HPM对伪码脉冲无线电引信的压制干扰效应仿真

为了对高功率微波作用于伪码脉冲无线电引信的干扰效果进行分析,建立了引信信号处理模型并进行了计算机仿真。仿真结果表明,在频率对准的情况下,当 HPM进入引信距离门对回波信号造成压制时,由于 HPM的信号频带较宽,覆盖了多普勒滤波器带宽,多普勒滤波器的输出信号幅度仍可达到启动门限电平,压制干扰无效。     

脉冲展开式飞网质量分布与展开稳定性优化

针对脉冲展开式飞网的展开稳定性问题，从网面质量分布角度开展研究。首先基于传递矩阵方法、集中质量法和反比例函数推导建立了较优的网面质量分布模型。然后结合遗传算法优化得到了网面最优的质量分布状态，并通过大量数值仿真和回归分析得到了网面质量分布经验公式。提出的网面质量分布模型有效降低了网面质量分布问题中的优化变量个数，提升了网面质量分布最优解的求解效率。网面质量分布最优解所对应的网面展开稳定性得到大幅提升，网面质量分布经验公式对应的网面展开状态与最优解对应的网面展开状态基本一致。结果表明，将网面质量分布模型和网面质量分布经验公式应用到脉冲展开式飞网将有效提升飞网的展开稳定性。     

Geometrical and electrical optimization of NS-SDBD streamwise plasma heat knife for aircraft anti-icing

Ice accretion on aircraft encountering supercooled water droplets in clouds poses great risks to flight performance and safety. With the aim of optimizing the newly developed streamwise plasma heat knife method for anti-icing, a parametric investigation is carried out in this work. The influence of the detailed voltage profile on the heating effects of a Surface Dielectric Barrier Discharge driven by Nanosecond Pulses (NS-SDBD) is investigated, and a comparison of the anti-icing performance among different configurations of streamwise plasma heat knife is made. The results show that columnar high-temperature regions produced by a multi-streamer discharge appear at small pulse rise time, but become diffuse as the pulse rise time increases. An optimal pulse rise time exists to provide a wide range and high value of temperature, which is found to be 150 ns for the setup in the present study. The influence of the pulse fall time is much weaker than that of the rise time. The range and value of the temperature decrease with increasing pulse fall time. A greater pulse width is found to improve the heating effect by increasing the discharge power. When a spanwise electrode is placed connecting the streamwise electrodes of the streamwise plasma heat knife at the airfoil leading edge, the anti-icing performance becomes poorer, whereas good performance is achieved when the spanwise electrode is at the edge of the streamwise electrodes. Based on this, a three-level configuration of the plasma heat knife is proposed, and its anti-icing performance is found to be much better than that of the original configuration.     

航天大功率电动伺服系统功率驱动设计及验证技术

针对运载火箭30 kW以上功率等级电动伺服控制驱动器的研制要求，设计了一种强环境适应的大功率绝缘栅双极型晶体管(IGBT)功率驱动模组。通过对火箭固体助推发动机工作环境分析，设计了基于光耦驱动器件的功率驱动与保护电路;为有效提升功率驱动模组在高压大电流工作时的可靠性，采用降低功率主回路杂散电感与IGBT有源钳位闭环控制相结合的方法，有效抑制IGBT在大电流关断时的电压尖峰;通过对动力电进行滤波处理，有效解决高压高频信号通过线缆传输时对控制驱动器内、外部的电磁干扰问题;通过IGBT功率驱动电路的单双脉冲测试及连续功率测试，有效验证IGBT功率驱动模组的高压驱动能力，为大功率电动伺服系统的可靠性提供技术支撑。     

新型凹入式螺旋结构增爆器的实验研究

本实验以脉冲爆震火箭发动机(简称PDREs)系统为实验平台,以液态航空煤油作为燃料,以压缩氧气作为氧化剂,以压缩氮气作为隔离气,分别对安装三种不同截面形式(半圆形、方形、三角形)的凹入式螺旋结构增爆器以及作为基准的Shchelkin螺旋结构增爆器进行了实验研究。实验结果表明,三种不同截面的凹入式增爆器均能有效强化爆燃向爆震转变(DDT)过程,在长径比为12.17的增爆器中均获得了充分发展的爆震波,实现了成功起爆。在流阻损失方面,半圆形凹入式螺旋结构表现出了最好的性能,其推力比Shchelkin螺旋的基准推力高出12个百分点。在多次实验过程中发现,凹入式螺旋结构比Shchelkin螺旋结构更不易烧蚀,工作可靠性更高。     

