液压能源管路系统振动主动控制的理论研究

对飞机液压能源管路系统的振动问题进行了探讨.提出一种基于振动主动控制(VAC)技术对飞机液压能源管路系统进行消振的方法,在手段上采用压电/压电致伸技术,以压电陶瓷(PZT)作为作动器,具有驱动力大、响应频率高和体积小等优点;控制方法上采用参数寻优的控制策略,它能始终能根据外界干扰因素的变化来调整控制参数.经过理论分析和仿真验证,证明其具有良好的自适应性和鲁棒性,在变转速和变负载情况下始终能保持最佳的消振效果.     

半浮区液桥自由面振荡特征

使用一套双路同步显微放大录像及图像处理系统,研究了夹角为90°的两个竖直剖面沿轴向不同高度液桥自由表面的位移振荡,得到轴向不同高度上的环向相位差,观测到在振荡周期内液桥表面轮廓线在不同时刻均不相交的特点。实验结果表明,液桥自由面振荡除具有径向扰动及轴向振荡变化外,还存在环向波动变化。根据实验结果,讨论了环向波动基本变化规律以及本实验在测量精度和测量误差方面存在的问题。     

Numerical simulations of water spray on flame deflector during the four-engine rocket launching

This paper aims to study on the cooling effect with two types of water spray nozzle on the flame deflector during the four-engine launch vehicle take-off. To accurately simulate the two-phase flow of the rocket gas with multispecies and the water spray, the three-dimensional compressible Navier-Stokes equations, discrete ordinates methods and realizable k-Ɛ turbulence model are used to establish the rocket supersonic plumes impact model. The Eulerian dispersed phase (EDP) model was used to simulate the water spray into the exhaust gas. The accuracy and effectiveness of the gas-liquid flow model are verified by a good agreement between simulation results and experimental data. On this basis, a series of numerical simulation studies under different water injection position are performed. The results show that the high temperature regions, along the axis of engines on the deflector plate, have no significant temperature decreasing effect by water spray from the nozzles mounted on the apex of the deflector, and the high temperature converts a large quantity of water into vapor near the plume boundary, which would decrease the flow conductivity. With the cooling spray nozzle fixed directly to the deflector plate, the temperature decrease effect is obvious and the effect of thermal shock on deflector plate induced by exhaust plume is reduced, so that it can prevent the flame deflector from thermal ablation. The study results provide indepth information and engineering guidance for designing the water spray systems and increasing the safety of the launch process.     

基于微型涡喷发动机热喷流的无源流体推力矢量喷管的控制规律

流体推力矢量喷管型面固定、活动部件少、结构重量轻，能够为高机动飞行器提供有效的飞行控制手段，但无源流体推力矢量喷管热喷流的偏转控制规律尚未完全掌握。为了推进无源流体推力矢量技术的实用化，本文设计研制了适用于微型涡喷发动机的耐高温喷管模型，对该喷管在微型涡喷发动机热喷流状态下的控制规律进行研究。利用非接触光学显示和测量手段——红外热成像拍摄和粒子图像测速（PIV）技术对主射流流动特性进行研究，获得流动矢量角随二次流控制阀门闭合度变化的控制规律；利用六分量盒式天平测力实验研究无源流体推力矢量喷管的力学特性，获得推力矢量角随二次流控制阀门闭合度变化的控制规律。研究结果表明：该构型喷管在微型涡喷发动机热喷流下主射流连续可控偏转，最大流动矢量角为-12.3°/12.3°，最大推力矢量角为-12.9°/12.8°，控制规律接近线性，不存在主射流偏转突跳问题。     

Flow mechanism between purge flow and mainstream in different turbine rim seal configurations

The rim seal is used to prevent mainstream ingestion to the gap between the vane of a turbine and its blade. In this article, the dolphin lip with a hook configuration and a large seal cavity with hook structures are designed based on the high-pressure turbine datum single shark lip rim seal configuration. The sealing effect and parameters of the flow field are measured by an experiment method and a numerical simulation is used to explain the mechanism. For three configurations, the effect of the leakage slot vortex on the efficiency of the seal and the influence of leakage vortex, generated by the interaction between purge flow and mainstream flow, are discussed in depth. The result shows that the reverse vortex formed by the dolphin lip rim seal with hook structure will increase the sealing efficiency. The seal configuration with a large cavity improves sealing efficiency to a greater extent than the datum structure. At different purge flow rates and with unequal seal structures, the purge flow produces three types of leakage vortices in the passage. Besides, the seal configuration with dolphin lip produces a Kelvin-Helmholtz instability at the interface of the purge and the mainstream flows at a low purge flow rate to induce new leakage vortex branches in the passage of the blade.     

幂律型流体撞击射流破碎特性直接数值模拟

凝胶推进剂的双股射流撞击雾化广泛应用于液体火箭发动机的燃烧室中,其破碎特征及雾化效果直接影响燃烧效率。为探究雾化特性的发展规律,采用直接数值模拟DNS方法,对射流速度为100m/s的剪切稀化非牛顿液体正交撞击产生的雾化特征、液体表面积、表面波、涡特性以及非牛顿特性开展研究。结果表明,射流下形成的雾化流场迅速扩张形成液膜,液膜两侧边缘破碎成大量的液丝与液滴,核心部分产生撞击波后在气体力的作用下逐步发展为带有凸起和褶皱的不稳定表面波,其撞击波波长最大可达2.46倍射流直径。液体表面积不断增长,但无量纲表面积总体呈现先下降再上升的趋势。气体中的涡量分布则分为有序附着区和无序爆炸区两类,并且涡量主要集中分布于气相区域。此外,射流撞击时产生强剪切使该液体内部的粘性系数下降,最低仅为初始粘性系数的0.3倍。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

考虑滑流影响的埋入式进气道气动特性分析与流动控制研究

研究滑流对埋入式进气道性能的影响机理对于发动机的稳定性具有重要意义。针对某型涡桨发动机 滑油散热器进排气道系统,基于 CFD技术建立系统的螺旋桨滑流与滑油散热器内流一体化数值模拟方法,进 行考虑滑流影响的滑油散热系统埋入式进气道气动设计仿真分析;针对埋入式进气道由于吸入边界层低能气 流导致通过散热器流量低的问题,设计4组涡流发生器进行主动流动控制。结果表明:滑流使得进气道中的气 流偏离,难以形成稳定漩涡,容易发生流动分离;而合理设计的涡流发生器可以有效改善埋入式进气道内流场 特性,并使通过散热器的流量提高12%。     

Numerical Simulation of Rotor Flow Field Based on Overset Grids and Several Spatial and Temporal Discretization Schemes

A numerical method based on solutions of Euler/Navier-Stokes (N-S) equations is developed for calculating the flow field over a rotor in hover. Jameson central scheme, van Leer flux-vector splitting scheme, advection upwind splitting method (AUSM) scheme, upwind AUSM/van Leer scheme, AUSM+ scheme and AUSMDV scheme are implemented for spatial discretization, and van Albada limiter is also applied. For temporal discretization, both explicit Runge-Kutta method and implicit lower-upper symmetric Gauss-Seidel (LU-SGS) method are attempted. Simultaneously, overset grid technique is adopted. In detail, hole-map method is utilized to identify intergrid boundary points (IGBPs). Furthermore, aimed at identification issue of donor elements, inverse-map method is implemented. Eventually, blade surface pressure distributions derived from numerical simulation are validated compared with experimental data, showing that all the schemes mentioned above have the capability to predict the rotor flow field accurately. At the same time, vorticity contours are illustrated for analysis, and other characteristics are also analyzed.