TC2钛合金异型件热成形工艺研究

针对TC2钛合金异型零件的成形难题,设计了沿型面压边结构和中心顶出结构的2种成形工装,采用在不同温度下热成形的工艺方法.最后得出此种异型零件的适宜成形温度及成形工装结构.     

天问一号探测器高动态着陆惯导系统设计与试验

考虑到火星探测任务着陆过程动态变化大,稀薄大气环境下开伞会对探测器产生剧烈晃动,为此天问一号探测器研制了一套高动态着陆惯导系统,从硬件产品、使用时序到导航算法方面均进行了针对性设计,以适应着陆过程中的高动态环境.此外,为验证天问一号探测器高动态着陆惯导系统的性能,设计了模拟火星开伞工况的火箭弹高空开伞试验,结果表明该高...     

Variable Structure Control of Catastrophic Course in Airdropping Heavy Cargo

The mathematical model of a transport aircraft would be subjected to a sudden change when heavy cargo is dropped off in airdropping, which exerts serious influences upon the safety of the aircraft. A variable structure controller is specially designed for handling the airdrop process. The nonlinear system is linearized by input-output feedback linearization using differential geometry theories. On this basis, an inner loop system for velocity and attitude tracking control is designed by using the exponentially approaching rule of the variable structure theory. The whole flight control system is integrated with the outer loop flight altitude control. Digital simulation evidences the applicability of the system to potentially catastrophic course in airdropping heavy cargo and provides robustness against system parameter perturbation.     

基于FGN输入流的G/D/1排队模拟

传统的排队理论不适于分析高速网络表现出的自相似流量.通过实验仿真,主要考察平均等待时间和在队列分别为无限和有限情形下的队列尾部特征等参数,并对以FGN为输入流的G/D/1排队模型作了定性分析.结果表明在输入流的强度和方差基本相等且系统利用律大于某一阈值的情况下,队列平均等待时间随Hurst参数增大而显著增长.同时指出在相同的条件下考察队列尾部特征,具有有限队列长度的G/D/1排队模拟结果要远优于无限队列长度下的理论分析结果.      

任务教学法在Protel 99 se课程教学中的应用

任务教学法是一种以学生为中心,以任务为驱动的教学方法,它适用于实践性很强的prote199se课程.在一个个任务完成后,激发了学生自主学习的积极性,使学生在实践中学会了各种命令的使用,掌握了技巧,从而可以取得满意的教学效果.     

The effect of neglecting VLBI reference station clock offsets on UT1 estimates

Very Long Baseline Interferometry (VLBI) allows to monitor universal time (UT1) by conducting regular international experiments. Such dedicated observation networks are equipped with different hardware components, which require different processing strategies when the data are correlated. As the timing units at each stations are usually offset with respect to universal time (UTC) this effect should be considered during correlation processing. Thus, it is investigated how neglecting of these offsets theoretically impacts the estimation of UT1. Three different strategies for the proper handling of the timing offset will be discussed and their advantages/drawbacks will be pointed out. Moreover, it is studied how neglecting of these timing offsets affects UT1 time-series and how such a missing correction can be applied a posteriori. Although the discussed effect is for most of the UT1 experiments smaller than the formal error of the estimates, it is important to consider station clock offsets properly in next-generation VLBI systems, which are expected to improve accuracy of results by about one order of magnitude.     

TC4合金叶片热模锻过程的数值模拟

文摘为了生产出质量合格的叶片,针对TC4合金叶片的成形特点,为其制订了相应的热模锻成形工艺。同时采用基于有限体积的材料成形模拟技术,对TC4合金叶片热模锻过程进行了模拟,分析了坯料成形过程中的充填情况、应变场、应力场及终锻温度场的分布规律。模拟结果表明:锻件轮廓清晰,模具型腔充填完整,未出现充不满或折叠等锻造缺陷。实际生产出来的叶片经理化检测和外观检查,质量符合要求,制定的工艺方案合理,可以满足TC4合金航空风扇转子叶片的成形质量要求。     

CU-1型钇基重稀土对Be-Cu合金性能影响的研究

研究了CU-1型钇基重稀土对Be-Cu合金性能的影响。结果表明:Be-Cu合金经过微量CU-1型稀土的微合金化处理后,其显微硬度、耐磨性和耐腐蚀性均有不同程度的提高,热膨胀系数有所下降;随着稀土加入量的增加,Be-Cu合金的显微硬度逐渐提高,磨损量和平均腐蚀速率逐渐降低,热膨胀系数先减小后增大。     

固体发动机切割分离泄压过程分析

本文依据质点动力学和一维可压缩流体动力学原理，利用无限大容器的出流结果，在适当的简化假设基础上，建立了固体发动机切割分离泄压过程的数学模型，并对泄压过程和分离后的状态变化进行预测．通过比对分析试验容器的理论和试验结果，证明本文方法的误差在15％以内。     

航空发动机双层结构金属机匣的弹道试验

为研究航空发动机双层结构金属机匣在受叶片冲击时的包容性问题,利用滑膛炮试验系统对双层钛合金带不同间隙叠层靶板进行打靶弹道试验。通过28次有效的弹道试验发现:对比内层（迎弹面）、外层靶板厚度相同带间隙组合的试验结果,间隙越大靶板抗侵彻能力越差;对比不带间隙组合试验结果,内层较薄组合的抗侵彻能力强于内、外层厚度相同组合。采用商业有限元软件ANSYS/LS-DYNA对打靶试验进行了数值仿真,有限元仿真与试验结果吻合较好,并发现内层较薄组合的抗侵彻能力强于内层较厚组合,且两者均强于内、外层厚度相同组合;各个组合在没有间隙的情况下,弹道极限随叶片攻角增加而增加,但是速度曲线突增的攻角有所不同。无量纲靶厚决定了叶片冲击双层靶板的破坏模式。