星载激光通信终端在轨机动对温度影响

对激光通信终端在轨瞬态温度变化开展了仿真,以期研究在轨机动的影响、热分析和热试验时机动模式的简化模拟。通过合理地分析与简化,建立终端的轨道热分析模型,准确模拟在轨机动,根据典型机动模式、外热流和涂层退化等因素设计了计算工况,得出了终端在轨运行过程中的温度场随时间和姿态变化规律。结果表明：不同机动模式下的温度变化存在差异,最大可达23.0℃,采用固定姿态或一维转动的简化热分析或热试验不能准确模拟实际飞行温度,甚至不能部分替代二维转动热分析或热试验;光学天线和反射镜的温度控制是制约终端工作的瓶颈,为终端设计合适的避光机动策略,可大幅度提高温度稳定度和均匀度。研究结果可以为光机电设备在轨机动策略的设计和改进提供参考。     

沥青基碳纤维热导率的间接法测量

文摘采用"四探针法"测定6种沥青基碳纤维单丝的轴向电阻率,通过3个经验公式计算得到其热导率,再将计算值与厂商公布值进行对比分析。结果表明:对于热导率600或300 W/(m·K)的碳纤维采用公式λ=1261/ρ计算得到的热导率值与厂商公布值最为吻合,而对于热导率在300~600 W/(m·K)的碳纤维采用公式λ=440 000/(100ρ+258)-295计算得到的热导率值与厂商公布值最为吻合。以此测试值为基础,建立了沥青基碳纤维单丝电阻率与其热导率的函数关系λ=152 740/(100ρ+22)-26,具有更强的普适性。     

未来太空气象预报系统一瞥

文章从几个方面对太空气象预报系统进行了简单的介绍,包括:当前太空气象预报系统的水平;模板预报方案实施细则;实施模板方案的难度与可行性。作者关心我国对太空气象预报系统的研究,为进一步降低航天器发射风险、提高航天器运行可靠性而献计献策。     

数值仿真技术在热真空试验中的应用

由于热真空试验中温度测点有限,且关键部位布置困难,不能反映试验过程部件整体和关键部位的温度结果,导致试验有效性和产品安全性难以判断。通过数值仿真技术对试验过程进行模拟,得到所有部件详细温度场,验证试验有效性与产品安全性;发现影响产品温度分布的因素,研究提高产品可靠性措施。通过对某天线热真空试验过程模拟,得到天线详细温度场,并发现产品散热板安装＂不紧密＂缺陷,是影响天线温度均匀性的＂关键点＂。     

高效空间应用燃料电池热能利用技术研究

首先介绍了空间应用燃料电池高效散热及温控技术。高精度控温主要是利用被动散热技术,将产生的热量快速传导至外部冷却介质,从而保证产热面的温度均匀性,实现电池稳定工作。通过嵌入式被动散热和双端散热的冷却方式,实现电堆内部最大温差小于5℃,换热系数达1000W/(m·K)。     

Interface Familiarity Restores Active Advantage in a Virtual Exploration and Reconstruction Task in Children

Abstract

Active exploration is reportedly better than passive observation of spatial displacements in real environments, for the acquisition of relational spatial information, especially by children. However, a previous study using a virtual environment (VE) showed that children in a passive observation condition performed better than actives when asked to reconstruct in reality the environment explored virtually. Active children were unpractised in using the input device, which may have detracted from any active advantage, since input device operation may be regarded as a concurrent task, increasing cognitive load and spatial working memory demands. To examine this possibility, 7–8-year-old children in the present study were given 5 minutes of training with the joystick input device. When compared with passive participants for spatial learning, active participants gave a better performance than passives, placing objects significantly more accurately. The importance of interface training when using VEs for assessment and training was discussed.     

航天飞行器热防护涂层研究进展

近年来,新研航天飞行器气动热环境往往具有高焓、高热流密度和长时间加热等特点,这促使防热材料的研制朝着低密度、高抗烧蚀、优良隔热等性能的方向发展。受自身材料类型的限制,无论烧蚀型(树脂基)或非烧蚀型(陶瓷基)防热材料都可以通过对烧蚀表面进行涂层处理的手段达到弥补材料性能短板,提高使用性能的目的。本文试图梳理、总结国内外近年来热防护系统用涂层材料的发展状况,探讨各自的优势和缺点,并提出了针对树脂基复合材料热防护涂层可能趋势的推测。     

考虑轨道摄动的外热流计算分析

为改进传统外热流算法未考虑外热流经多次反射后的吸收和国外商业软件未考虑轨道摄动及太阳矢量变化对外热流的影响等不足,重新定义了外热流角系数和外热流辐射传递因子,综合SGP4轨道模型和Gebhart方法,给出了考虑摄动等因素的辐射传递因子和轨道外热流计算模型,以及相应的计算流程。通过仿真分析论证了考虑多次反射及摄动等因素的重要性。     

Aerothermodynamic and stability analyses of a deployable re-entry capsule

Recent research projects, in the field of atmospheric re-entry technology, are focused on the design of deployable, umbrella-like Thermal Protection Systems (TPSs). These TPSs are made of flexible high temperature resistant fabrics, folded at launch and deployed in space for de-orbit and re-entry operations. In the present paper two possible sphere–cone configurations for the TPS have been investigated from an aerodynamic point of view. The analyzed configurations are characterized by the same reentry mass and maximum diameter, but have different half-cone angles (45° and 60°). The analyses involve both the evaluation of thermal and aerodynamic loads and the assessment of the capsule longitudinal stability. The aerothermodynamic analysis has been performed for the completely deployed heat shield in transitional and continuum regimes, while the longitudinal stability has been analyzed in free molecular, transitional and continuum regimes, also taking into consideration the heat shield deployment sequence at high altitudes.     

吊挂系统对波瓣混合排气系统气动热力性能影响

为了明确短舱中吊挂系统的堵塞效应对波瓣混合排气系统气动热力性能的影响,采用数值模拟的方法对包含吊挂的混合排气系统进行了定量研究。研究结果表明,受吊挂系统的影响,在波瓣混合排气系统混合段内,存在着一大尺度的回流区,其作用范围随吊挂长度的增加而增加。在性能参数方面,与未考虑吊挂系统时相比,考虑吊挂之后,虽然混合排气系统出口处热混合效率以及推力系数下降很小,最大降幅仅分别为0.017和0.01,但总压恢复系数却显著下降,最大降幅达到了0.03。此外,随着吊挂系统长度的变化,排气系统出口处的热混合效率、总压恢复系数以及推力系数变化幅度小于0.01,变化很小。