一种涡轮发动机加速控制规律设计的新方法

 提出了一种涡喷、涡扇发动机加速控制规律快速设计的新方法：在发动机稳态特性计算模型的基础上,通过额外增加转子提取功率,使得发动机稳态工作点（线）靠近喘振边界,在同时考虑燃烧室富油熄火边界、涡轮进口总温限制以及压气机喘振裕度限制的条件下,利用适当的控制规律描述形式并结合发动机工程研制中的经验,能够快速而准确地获得涡喷、涡扇发动机加速控制规律。对某型涡喷发动机加速控制规律的改进的计算结果表明,提出的加速控制规律的设计方法准确而有效。     

地面系留对直升机动力响应的影响

 建立了系留状态下直升机旋翼/机体耦合非线性动力学模型,无铰旋翼简化为当量铰刚性桨叶模型,假定机体是刚性体并受起落架和系留索的约束,系留索静态时松弛并只能承受拉力。采用数值仿真研究了系留对模型旋翼地面共振的影响,对初始扰动和旋翼转速对系统动力学行为的影响也进行了仿真研究。对于无系留的模型旋翼来说,在任何转速下没有出现不稳定现象;地面系留时系统会呈现稳定响应、极限环以及大幅值振荡等非线性动力学行为,大幅值振荡将使系留索、接头和支持结构承受破坏性动力载荷。     

金属橡胶减振器用于发动机安装减振的研究

 为减小发动机传递至飞机机身结构的振动,设计了金属橡胶减振器用于航空发动机安装。对该金属橡胶减振器进行了动力学建模研究,采用有限元技术对安装减振器前后的飞机全机结构进行了仿真分析,初步表明了该设计对结构频率影响较小,但能引入较大阻尼,降低响应水平。在理论分析基础上,进一步将设计制造的金属橡胶减振器安装于某型飞机,进行地面开车,实测了应用减振安装前后飞机的动力学响应。结果证明了发动机减振安装的可行性与有效性。     

多机并联火箭羽流流场及其底部热环境分析

针对某多机并联火箭羽流流场结构复杂、底部热环境极为恶劣,有可能导致发动机结构部件失效的问题,通过数值仿真对其飞行过程不同高度下的羽流流场及热环境进行研究,并与热环境实测结果进行了对比分析。计算结果表明:火箭低空飞行时,各发动机羽流互不干扰,随着飞行高度不断增加,羽流逐渐扩张并开始相互干扰,最后在箭体底部出现明显回流,最大热流在起飞时刻,与飞行实测值基本一致。出现回流之前,箭体底部主要受辐射热影响,随着回流出现,对流热流随之增大,但也远小于起飞时刻的热流峰值。计算得到的多机并联火箭羽流流场及其热环境分布对发动机舱外结构热防护优化设计具有一定的指导意义。     

Designing method of acceleration and deceleration control schedule for variable cycle engine

Studies show that different geometries of a Variable Cycle Engine (VCE) can be adjusted during the transient stage of the engine operation to improve the engine performance. However, this improvement increases the complexity of the acceleration and deceleration control schedule. In order to resolve this problem, the Transient-state Reverse Method (TRM) is established in the present study based on the Steady-state Reverse Method (SRM) and the Virtual Power Extraction Method (VPEM). The state factors in the component-based engine performance models are replaced by variable geometry parameters to establish the TRM for a double bypass VCE. Obtained results are compared with the conventional component-based model from different aspects, including the accuracy and the convergence rate. The TRM is then employed to optimize the control schedule of a VCE. Obtained results show that the accuracy and the convergence rate of the proposed method are consistent with that of the conventional model. On the other hand, it is found that the new-model-optimized control schedules reduce the acceleration and deceleration time by 45% and 54%, respectively. Meanwhile, the surge margin of compressors, fuel–air ratio and the turbine inlet temperature maintained are within the acceptable criteria. It is concluded that the proposed TRM is a powerful method to design the acceleration and deceleration control schedule of the VCE.     

