燃气推力矢量控制发动机内流场数值模拟

采用基于Favre平均的三维N-S方程,对燃气推力矢量控制发动机全内流场进行了数值仿真,研究了燃气引流、燃气二次喷射及与发动机内主流相互作用等复杂流动。研究结果表明,流场内包含复杂的涡系结构和波系结构,还存在着边界层与激波的相互干扰、自由剪切层、激波、膨胀波和大尺寸分离。通过数值模拟,对试验中的异常现象进行了定性分析,得出了与试验一致的结论。     

RAM的故障模型及自测试算法

通过对ＲＡＭ故障情况的全面、深入分析,建立了ＲＡＭ的功能故障模型。并在此基础上,提出一种全面、实用的故障自测试算法。该算法分三步完成测试：（１）测试ＲＡＭ中的固定为１（０）故障、固定开路故障、状态转换故障、数据保持故障及第一类耦合故障中的不相关耦合等故障;（２）测试第一类耦合故障中的相关耦合故障;（３）测试第二类耦合故障。对ＲＡＭ的故障注入试验验证了该算法的有效性。并将此算法应用于航空电子模拟器的ＢＩＴ（Ｂｕｉｌｔｉｎｔｅｓｔ）的设计中。     

电容式多次放电点火系统设计与试验

针对某型二冲程点燃式空气辅助缸内直喷发动机燃用柴油问题,提出了实现单电容连续多次放电点火的方法,研制了直流电容式多次放电点火模块,进行了多次点火功能性验证及点火能量测试.在此基础上,进行了环境温度为6℃下的冷起动试验及3000r/min小负荷性能试验,结果表明:在该环境条件下,采用5次放电点火策略能够使发动机起动成功,在小负荷工况下,增加点火次数有利于改善缸内燃烧,点火提前角在10°~20°之间时,4次点火对发动机动力性、燃油消耗率及排放性能改善比2次点火更明显,当点火提前角提前至30°后,其改善作用逐渐减小.      

基于SIMICS的ICP系统模块仿真技术研究

随着机载综合化航电系统的日益复杂,航电系统中软件的开发和验证也日益困难.通过研究基于SIMICS的仿真平台及二次建模技术,建立了综合核心处理机(ICP)中几种通用功能模块(CFM)的仿真模型,为系统软件和应用软件的开发、调试、测试、综合等提供了一套虚拟仿真环境,实现了软硬件协同开发,缩短了项目研制周期,提高了工作效率和软件质量,较大地提升了复杂机载软件产品的研制能力.     

环电流区能量离子分布特性研究

为了考察环电流区离子的分布情况,采用环电流粒子理论模式,对环电流中10-100 keV的离子进行了模拟研究.这个模式能够根据近地注入区外边界处离子的分布函数得出磁暴主相期间环电流中的主要成分H+,O+,He+3种离子的通量分布.计算结果分析表明,在其他条件相同的情况下,不同种类离子的通量分布的形态结构十分相似.电场强度对环电流离子通量的空间分布具有决定性的作用;晨昏电场强度越强,离子的通量越高;晨昏电场越强,环电流离子的内边界越接近地球.10keV的离子在电场相当弱的时候还是存在着连续的通量分布,但他们的形态和结构随着电场的变化有明显的变化.电场很弱时,离子分布主要集中于内外两个环带,离子通量在晨侧的更多一些,离子通量的最大值基本上是在比较靠近地球的环带上;随着电场的增强,离子分布的内外两个环带逐步合并,离子的分布逐渐靠近地球,通量分布的最大值也移动到了昏侧.环电流离子投掷角分布具有各向异性,投掷角在90°左右的时候,离子通量能达到最大值.      

