离散粗糙元诱发边界层转捩的实验研究

针对直升机转子叶片模型表面离散粗糙元诱发边界层转捩问题开展了实验研究,分析不同雷诺数下粗糙元尺寸参数对转捩位置的影响。实验在中航工业气动院直升机转子叶片模拟装置进行,在模型转子叶片表面布置不同尺寸的离散柱状粗糙元,利用红外热像技术探测边界层转捩,并提出一种基于湍流／层流区域面积比的转捩位置判定准则,目的是实现边界层转捩位置自动识别,进而分析粗糙元尺寸参数对转捩位置的影响。实验转速为300至600 r／m,对应叶尖切向速度为25～40 m／s。实现了对旋转叶片边界层转捩位置的定量测量,通过实验验证,转捩位置判定算法正确可靠,初步得到了不同高度 DRE 诱发转捩位置与雷诺数之间的关系,随着粗糙元高度的增加,转捩位置逐渐靠前。     

基于等 Weber 数的结冰外形修正

由于设备条件的限制,在进行结冰风洞试验时,试验 Weber 数与目标 Weber 数往往存在差异,为了获得与目标 Weber 数对应的冰形,需要对试验结果进行修正。本文分析了进行 Weber 数修正的原因,提出了根据几何特征量进行结冰外形修正的方法,并以某超临界翼型为对象,对不同 Weber 条件下的结冰外形进行了仿真,研究了Weber 数变化对结冰的影响规律,在此基础上开展了基于等 Weber 数的结冰外形修正。研究发现：(1)Weber 数主要影响冰角特征,对水滴收集特性、结冰极限及驻点冰厚度影响较小;(2)存在一个敏感 Weber 数,低于敏感值时, Weber 数变化对结冰影响不大,当 Weber 数高于敏感值时,Weber 数变化对结冰有明显影响;(3)采用本文提出的冰形修正方法,能保证冰形的宏观轮廓与目标冰形一致,修正后的冰形能适量消除由于 Weber 数误差导致的冰形差异,提高试验的精度。     

跨声速串列转子失速机制的数值研究

为了解决跨声速串列转子的低裕度问题,就必须了解跨声速串列转子的流场结构与失速机制.设计了叶尖切线速度为450m/s,负荷系数为0.56的高负荷跨声速串列转子.基于数值模拟的结果,分析了该串列转子在0.5mm叶尖间隙下的叶尖流场结构与失速机制,并在此基础上分别探讨了叶尖间隙和前、后排叶片周向位置对串列转子特性的影响和失速机制的变化.结果表明:前排叶片的叶尖区域是 影响串列转子稳定性的关键;随着叶尖间隙的增加,串列转子的失速机制也发生变化,从前排叶片叶尖区域的尾迹与径向潜流堵塞后排叶片通道转变为前排叶片叶尖泄漏流堵塞;在较大周向相对位置(后排叶片压力面周向远离前排吸力面)的情况下,串列转子获得最好的效果,随着周向相对位置(PP)的增加,失速部位从后排叶片转移至前排叶片.      

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

扑翼飞行器非定常气动特性研究

为了研究复杂的非定常运动状态下扑翼飞行器翅翼的气动特性,针对自行研制的一种仿鸟扑翼飞行器建立了翅翼二维非定常空气动力学模型.基于该模型,通过用MATLAB编制计算升力系数和推力系数的程序,计算并分析了各运动参数对升力和推力特性的影响.结果表明,相位差对推力系数的影响较大,而升力系数随迎角的变化较快.     

加装吊舱对飞机操稳特性的影响及其尺寸界定

在机身等部位加装吊舱会导致飞机气动外形发生变化,为保证飞行安全,需要评估吊舱对飞机操稳特性的影响.通过CFD方法计算了某型飞机在加装不同尺寸吊舱下的气动特性,在原型机基础上通过增量法建立飞机飞行动力学模型,以必要的操稳特性指标为依据,评估加装吊舱对原型机操稳特性的影响,并结合飞行品质标准及飞机使用限制,给出了吊舱尺寸界限.结果表明,加装吊舱对原型机短周期模态、螺旋模态、定常直线平飞和俯仰拉升时的操纵有一定的影响,依据影响绘制尺寸界定区域图可为飞机改装提供依据.     