Comparison of convergence time and positioning accuracy among BDS,GPS and BDS/GPS precise point positioning with ambiguity resolution

Precise point positioning (PPP) usually takes about 30?min to obtain centimetre-level accuracy, which greatly limits its application. To address the drawbacks of convergence speed and positioning accuracy, we develop a PPP model with integrated GPS and BDS observations. Based on the method, stations with global coverage are selected to estimate the fractional cycle bias (FCB) of GPS and BDS. The short-term and long-term time series of wide-lane (WL) FCB, and the single day change of narrow-lane (NL) FCB are analysed. It is found that the range of GPS and BDS non-GEO (IGSO and MEO) WL FCB is stable at up to a 30-day-time frame. At times frame of up to 60?days, the stability is reduced a lot. Whether for short-term or long-term, the changes in the BDS GEO WL FCB are large. Moreover, BDS FCB sometimes undergoes a sudden jump. Besides, 17 and 10 stations were used respectively to investigate the convergence speed and positioning errors with six strategies: BDS ambiguity-float PPP (Bfloat), GPS ambiguity-float PPP (Gfloat), BDS/GPS ambiguity-float PPP (BGfloat), BDS ambiguity-fixed PPP (Bfix), GPS ambiguity-fixed (Gfix), and BDS/GPS ambiguity-fixed (BGfix). The average convergence speed of the ambiguity-fixed solution is greatly improved compared with the ambiguity-float solution. In terms of the average convergence time, the Bfloat is the longest and the BGfix is the shortest among these six strategies. Whether for ambiguity-float PPP or ambiguity-fixed PPP, the convergence reduction time in three directions for the combined system is the largest compared with the single BDS. The average RMS value of the Bfix in three directions (easting (E), northing (N), and up (U)) are 2.0?cm, 1.5?cm, and 5.9?cm respectively, while those of the Gfix are 0.8?cm, 0.5?cm, and 1.7?cm. Compared with single system, the BDS/GPS combined ambiguity-fixed system (BGfix) has the fastest convergence speed and the highest accuracy, with average RMS as 0.7?cm, 0.5?cm, and 1.9?cm for the E, N, U components, respectively.     

带热障涂层固体发动机快烤特性有限元仿真

建立了发动机三维瞬态圆柱坐标的传热数学计算模型和发动机有限元仿真计算模型,通过导入快烤实验温度场数据,将仿真结果与试验结果进行对比分析,验证仿真模型的正确性；在药柱表面建立路径,记录每个时间点药柱不同位置的温度数据,并确定温度首先达到 550 ℃的危险点在药柱前端边缘处,得出涂层对危险点的延迟时间为 343.34 s；通过模拟 5 ℃/s和 10 ℃/s 2种不同升温速率的快速烤燃条件,对无涂层的对照组发动机和有涂层的发动机进行烤燃模拟,结果发现,升温速率为 5 ℃/s时,延迟时间为 182 s,升温速率为 10 ℃/s时,延迟时间为 191 s,延迟时间随升温速率的增大而增加,但总点火时间缩短。     

空天机复合循环推进技术新概念研究——液化空气循环在其中的应用

研究了空天机复合循环推进技术中的一个新概念——以液化空气循环为基础的SERJ组合发动机性能。计算了空气液化后分离为液氧和液氮后组合发动机在不同高度、不同飞行马赫数下的性能曲线,并考虑了液化空气量对组合发动机性能的影响。对计算结果的分析表明,液化空气循环虽然使组合发动机推力下降,但能使比冲有较大幅度的上升;液化空气量过大与过小均不利于进一步提高比冲性能,而是存在一个最佳值。     

二阶n次多项式自治系统的极限环的唯一性

主要利用文［１］中的变换，将下列二阶ｎ次多项式自治系统ｄｘｄｔ＝ｇ１（ｘ）＋ｈ１（ｘ）ｙｄｙｄｔ＝ｇ２（ｘ）＋ｈ２（ｘ）ｙ（＊）（其中，ｇ１（ｘ）＝∑ｎｉ＝０ａｉｘｉ，ｈ１（ｘ）＝∑ｎ－１ｉ＝０ｂｉｘｉ，ｇ２（ｘ）＝∑ｎｉ＝０ｃｉｘｉ，ｈ２（ｘ）＝∑ｎ－１ｉ＝０ｄｉｘｉ）变换成Ｌｉｅｎａｒｄ方程，再利用构造Ｄｕｌａｃ函数的方法和文［２］中的一个定理，得到了二阶ｎ次多项式自治系统（＊）的极限环唯一性的几个充分条件。     

液体火箭发动机燃烧室工作过程仿真软件──CAFILRE的设计与实现

描述了液体火箭发动机燃烧室内喷雾燃烧与流动过程仿真软件CAFILRE(Combus-tion and Flow in Liquid Rocket Engine）的结构和功能。CAFILRE程序是采用模块化方法编制和发展的二维通用软件，具有模拟发动机燃烧室内推进剂雾化过程、液雾蒸发过程、湍流混合与燃烧过程的能力。用此软件可以对发动机内部进行详细的性能分析和参数优化。