Measurements of heat transfer and pressure in a trailing edge cavity of a turbine blade

 An experimental investigation is conducted to obtain the heat transfer and pressure drop data for an integral trailing edge cavity test section that simulates a novel turbine blade's internal cooling passage with bleed holes. Local heat transfer is measured on both the suction and pressure sides by a transient liquid crystal technique, while pressures at six positions are recorded by pressure calibrators. Moreover, flow characteristic and its effect on heat transfer are analyzed for conditions with or without bleed flow. The experimental results show that, in the cases with bleed flow, local heat transfer on the pressure side exceeds that on the suction side in the first and second channels. In the cases without bleed flow, in the first and third channels, local heat transfer on the suction side weakens whilst it increases significantly on the pressure side. For the second channel, non-bleed condition leads to a more balanced heat transfer distribution between the upstream and downstream channel. Besides, after the bleed holes are blocked, heat transfer in the first bend region on the suction side declines sharply, while the opposite phenomenon occurs for the second bend region on the pressure side. In both bleed and non-bleed cases, the total pressure of six measurement positions decreases continuously along the channel at the same Reynolds number and it promotes for higher Reynolds number. Among all the measurement points, under the same flow rate condition, the highest speed occurs at Position 5, which also shows the maximum difference between the total and static pressures. When the bleed holes are blocked, the total pressure at each measurement position appears to increase.     

二级轻气炮弹丸速度、质量和位置测量

二级轻气炮发射的氘冰弹丸的速度、质量和显示弹丸完整性的方法和所使用的仪器以及新开发的以波长编码、用光纤为传感器的弹丸进入位置的测量方法。     

气固两相透平叶片冲蚀特性的气动试验研究

在自行研制风洞中先后对应用较广的MCrAlY叶片涂层和2Cr12Mo-5叶片合金、钢丸表面强化试件在不同气流速度、颗粒冲角、颗粒性状、颗粒粒度的条件下进行了气动冲蚀试验。试验结果表明,无论是涂层还是合金,冲蚀率均随冲蚀颗粒的累积质量呈线性变化;由对比可知,其它条件相同的情况下,涂层在广泛的冲角范围内较合金的冲蚀率更小,表面的"烧结"特征,能减小叶片的冲蚀率;表面呈多棱的石英砂颗粒对试件的冲蚀程度强于带突圆球状的催化剂颗粒;在该试验范围内,相同材质的颗粒,粒度愈大,对试件的冲蚀率愈大;钢丸表面强化工艺兼有防冲蚀的能力。试验结果将为优化叶片选材、简化叶片维修技术、降低叶片维修成本提供有益的参考。     

A novel approach for predicting inlet pressure of aircraft hydraulic pumps under transient conditions

Cavitation caused by insufficient suction is a major factor that influences the life of aircraft pumps. Currently, pressurizing the tank can solve the cavitation problem under steady large-flow conditions. However, this method is not always effective under transient conditions (from zero flow to full flow in a very short time). Moreover, to apply and design other measures, such as a boost impeller, the suction dynamics during the transient period must be investigated. In this paper, a novel approach based on the pressure wave propagation theory is proposed for predicting the inlet pressure of an aircraft pump under transient conditions. First, a dynamic model of a typical aircraft pump is established in the form of differential equations. Then, the transient flow model of the inlet line is described using momentum and continuity equations, and the governing equations are discretized by the method of characteristics and the finite difference method. The simulated results are in good agreement with the results from verification tests. Further simulation analysis indicates that the wave velocity and transient time may influence the inlet and reservoir pressure as well as the size of the inlet line. Finally, solutions for upgrading the inlet pressure are discussed. These solutions provide guidelines for designing inlet installations.     

Transient simulation of regression rate on thrust regulation process in hybrid rocket motor

The main goal of this paper is to study the characteristics of regression rate of solid grain during thrust regulation process. For this purpose, an unsteady numerical model of regression rate is established. Gas–solid coupling is considered between the solid grain surface and combustion gas.Dynamic mesh is used to simulate the regression process of the solid fuel surface. Based on this model, numerical simulations on a H2O2/HTPB(hydroxyl-terminated polybutadiene) hybrid motor have been performed in the flow control process. The simulation results show that under the step change of the oxidizer mass flow rate condition, the regression rate cannot reach a stable value instantly because the flow field requires a short time period to adjust. The regression rate increases with the linear gain of oxidizer mass flow rate, and has a higher slope than the relative inlet function of oxidizer flow rate. A shorter regulation time can cause a higher regression rate during regulation process. The results also show that transient calculation can better simulate the instantaneous regression rate in the operation process.