GPS定位数据在海洋一号卫星中的应用与比较

简要介绍了海洋一号卫星星载GPS接收机的定位原理、流程和应用，探讨了一种在轨定位结果的确认和互验方法．借助于卫星工具包软件(STK)，利用NASA网站公布的HY-1卫星两行根数(TLE)进行卫星轨道推算，生成星下点位置，并与相应时刻星载GPS接收机实测数据得到的星下点位置进行比较，由此得到两种方法定位结果之间的偏差，用实际在轨数据验证了两者的位置符合程度．     

铝/ZN-1阻尼材料复合结构件的粘接技术研究

探讨了胶黏剂黏度、硬铝表面处理方式及硅烷偶联剂KH-560的使用方式等因素对硬铝板/ZN-1阻尼材料复合结构件的粘接性能的影响。研究表明：如果硬铝板表面采用砂纸打磨处理时，采用黏度较低的TC-1环氧树脂胶或者在黏度较高的J-22环氧树脂胶中添加2％的硅烷偶联剂KH-560可以获得优异的粘接效果；当硬铝板表面采用铬酸阳极化处理时，两种胶黏剂均能获得优异的粘接效果。     

测量机连续扫描控制系统设计

利用UCC1控制器作为核心,构建具有三维空间连续扫描功能的测量机控制系统的方法,并简要介绍了UCC1控制器的功能及控制系统硬件电路的设计。     

应用ART1神经网络仿真车间分组

阐述了ART1神经网络在制造单元设计过程中形成零件族的基本方法,并在基于MATLAB的软件平台上,利用其神经网络工具箱对生产过程中的实际情况进行了仿真和应用。     

Expectations for Infrared Spectroscopy of 9P/Tempel 1 from Deep Impact

The science payload on the Deep Impact mission includes a 1.05–4.8 μm infrared spectrometer with a spectral resolution ranging from R∼200–900. The Deep Impact IR spectrometer was designed to optimize, within engineering and cost constraints, observations of the dust, gas, and nucleus of 9P/Tempel 1. The wavelength range includes absorption and emission features from ices, silicates, organics, and many gases that are known to be, or anticipated to be, present on comets. The expected data will provide measurements at previously unseen spatial resolution before, during, and after our cratering experiment at the comet 9P/Tempel 1. This article explores the unique aspects of the Deep Impact IR spectrometer experiment, presents a range of expectations for spectral data of 9P/Tempel 1, and summarizes the specific science objectives at each phase of the mission.     

Deep Impact: Working Properties for the Target Nucleus – Comet 9P/Tempel 1

In 1998, Comet 9P/Tempel 1 was chosen as the target of the Deep Impact mission (A’Hearn, M. F., Belton, M. J. S., and Delamere, A., Space Sci. Rev., 2005) even though very little was known about its physical properties. Efforts were immediately begun to improve this situation by the Deep Impact Science Team leading to the founding of a worldwide observing campaign (Meech et al., Space Sci. Rev., 2005a). This campaign has already produced a great deal of information on the global properties of the comet’s nucleus (summarized in Table I) that is vital to the planning and the assessment of the chances of success at the impact and encounter. Since the mission was begun the successful encounters of the Deep Space 1 spacecraft at Comet 19P/Borrelly and the Stardust spacecraft at Comet 81P/Wild 2 have occurred yielding new information on the state of the nuclei of these two comets. This information, together with earlier results on the nucleus of comet 1P/Halley from the European Space Agency’s Giotto, the Soviet Vega mission, and various ground-based observational and theoretical studies, is used as a basis for conjectures on the morphological, geological, mechanical, and compositional properties of the surface and subsurface that Deep Impact may find at 9P/Tempel 1. We adopt the following working values (circa December 2004) for the nucleus parameters of prime importance to Deep Impact as follows: mean effective radius = 3.25± 0.2 km, shape – irregular triaxial ellipsoid with a/b = 3.2± 0.4 and overall dimensions of ∼14.4 × 4.4 × 4.4 km, principal axis rotation with period = 41.85± 0.1 hr, pole directions (RA, Dec, J2000) = 46± 10, 73± 10 deg (Pole 1) or 287± 14, 16.5± 10 deg (Pole 2) (the two poles are photometrically, but not geometrically, equivalent), Kron-Cousins (V-R) color = 0.56± 0.02, V-band geometric albedo = 0.04± 0.01, R-band geometric albedo = 0.05± 0.01, R-band H(1,1,0) = 14.441± 0.067, and mass ∼7×10¹³ kg assuming a bulk density of 500 kg m⁻³. As these are working values, {i.e.}, based on preliminary analyses, it is expected that adjustments to their values may be made before encounter as improved estimates become available through further analysis of the large database being made available by the Deep Impact observing campaign. Given the parameters listed above the impact will occur in an environment where the local gravity is estimated at 0.027–0.04 cm s⁻² and the escape velocity between 1.4 and 2 m s⁻¹. For both of the rotation poles found here, the Deep Impact spacecraft on approach to encounter will find the rotation axis close to the plane of the sky (aspect angles 82.2 and 69.7 deg. for pole 1 and 2, respectively). However, until the rotation period estimate is substantially improved, it will remain uncertain whether the impactor will collide with the broadside or the ends of the nucleus.     

