S弯收扩喷管流动特性数值研究

为了研究S弯收扩喷管的流动机理,数值模拟了不同喷管落压比（NPR）和S形收敛管道出口面积比（A₇₂/A₈）对S弯收扩喷管内流动的影响。结果表明：当S弯收扩喷管处于高度过膨胀状态时,随着NPR升高,非对称分离逐渐转变为对称分离,λ型激波转变为马赫盘结构,气动性能下降,推力矢量角减小;随着NPR继续上升,激波从喷管内移动到喷管出口边缘,并逐渐转变为膨胀波,气动性能上升,推力矢量角减小至0°后保持不变。在完全遮挡高温部件的低可探测准则的约束下,出口面积比A₇₂/A₈的变化主要对S弯收扩喷管收敛段的流动特性产生显著影响,体现在S弯收扩喷管内的局部加速及二次流分布。S弯收扩喷管的气动性能随着A₇₂/A₈增大而提高,但当A₇₂/A₈增大至1.8时,第一弯管道出口上壁面发生流动分离,气动性能显著下降。     

基于自适应差分进化算法的变循环发动机模型求解方法研究

为了降低传统迭代算法在求解变循环发动机非线性模型时对初值的依赖性,将模型的求解问题转换为求最小值的优化问题,引入差分进化算法进行模型的求解,并提出一种自适应差分进化算法(ADE)。ADE借助轮盘赌选择法,利用种群的进化经验可以自适应的选择最适合当前种群的差分策略与算法控制参数。针对变循环发动机四个典型工作点的模型求解问题,研究了标准差分进化算法(SDE)的控制参数对其性能的影响,获取了SDE在求解四个典型工作点时的最优控制参数组合,对比分析了ADE与SDE的性能差异,最后研究了种群规模对ADE性能的影响。结果表明：SDE在求解发动机模型时具有较好的鲁棒性,在求解不同工作点时算法的最优控制参数并不完全相同;相比于使用最优控制参数的SDE,ADE可以在不影响算法鲁棒性的情况下提升效率50%以上;减少ADE的种群规模会在提升算法效率的同时破坏鲁棒性。     

基于多代理模型的航空发动机建模及优化方法

为了进一步提高航空发动机建模及优化方法的性能,本文提出了一种基于多代理模型技术的建模及优化方法。本文首先提出了一种新的代理模型全局误差估计方法,以此建立了新的多代理模型建模方法。然后提出了一种组合模型预测偏差估计方法,以此发展了一种基于多代理模型技术的优化方法。6个不同维度及不同训练集大小的解析测试算例的结果表明,本文所发展的建模方法相较于现有方法精度更高,本文所发展的优化方法相较于经典代理模型优化方法算法收敛性更强。同时变循环发动机稳态性能建模及加速燃油控制规律优化实例表明,本文所发展的方法在处理实际工程问题时,依旧可以表现出良好的算法性能。     

2219铝合金变截面结构搅拌摩擦焊接工艺及组织特性

针对变截面结构产品,提出了一种变截面搭接结构搅拌摩擦焊接方法,通过加装辅助板将整条焊缝焊接方向上补偿为等厚度。焊接采用一次定位焊接+二次定位焊接+正式焊接的工艺方式,一次定位焊为预定位,二次定位焊保证辅助板与试片主体结构之间形成有效连接,正式焊保证形成完整的焊缝。焊缝表面成形良好,超声相控阵检测无超标缺陷。通过对力学性能的分析,变截面搭接结构处焊缝与非搭接处焊缝和常规对接焊缝的力学性能基本相同,平均抗拉强度均达到母材的70%以上,平均延伸率均在5.8%以上。变截面搭接焊缝焊核处晶粒形态为细小的等轴晶,靠近轴肩影响区部分的晶粒尺寸大于靠近焊缝根部的晶粒尺寸,受再结晶影响,焊缝两侧热机影响区处辅助板搭接界面消失。     

文氏管出口张角对旋流杯性能的影响研究

为了研究文氏管出口张角对旋流杯综合性能的影响,对不同文氏管出口张角的双级旋流杯开展了流量特性、下游流场和雾化性能试验,并借助仿真对试验结果进行了分析。结果表明:文氏管出口张角对旋流杯流量以及流量系数无显著影响。回流区外侧扩张锥面轴向速度随出口张角的增大先增后减。出口张角的存在可增大文氏管出口湍动能,强化两级旋流气体之间相互剪切作用进而改善雾化性能,存在一个最佳的角度(本文研究参数范围内,该值为56°)使得液雾平均粒径最小且液滴尺寸分布最均匀。拟合了关于文氏管结构的可用于预估双级旋流杯SMD值的模型公式,预估值与试验值吻合较好,相对误差小于20%。     

Design and implementation of rigid-flexible coupling for a half-flexible single jack nozzle

