Al2O3/hBN自润滑复合材料的制备及显微结构分析

以Al2O3为陶瓷基体,hBN为固润滑组元添加剂,在N2保护下烧成,制得了Al2O3/hBN自润滑复合陶瓷,通过SEM、EDS、XRD等分析探讨了固润滑组元的引入量、添加助熔剂及常压和热压两种烧成条件下材料显微结构的变化。结果表明,hBN引入量为10%时已有足够的量均匀分散在基体中;相同烧成温度下,热压过程中施加的压力可以破坏hBN的卡片房式结构,伴随液相的出现有利于hBN的定向排列,获得了结构致密的自润滑复合陶瓷材料。     

聚苯乙烯粉末选择性激光烧结成型机理的研究

分析了聚苯乙烯粉末材料选择性激光烧结成型机理,并通过填充改性方法提高其成型性能.结果表明,添加无机填料可提高聚苯乙烯粉末材料烧结性能,而且,多种填料同时添加,效果更明显.     

高强Al-Cu-Li-X铝锂合金2A97三级时效工艺及性能研究

以新型高强Al-Gu-Li-X铝锂合金2A97为研究对象,通过拉伸试验研究两种三级时效工艺及其改型工艺对合金性能的影响.结果表明,含有δ′相二次析出过程的三级时效和含有δ′相回溶过程的三级时效处理合金的强度和塑性达到T6峰值时效水平,三级时效改型工艺由于增加变形使前者合金的强度升高,塑性降低,使后者的强度显著提高.三级时效和单级时效合金的主要显微组织有δ′相、θ″/θ′相和T1相.三级时效改型工艺由于增加变形促进δ′相析出和δ′相回溶,同时变形促进T1相析出,从而改变了主要强化相δ′相和T1相的数量.     

激光冲击残余应力场的有限元分析

建立模拟激光冲击残余应力场的非线性弹塑性有限元模型,预测AISI 304奥氏体不锈钢厚、薄靶材经激光冲击后表面以及内部的残余应力场分布.模拟过程中,考虑材料高应变率(106s-1)下的力学性能和激光诱导冲击波的精确加载,分析激光功率密度、激光光斑尺寸、激光脉宽、激光冲击次数、激光单面与双面冲击等激光冲击参数以及初始残余应力等因素对不锈钢靶材残余应力分布的影响.数值模拟结果与X射线衍射法测量值吻合较好.在有初始残余拉应力(250MPa)存在的情况下,激光冲击仍能使304奥氏体不锈钢靶材形成残余压应力层,说明激光冲击工艺可提高奥氏体不锈钢焊接构件的抗应力腐蚀开裂能力.     

无加力涡扇发动机二元喷管的红外辐射特性实验

对轴对称喷管和一组长宽比分别为1,4,8,12和16的二元喷管进行了红外辐射特性测试实验研究。喷管中的气流由主流燃气和次流空气组成,用以模拟涡扇发动机的喷管。得出了二元喷管的红外辐射强度的空间分布,并且将二元喷管和轴对称喷管的红外辐射强度进行了比较。      

吸气模式激光推进空气等离子体光谱

利用实验室自行研制的紫外预电离CO2激光器进行了激光等离子体实验,实验采用底面直径均为60mm,焦距分别为5 mm和10 mm的两种抛物面光船。介绍了激光等离子体光谱和明显的特征谱线,以及激光等离子体温度估计模型;分析了两种光船对激光等离子体的影响。实验表明:相同底面直径10 mm焦距光船产生的等离子体信号峰值和持续时间均略大于5 mm焦距光船;10 mm焦距光船产生的等离子体温度明显高于5 mm的,最大温度产生时间比5 mm光船要晚一些。     

The Genesis Solar Wind Concentrator Target: Mass Fractionation Characterised by Neon Isotopes

The concentrator on Genesis provided samples of increased fluences of solar wind ions for precise determination of the oxygen isotopic composition. The concentration process caused mass fractionation as a function of the radial target position. This fractionation was measured using Ne released by UV laser ablation and compared with modelled Ne data, obtained from ion-trajectory simulations. Measured data show that the concentrator performed as expected and indicate a radially symmetric concentration process. Measured concentration factors are up to ∼30 at the target centre. The total range of isotopic fractionation along the target radius is 3.8%/amu, with monotonically decreasing ²⁰Ne/²²Ne towards the centre, which differs from model predictions. We discuss potential reasons and propose future attempts to overcome these disagreements.     

Electrolytic Passivation of Nitinol Shape Memory Alloy in Different Electrolytes

The corrosion behavior of the nitinol alloy was studied in various corrosion media of different Cl–ion concentrations. The results demonstrate that the Cl–ion concentration has significant influences on the corrosion behavior of the nitinol alloy. In order to enhance the corrosion resistance, protective films were generated on the surface of the nitinol alloy by means of the electrochemical passivation method, for which five different electrolytic solutions were investigated. The surface analysis indicates full growth of all samples pas-sivated in the different electrolytic solutions with layers, however, showing different morphological features. Without any defects like micro-cracks and pores, the surface of the samples passivated in the molybdate solution turns out smoother and denser than those pas-sivated in other solutions. It is shown that the electro-chemical passivation will reduce Ni content but increase Ti content in the surface, reaching the Mole ratio of Ti:Ni=9.01:1 on the outermost surface. Potentiodynamic polarization test demonstrates that the samples electrochemically passivated in the molybdate solution present a significant increase in breakdown potential due to titanium enrichment on the outermost surface.     

联合应用现代优化方法与S2流面计算进行多级涡轮的气动设计

本文联合应用S2流面正问题计算和多级局部优化设计对某三级涡轮进行多级气动优化设计。优化联合采用人工神经网络和遗传算法,流场计算采用全三维粘性流N-S方程求解,计算网格采用H-O-H型网格,即入口段、出口段采用H型网格,叶片区域采用O型网格。通过优化,总效率提高1.1%,总体性能提高,达到设计要求。     

红外反射材料In（Sn）2O3（ITO）的微波吸收性能

测试7.7vol%和15.8vol%In(Sn)2O3(ITO)/石蜡在2~18GHz的介电谱。测定10vol%和20vol%In(Sn)2O3(ITO)/环氧树脂在2~8GHz的反射率。结果显示,ITO材料具有很好的介电损耗。当涂层厚度d=3mm时,两种涂层分别在4.51GHz和6.27GHz有-10.5dB和-14dB的反射率。理论值显示,15.8vol%ITO/石蜡复合材料在4.56~11GHz的反射率低于-10dB,有好的吸波性能。同时分析ITO的介电损耗机理。