火星车双向抽展式转移坡道展开原理及特性分析

我国首次火星探测任务将于2020年实施,一步实现"绕""着""巡"的目标。着陆器在火星表面软着陆后,火星车能否沿转移坡道安全转移至火星表面,关系着本次任务的成败。从火星车转移坡道功能要求出发,提出了一种双向抽展式转移坡道方案,解决了大展出比、驱动共用、可靠展开等关键问题,对其展开原理及力学特性进行分析,并开展了模拟火星重力环境的展开试验,为我国火星车转移坡道设计提供参考。     

空间充气薄膜衍射成像结构的热力耦合分析

随着空间光学技术的发展,衍射成像系统成为空间光学领域的研究热点。提出了一种充气薄膜衍射成像结构设计方案,针对其在空间热载荷作用下的热力耦合效应开展研究。建立了充气薄膜衍射成像结构的热力耦合顺序分析框架,基于I DEAS和ANSYS软件二次开发技术,实现了热力耦合数值分析,得到了结构在轨运行时的瞬态温度场、热应力、热变形等。分析结果表明,充气支撑结构产生了较大热变形,但最大热应力远小于聚酰亚胺薄膜材料的抗拉强度,而镜面中心处没有出现较大的热变形响应,为充气薄膜衍射成像结构的防热设计提供了技术支持。     

A robust semi-analytic method to solve the minimum ΔV two-impulse rendezvous problem

A novel semi-analytic approach is developed to determine the minimum $\mathrm{\Delta }V$ for a two-impulse rendezvous and validated both empirically and analytically. A previously published closed-form $\mathrm{\Delta }V$ estimate and the Lambert minimum energy transfer is used to establish upper and lower bounds of the minimum $\mathrm{\Delta }V$ transfer between two orbits. These bounds, in conjunction with the bisection method, operate on a nonlinear radical cost function to guarantee linear convergence. This approach has several real world applications including a low earth orbit (LEO) to highly elliptical orbit (HEO), and a HEO to retrograde geosynchronous orbit transfer. The minimum $\mathrm{\Delta }V$ estimates are better than those reported in the existing literature, while run times improved as much as two orders of magnitude over a fixed time Lambert solver. All singularity cases were addressed such that any orbital geometry, including Hohmann and radial elliptic transfers, converged to the global minimum $\mathrm{\Delta }V$. This approach will work for both coplanar and non-coplanar 3D geometries for any orbit type.     

燃气源控制气流非稳态耦合传热问题研究(Ⅰ)--计算模型和方法

针对某燃气源控制气流与导热套环之间的非稳态耦合传热问题,建立了数学模型,并采用整体求解的方法进行求解,即把流体区域的流动和对流换热与固体区域的导热过程组合起来,作为一个统一换热过程来处理。为确保计算结果在物理上的真实性,采用“假密度”法求解以温度T为求解变量的能量方程。对于非稳态控制方程离散后的离散方程采用了PISO方法进行求解。     

超（近）临界压力航空煤油RP-3的拟过冷沸腾传热特性

为了研究吸热型碳氢燃料在新型飞行器中的再生冷却性能,采用电加热方式,在热流密度0.1-1.0MW/m2和质量流速500-1000kg/m2s条件下,小通道圆管内（D=1.6mm）研究了超（近）临界压力下（P=3MPa）航空煤油RP-3的拟沸腾流动传热特性。研究发现了超（近）临界压力航空煤油的拟过冷沸腾传热现象。拟过冷沸腾壁温变化特征和传热恶化特征与亚临界压力下的相应特征存在差异。超临界压力航空煤油传热区域划分为类液态强制对流传热区、拟过冷沸腾区和类气态强制对流传热区。拟过冷沸腾壁温和传热系数随流体温度增加而缓慢增加,起到传热强化的作用;拟临界温度区域,存在传热系数极小值点,燃料发生传热弱化;燃料温度大于拟临界温度,燃料处于超临界类气态,传热大幅强化。     

基于DPM的试验台导流槽喷水冷却数值研究

采用计算流体动力学(CFD)技术,对某型运载火箭动力系统试验时导流槽的热环境进行了分析。计算采用氢氧(H-O)单步燃烧反应模型,标准k-ε湍流模型获得燃烧流场,并采用离散相模型(DPM)模拟了试验台的喷水降噪系统和导流槽底部喷水冷却系统。随后,用经过校验的模型对某型号发动机试验台导流槽的设计参数进行了对比研究。结果表明:试验台的喷水降噪系统及导流槽底部的喷水冷却系统均对导流槽底部有冷却效果,两者同时工作时对导流槽底部的冷却有叠加增强效果;导流槽深度加大时或者喷水量加大时会对底部热环境的改善同样有增强作用。      

旋转盘腔稳态换热试验的时间相关性

在稳态换热试验中,试验没有达到稳定就测量会增大误差,常见工况中盘面平均努塞尔数Nu误差的半衰期为2500~2700s。为判断试验是否达到稳定或可测量状态,采用瞬态计算方法对旋转盘腔换热试验的稳定时间的判定方法进行了研究。数值计算结果表明:对于旋转盘腔换热试验,稳定时间较长。提供了一种通过试验精度判定稳定时间和可测时间的方法,试验前可以由固体非稳态导热的傅里叶数估算可测时间。建议试验过程中每隔一段时间观测传感器数值,观测时间间隔按对数规律确定,直到传感器数值不变以确定达到稳定状态。      

Experimental study on film cooling performance of imperfect holes

An experimental study is made to investigate the film cooling performance of imperfect holes due to in-hole blockage over a flat plate. A specifically pyramid-shaped element is used to simulate the in-hole blockage. Six in-hole blockage orientations (such as leading-inlet, leading-middle, leading-exit, trailing-inlet, trailing-middle and trailing-exit) and four blocking ratios (ranging from 0.1 to 0.4) are taken into considerations. Based on the experimental results, the influences of in-hole blockage on the film cooling effectiveness and discharge coefficient under typical blowing ratios are analyzed. It is confirmed that the in-hole blockage results in a reduction of discharge coefficient related to the perfect film cooling holes, especially for the leading-exit and trailing-inlet orientations with a big blocking ratio. However, in the view of film cooling effectiveness, the in-hole blockage shows complicated affecting roles. In general, except for the leading-exit orientation, the in-hole blockages produce detrimental influence on the film cooling effectiveness.     

带有冗余度的新型连续地月载荷转移系统动力学与能量分析

传统的连续地月载荷转移系统(CCPTS）存在可靠性低、转移效率差的问题。设计了带有冗余度的新型连续地月载荷转移系统(N-CCPTS）,其带有的一套冗余抓捕机构不但提高了系统的可靠性,而且可以运载载荷,将转移效率提高了1倍。计算和仿真结果表明,冗余机构对系统参数变化规律的影响是小量;在转移相同质量的载荷时,当椭圆轨道远地点的半径足够大时,N-CCPTS相比CCPTS更加节省能量。N-CCPTS可以为高效率的连续地月物资转移提供一种更加可行的方案。