基于Kalman滤波的变体飞行器T-S模糊控制

针对变体飞行器的跟踪控制问题,提出了一种基于Kalman滤波的T-S模糊控制方法。考虑飞行器系统状态不可测,引入惯导数据作为辅助信息,利用Kalman滤波算法融合飞控信息与惯导信息实现状态估计。由于变体飞行器在不同变形结构下气动特性变化较大,为便于控制器设计,采用小扰动线性化方法得到飞行器在不同平衡点处的局部线性模型,并通过状态反馈方法设计局部控制器,局部线性模型和局部控制器通过模糊集和模糊规则聚合成一个连续光滑的全局T-S模糊模型和T-S模糊控制器。通过综合Kalman滤波器与T-S模糊控制器得到一个基于Kalman滤波的T-S模糊控制器。仿真结果表明,该控制器在变形过程中能够实现状态估计,保证飞机的跟踪性能。     

带非线性支撑的转子有限元模型求解方法

用数值方法研究了非线性支撑的柔性转子系统的动学行为,提出了一种将有限元与非线性支撑结合的模型和求解方法。利用有限元法(FEM)构建转轴和转盘部分的模型,通过矩阵进行组合;利用离散元方法对包含滚动轴承和挤压油膜阻尼器(SFD)的支撑部分进行建模,此部分包含4个单元,分别为轴承内圈、外圈、SFD内圈和支撑鼠笼。有限元部分和离散元部分通过轴端节点相连,仿真过程中轴端位移传递给非线性支撑部分,支撑部分通过位移计算得到的非线性力反过来作用于有限元转子轴端部分。为了耦合求解有限元转子和非线性支撑组成的数学模型,提出了一种综合的迭代求解方法,克服传统的有限元求解方法对轴端隐性非线性支撑的求解局限性。由于转轴部分采用了Timoshenko梁单元建模,对比与简单转子模型,可以考虑陀螺力矩和轴的柔性特征,更能体现非线性支撑对振动真实影响。在建立的20个轴单元的有限元转子模型中,非线性响应更多体现在靠近非线性支撑的节点1和节点21处,响应频谱中靠近轴端的节点能体现出滚动轴承的2倍和3倍变柔振动频率。     

转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

Water takeoff performance calculation method for amphibious aircraft based on digital virtual flight

Owing to the strong coupling among the hydrodynamic forces, aerodynamic forces and motion of amphibious aircraft during the water takeoff process, the water takeoff performance is difficult to calculate accurately and quickly. Based on an analysis of the dynamics and kinematics characteristics of amphibious aircraft and the hydrodynamic theory of high-speed planing hulls, a suitable mathematical model is established for calculating the hydrodynamics of aircraft during water takeoff. A pilot model is designed to illustrate how pilots are affected by the lack of visual reference and the necessity to simultaneously control the pitch angle, flight velocity and other parameters during water takeoff. Combined with the aerodynamic model, engine thrust model and aircraft motion model, a digital virtual flight simulation model is developed for amphibious aircraft during water takeoff, and a calculation method for the water takeoff performance of amphibious aircraft is proposed based on digital virtual flight. Typical performance indicators, such as the liftoff time and liftoff distance, can be obtained via digital virtual flight calculations. A comparison of the measured flight test data and the calculation results shows that the calculation error is less than 10%, which verifies the correctness and accuracy of the proposed method. This method can be used for the preliminary evaluation of airworthiness compliance of amphibious aircraft design schemes, and the relevant calculation results can also provide a theoretical reference for the formulation of flight test plans for airworthiness certification.