TC21钛合金的微观组织对力学性能的影响

研究了两相钛合金TC21关于两种不同微观组织(片状组织和网篮组织)的拉伸性能、断裂韧性和疲劳裂纹扩展性能.结果显示:片状组织相比网篮组织有相近的拉伸强度,但塑性较差;两者的韧性相差不大,但增韧机理不同;网篮组织在中低速扩展区的扩展速率和片状组织几乎相同,但在较高速扩展区显示略低的扩展速率;加载方向对两种组织的疲劳裂纹扩展速率基本无影响;和其他钛合金类似,TC21在Paris区存在转折.     

Atmospheric reentry hemisphere prediction for prograde orbits using logical disjunction

A unique logic-based algorithm for atmospheric reentry hemisphere prediction is presented for spacecraft in low-eccentricity, prograde low Earth orbits at altitudes of 300 km and lower. Using two-line element (TLE) data for initial orbit conditions, coupled with coarse estimates for spacecraft aerodynamic characteristics, the algorithm relies on logical disjunction operations based on a dual analysis of histogram and two-weighted Gaussian probability density function (PDF) fits of predicted reentry latitude data. The algorithm requires the execution of a series of parametric simulations to determine the reentry hemisphere for variations in spacecraft aerodynamic coefficients and drag reference area. When implemented, the algorithm yields accurate hemisphere predictions on average 15 days from reentry as demonstrated by historical reentry cases from 1979 to 2018. All reentry cases were selected to demonstrate the algorithm’s ability to deliver accurate reentry hemisphere predictions for spacecraft with varying physical size and mass, and reentering during different periods of solar cycle activity.     

基于TC783A的三相电动机缺相保护电路的设计与实现

介绍用于三相电动机缺相保护装置的设计方法,采用集成芯片TC783A为核心元件实现,有效地解决三相电动机其他保护元件的局限性。具有快速切断控制回路电源的功能及缺相指示和相序指示,试验证明系统工作性能良好。     

DME Interference mitigation for L-DACS1 based on system identification and sparse representation

L-band digital aeronautical communication system 1 (L-DACS1) is a promising candi-date data-link for future air-ground communication, but it is severely interfered by the pulse pairs (PPs) generated by distance measure equipment. A novel PP mitigation approach is proposed in this paper. Firstly, a deformed PP detection (DPPD) method that combines a filter bank, correlation detection, and rescanning is proposed to detect the deformed PPs (DPPs) which are caused by mul-tiple filters in the receiver. Secondly, a finite impulse response (FIR) model is used to approximate the overall characteristic of filters, and then the waveform of DPP can be acquired by the original waveform of PP and the FIR model. Finally, sparse representation is used to estimate the position and amplitude of each DPP, and then reconstruct each DPP. The reconstructed DPPs will be sub-tracted from the contaminated signal to mitigate interference. Numerical experiments show that the bit error rate performance of our approach is about 5 dB better than that of recent works and is closer to interference-free environment.