故障注入技术在飞行器非电系统中的应用进展

故障注入是一种基于试验的测评方法，是飞行器综合健康管理的重要组成部分，在提高飞行器的安全性方面具有重要作用。本文介绍了故障注入技术的基本原理，详细阐述了故障注入的各种实现方法在飞行器中的应用现状，重点分析了故障注入技术在飞行器结构、防热、液压、机械等非电系统应用中的关键技术以及存在的技术难点，并展望了该领域的发展。     

极区横向地理系空间稳定型惯导算法研究

针对地心惯性系和当地地理系的空间稳定型惯导系统导航算法在极区导航失效的问题,提出了适用于空间稳定型惯导系统的极区导航算法。该算法通过伪经纬网构建了横坐标系参考框架,建立了横向地理系空间稳定型惯导系统力学编排,并在此基础上重新推导了通用的误差模型。最后,通过极点附近区域与穿越极点区域仿真分析了算法的极区有效性。仿真结果表明该算法在极点附近区域解算的伪航向角误差小于3′,伪经度误差小于4′;在穿越极点区域解算的伪纵摇角、伪横摇角误差小于0.3′,伪航向角误差小于3′,伪东向、伪北向速度误差小于1m/s,伪经度、伪纬度误差小于4.2′。该算法克服了极区导航计算溢出、误差放大等问题,提高了系统的极区导航精度,能够满足极区导航要求。     

Adaptive feedback control of stability in an axial compressor with circumferential inlet distortion

The adaptive feedback control of stability with circumferential inlet distortion has been experimentally investigated in a low-speed, axial compressor. The flat-baffles with different span heights are used to simulate different distorted inflow cases. Compared with auto-correlation and root-mean-square analysis, cross-correlation analysis used to predict early stall warning does not depend on the distortion position. Hence, the cross-correlation coefficient was used to monitor the stable status of the compressor and provide the feedback signal in the active control strategy when suffering from different distortions. Based on the stall margin improvement of tip air injection obtained under different distorted inflow cases and the sensitivity analysis of cross-correlation coefficients to injected momentum ratios, tip air injection was adopted as the actuator for adaptive feedback control. The digital signal processing controller was designed and applied to achieve adaptive feedback control in distorted inflow conditions. The results show that the adaptive feedback control of air injection nearly achieves the same stall margin improvement as steady air injection under different distortion intensities with a reduced injection mass flow. Thus, the proposed adaptive feedback control method is ideal for the engine operation with circumferential distorted inflow, which frequently occurs in flight.     

往复节流式正脉冲发生器性能分析CSCD

在石油开采与钻探领域,脉冲发生器作为旋转导向系统井下信号传输系统的重要组成部分,提高压力脉冲幅值有助于提升旋转导向系列产品的市场竞争力。为了揭示其工作原理及提高压力脉冲幅值,基于计算流体动力学,利用用户自定义函数(UDF)、动网格技术、非牛顿流体模型,借助Fluent平台对往复节流式正脉冲发生器进行了动态数值实验。利用离散形式的动量方程将主阀体与电磁阀的被动运动转变为主动运动,选择适用于k-ε湍流模型的赫-巴非牛顿流体本构方程描述泥浆,提高了计算的收敛性与运动的可控性。基于非牛顿流体的流固耦合方法,更真实地模拟了脉冲器在井下工作过程。结果表明限流环内径越小或入口排量越大,则压力脉冲幅值与信号发生频率越大。     

Higher-order vibration of thick composite and sandwich plates based on an alternative higher-order model

The transverse stretching vibration of thick sandwich plates, which is attributed to largely different stiffness at the adjacent layers, is a challenging issue, and efficient approach for such issue is less reported in the published literature. Thus, natural frequencies corresponding to stretching vibration modes are generally neglected in engineering design, which might impact structural safety as frequencies of the exciting force are close to transverse stretching vibration frequencies. This paper proposes an alternative higher-order model for dynamic analysis corresponding to the higher-order vibration modes. The proposed model is classified in the displacement-based equivalent single-layer theory, as the number of displacement parameters in the proposed model is independent of the layer number. The continuity of displacements and transverse shear stresses can be fulfilled at the interfaces between the adjacent layers of structures. To demonstrate the capability of the proposed model, typical examples are analyzed by utilizing the proposed model, the three-dimensional finite element method and the chosen higher-order models. By comparing with the exact three-dimensional elasticity solutions, it is found that the proposed model can yield more accurate natural frequencies corresponding to the higher-order displacement modes than the selected models. Moreover, the factors influencing reasonable prediction of the higher-order frequencies are investigated in detail, which can provide a reference for the accurate prediction of the higher-order frequencies.