirlers in an annular combustor. The influence of the boundary conditions on the flow field at several locations downstream of the swirlers is experimentally investigated, showing that the central vortex in the multi-swirler case is more concentrated than in the single-swirler case. The vorticity of the central vortex and average cross-sectional vorticity are relatively low at the swirler outlet in both cases. Both of these statistics gradually increase to the maximum values near 20 mm downstream of the swirler outlet, and subsequently decrease. It is also found that the central vortex in the multi-swirler case is consistently greater than the single-swirler case. These results demonstrate the critical influence of boundary conditions on flow characteristic of swirling flow, providing insight into the difference of the experiments on testbed combustor and the full-scale annular combustors.     

金属聚合物复合材料的电树枝生长模拟

为了研究金属聚合物复合材料的击穿特性,在WZ模型的基础上建立了在绝缘聚合物介质中填充不同体积浓度的理想金属粒子的逾渗模型。利用计算机对放电通道的发展进行仿真,并对得到的仿真图形进行比较,研究了金属颗粒的体积浓度、下极板施加的电压、放电通道内的阈值电压和树点发展的概率指数对放电通道发展的影响。结果表明,金属粒子体积浓度越大,则放电树枝分枝越多。因此,填充金属颗粒可以明显地增强绝缘介质的导电性,其中逾渗阈值为0.6。下极板施加的电压越大,放电通道内的阈值电压和树点发展的概率指数越小,则放电树枝分枝越多,同时放电树枝生长过程中的积累损伤越大,该规律与实际放电情况相符合。     

叶片前缘旋流和常规冲击对比数值研究

为了寻求更好的叶片前缘内冷结构,对旋流冲击和常规冲击的流动和传热特性进行了数值模拟,对比研究了二者的涡流结构、传热强度、流动阻力、综合传热性能和热均匀性,研究了通道Re数和冲击间距对这些参数的影响。结果表明旋流冲击形成的旋涡有利于传热的增强和热均匀性的提高。在所研究的Re数（2×104~7.78×104）和冲击间距（3.3~5倍直径）范围内,旋流冲击与常规冲击相比平均传热增强18%~34%,增幅随Re数和冲击间距的增大而增大;流阻增大10%~26%,增幅随Re数和冲击间距的增大而减小;综合传热性能增强20%左右;热均匀性提高60%左右。