Impact of bending dies with different friction forms on forming force and quality of tubes manufactured by free bending technology

In the 3D free bending forming system, the bending die can be designed either in a sliding type or rolling friction type. Bending die-based sliding friction type is often called normal bending dies; however, the bending dies-based rolling friction type includes bending die-based roller type and ball type in structure. In the current study, the impact of three bending dies on the forming force, and the bent tube quality was investigated. The obtained results showed that the tangential stresses and strains of the tubes formed by the bending die-based roller type were the smallest among the three bending dies. Besides, the spherical bearing force P_U was reduced drastically after using the roller type and ball type compared to the sliding friction type. Moreover, the uniformity of the wall thickness distribution of the tubes formed by the roller type and ball type was better than those obtained from the sliding friction type. In addition, the cross-section distortion rate was reduced by 2.8% using the roller type, and 1.8% using ball-type compared to the sliding friction type.     

基于分布式信源编码和感兴趣区域编码的干涉多光谱图像压缩

基于干涉多光谱图像特点和应用环境要求,提出一种基于分布式信源编码和感兴趣区域编码的干涉多光谱图像压缩算法。编码端通过关键帧预测出边信息帧,然后联合估计的边信息帧和插值分布的概率模型在编码端进行比特平面码率估计,最后采用基于率失真提升的感兴趣区域编码,调整图像不同区域的率失真斜率来进行更合理的码率分配。实验结果表明,该算法比传统算法更好地保护了多光谱图像的光谱信息。在不同压缩比的情况下,这种编码方式在干涉多光谱图像压缩系统中可获得较好的效果,算法复杂度低。     

双臂自适应夹具加工变形控制方法

在叶片加工过程中,由于叶片的薄壁和曲率多变特点,易受装夹、切削力和残余应力的影响而产生弯曲、扭转变形。针对该问题,本文提出了一种双臂自适应夹具加工变形控制方法,将加工过程中产生的变形逐层消除。首先,对叶片的变形成因进行分析;然后,通过对无应力装夹和加工应力释放原理进行研究,设计了一种可提供6个自由度的自适应装夹机构,并对该机构进行了工程设计和机构分析;最后,基于这种6自由度双臂自适应装夹机构,形成了本文提出的加工变形控制工艺,不需多次修复基准和更换机床,就可以逐层消除新产生的变形。实验结果表明,采用双臂夹具自适应加工变形控制方法,可以有效控制叶片加工过程中产生的变形,使叶片的轮廓误差降为原来的50%,提高了其加工精度。     

Passive inter-modulation scattering analysis of reflector considering contact nonlinearity

 Passive inter-modulation (PIM) is a form of nonlinear distortion caused by the inherent nonlinearities of the passive devices and components in RF/microwave system. It will degenerate the performance of communication system with broad-band channel and high-sensitivity receiver. Therefore, it is necessary to construct a model to simulate this process in order to predict the level of PIM. This paper is aimed at constructing some plate models with one-dimensional and two-dimensional contact nonlinearity sections illuminated by two-tone waves, and calculating the scattered field at a fixed-point in space using time-domain physical optics method. By taking fast Fourier transform (FFT), we get the spectrum of the scattered field and then analyze the generated PIM products. At the end of this paper, some numerical examples are presented to show the influence rules of the relative factors on PIM. The results indicate the variation of the level of PIM with the number of the nonlinear regions, the nonlinear spacing, and the incident power levels.     

周向总压畸变条件下多级轴流压气机失速首发级预测分析

基于多级轴流压气机的逐级特性,发展了1种预测周向总压畸变条件下多级轴流压气机失速首发级的方法。该方法结合平行压气机模型和级叠加计算方法,以进气畸变条件下多级轴流压气机某级的有效相对气流角达到稳定状态时该级的最大相对气流角为条件,进行多级轴流压气机失速首发级的预测分析。通过对J85—13发动机8级轴流压气机总压畸变试验数据进行模拟计算,预测出该轴流压气机畸变条件下的失速首发级。     

从角闪烁观点对被动测向中多径效应的讨论

多径效应是被动测向过程中客观存在的现象,基于其产生的物理机理可从角闪烁的观点出发来加以讨论。首先介绍了角闪烁的两种物理解释,其次对被动测向中的多径效应进行了一般的数学分析,说明了相应的统计模型,重点对低仰角时被动测向中的多径效应进行了特例分析,并进行了数字仿真。     

总压畸变在三级轴流压气机中的传递性能研究

介绍了一种计算进气畸变的方法.通过求解非稳态三维欧拉方程,计算压气机各截面气流参数分布.以74A三级压气机为例,进行了周向总压畸变传递特性计算,得到了压气机进口存在总压畸变时总压、静压、总温和流量系数在各截面上的分布规律,得出了畸变强度、畸变范围和畸变位置在轴向上的分布规律.      

系统级链路预算方法

计算地面站和飞行器之间的通信链路余量问题常依赖于简单的数学叠加法,但在实际应用中,复杂飞行器模型以及气候条件等干扰因素都容易造成天线方向图的畸变,从而导致链路预算不准.为了尽可能准确评估链路性能,提出了一种系统级链路预算评估方法.应用旋转变换矩阵,建立了姿态变化造成天线方向图相对变化的关系式.仿真得出装机后天线方向图畸变信息.根据相对变化量对方向图信息作数据挖掘.按全系统链路余量表达式计算变姿态情况下链路余量.评估了一种超短波通信天线与地面站天线间的通信链路性能,以及飞机降落时航向天线和航向台站之间的通信链路问题,表明该方法具有一定工程应用价值.     

基于实验的发动机插板式进气畸变压力谐振分析

某型涡扇发动机插板式进气畸变实验中,当插板升高到35%以上,进气截面各个测点畸变扰动出现约为32 Hz大幅振荡.用气流压力波动方程计算了进气道容腔谐振频率为34 Hz.表明该谐振是由插板与发动机之间的容腔引起的.不同转速和流量下,计算和实验的结果都基本稳定.由分析可知:150 Hz以下脉动压力是大幅稳定和周期性的.高频部分主要是小幅随机压力脉动,其速率和加速度变化比较剧烈.在发动机喘振前,谐振频率压力振荡能量大大增加,其它低频和高频成分能量迅速减少,形成典型的谐振型压力振荡.