The aerodynamic design of a rigid-flexible coupling profile is the decisive factor for the flow-field quality of a supersonic free jet wind tunnel nozzle, and its mechanic dynamic features are the key for engineering implementation of continuous Mach number regulations. To fulfill the requirements of a free jet inlet/engine compatibility test within a wide simulation envelop, both uni-form flow-fields of continuous acceleration and deceleration are necessary. In this paper, the aero-dynamic design methods of an expansion wall and machinery implementation plan for the half-flexible single jack nozzle were researched. The profile control in nozzle flexible plate design was studied with a rigid-flexible coupling method. Design and calculations were performed with the help of numerical simulation. The technique of axial free stretching of the flexible plate was used to improve the matching performance between the designed elasticity profile and the theoretical one, and the rigid-flexible coupling structure was calibrated by wind tunnel tests. Results indicate that the flexible plate aerodynamic design method used here is effective and feasible. Via rigid-flexible coupling design, the flexible plate agrees with the rigid body very well, and continuous Mach number changes can be achieved during the tests. The nozzle’s exit flow-field uniformity meets the requirements of China Military Standard (GJB).     

A new steering approach for VSCMGs with high precision

A new variable speed control moment gyro (VSCMG) steering law is proposed in order to achieve higher torque precision. The dynamics of VSCMGs is established, and two work modes are then designed according to command torque:control momentum gyro (CMG)/reaction wheel (RW) hybrid mode for the large torque case and RW single mode for the small. When working in the CMG/RW hybrid mode, the steering law deals with the gimbal dead-zone nonlinearity through compensation by RW sub-mode. This is in contrast to the conventional CMG singularity avoidance and wheel speed equalization, as well as the proof of definitely hyperbolic singular property of the CMG sub-mode. When working in the RW single mode, the motion of gimbals will be locked. Both the transition from CMG/RW hybrid mode to RW single mode and the reverse are studied. During the transition, wheel speed equalization and singularity avoidance of both the CMG and RW sub-modes are considered. A steering law for the RWs with locked gimbals is presented. It is shown by simulations that the VSCMGs with this new steering law could reach a better torque precision than the normal CMGs in the case of both large and small torques.     

Numerical investigation on flow and heat transfer characteristics of supercritical RP-3 in inclined pipe

Numerical simulations of flow and heat transfer to supercritical RP-3 through the inclined tubes have been performed using LS k–e model embedded in Fluent. The physical properties of RP-3 were obtained using the generalized corresponding state laws based on the fourcomponent surrogate model. Mass flow rate is 0.3 g/s, system pressure is 3 MPa, inlet temperature is 373 K. Inclination of the inclined pipe varied from -90° to 90°, with heat flux varied from 300 k W/m~2 to 400 kW/m~2. Comparison between the calculated result and the experimental data indicates the range of error reasonable. The results of ±45° show that temperature inhomogeneity in inclined pipe produce the secondary flow in its cross section due to the buoyancy force. Depending on the strength of the temperature inhomogeneity, there will be two different forms of secondary flow and both contribute to the convective heat transfer in the pipe. The secondary flow intensity decreases when the inhomogeneity alleviates and thermal acceleration will play a leading role. It will have a greater impact on the turbulent flow to affect the convective heat transfer in the pipe. When changing the inclination, it affects the magnitude of the buoyant component in flow direction. The angle increases, the buoyancy component decreases. And the peak temperature of wall dominated by the secondary flow will move forward and increase in height.     

机场飞行区资源调度问题研究(二)：发展脉络与趋势

充分释放机场资源红利,发挥机场资源的最大效益,是空管、机场、航空公司、旅客和政府等航空运输各利益相关方的共同目标。本文聚焦机场飞行区资源调度的发展脉络与趋势问题,为飞行区资源调度问题研究系列之二。从明确资源总量、盘活资源存量、做强资源增量视角梳理飞行区资源调度的发展脉络,并对飞行区资源调度的一体化、高效化、智能化、协同化和绿色化发展趋势进行分析。研究成果旨在为机场运行管理理论与应用的可持续发展提供科学指引。     

前可变面积涵道引射器特性的试验与数值模拟

为了研究主、次流的进口总压比及出口背压对前可变面积涵道引射器(FVABI)工作特性的影响与流动掺混机理,采用试验与三维数值模拟方法对不同进口总压比下引射器工作性能及掺混流场随背压变化规律进行了分析。结果表明:标准k -ε模型用于引射器掺混流场的模拟具有较好的准确性;进口总压比越大,引射器总压损失越大;进口总压比不变,随背压增加,引射器总压损失先减小后增加;进口总压比不变,引射器在背压变化过程中存在总压损失最小点;背压减小时,引射器存在临界工况点,且进口总压比越大达到临界工况点的背压越大,可变涵道比的范围变窄;主、次流掺混过程主要集中在沿气流方向上x/l=03~06位置之间,在黏性力作用下动量、质量充分交换,沿流向截面速度径向分布趋于均匀。