基于仿真分析的压铆力预测模型

铆接是飞机结构机械连接的主要方式,压铆力作为影响铆接质量的重要因素,传统的计算方法通常是建立在体积不变的假设之上,且不考虑钉杆材料被压入钉孔部分的体积,导致模型误差较大。为此,依据仿真分析结果和铆钉材料的流动趋势,引入体积缩减系数来描述钉杆被压入钉孔部分的体积,建立压铆力预测模型,并与已有的试验数据进行对比,结果表明计算值与试验值的一致性较好,该模型可以用来预测铆接过程中压铆力的大小。     

The ‘Standard’ Sun Modelling and Helioseismology

The ‘standard’ solar model is based on a number of simplifying assumptions and depends on knowledge of the physical properties of matter in the Sun. Given these assumptions, the constraint that the model have the observed surface luminosity provides an estimate of the initial solar helium abundance. From helioseismic analyses further information can be obtained about the present composition, including a fairly precise measure of the envelope helium abundance and an estimate of the hydrogen profile in the radiative interior. It must be emphasized, however, that these inferences may suffer from systematic error arising from incomplete knowledge about the equation of state and opacity of the solar interior. This revised version was published online in June 2006 with corrections to the Cover Date.     

薄层碳纤维斜纹布层压板二次胶接试验研究

将复合材料薄板二次胶接技术应用在小型无人机机翼主承力结构上，对于降低机翼盒段的制造成本具有重要的工程应用价值。采用碳纤维斜纹布制2 mm 薄板进行单搭接结构拉剪试验，分析3 种不同型号的胶粘剂对该薄板的适配性以及胶层厚度和层压板铺层角度对二次胶接强度的影响，并通过ABAQUS 软件进行模拟验证。结果表明：使用SY-23B 环氧结构胶，胶层厚度为0.2 mm、铺层方式为［（0/90）］8 -［（0/90）］8 的结构件，胶接性能最优，结构剪切强度可以达到18.2 MPa，满足小型无人机受力盒段的胶接强度要求，二次胶接成形的机翼受力盒段具有轻质化、低成本的优点。     

先进战斗机强度设计技术发展与实践

新一代先进战斗机对机体平台的要求可以总结为轻重量、长寿命、多功能以及高承载。实现这个目标，除了材料与制造（新材料、新工艺、新结构/装配）的贡献，主机所强度设计/分析/验证技术也必须提升以适应先进战斗机的研制要求。本文阐述了强度设计团队围绕结构完整性要求，近年来在结构强度设计/分析/验证方面的研究成果、技术发展与设计实践，主要包括：面向新一代战斗机强度设计与验证的规范架构，基于多维包线的结构载荷筛选技术，基于统一模型的全机内力分析技术，复合材料整体化结构分析技术，高精度快速细节应力分析技术，内埋武器舱预紧舱门原理与强度设计，双曲面加筋壁板快速建模及声疲劳分析方法，结构故障预测与健康管理系统设计等。上述研究成果已成功应用于新一代战斗机机体平台研制。     

机载计算机安装架的强度计算

:叙述用有限元计算方法对特定的机载计算机安装架进行结构强度计算 ,内容包括静强度计算、结构自由振动分析和波形为后峰锯齿波的冲击载荷作用下的冲击响应分析。计算结果对安装架的设计具有重要的指导意义。     

Design and numerical investigation of swirl recovery vanes for the Fokker 29 propeller

Swirl recovery vanes（SRVs） are a set of stationary vanes located downstream from a propeller, which may recover some of the residual swirl from the propeller, hoping for an improvement in both thrust and efficiency. The SRV concept design for a scaled version representing the Fokker 29 propeller is performed in this paper, which may give rise to a promotion in propulsive performance of this traditional propeller. Firstly the numerical strategy is validated from two aspects of global quantities and the local flow field of the propeller compared with experimental data, and then the exit flow together with the development of propeller wake is analyzed in detail.Three kinds of SRV are designed with multiple circular airfoils. The numerical results show that the swirl behind the propeller is recovered significantly with Model V3, which is characterized by the highest solidity along spanwise, for various working conditions, and the combination of rotor and vane produced 5.76% extra thrust at the design point. However, a lower efficiency is observed asking for a better vane design and the choice of a working point. The vane position is studied which shows that there is an optimum range for higher thrust and efficiency.     

OPNET仿真软件在校园网中的应用

OPNET是目前一种很好的网络仿真工具。详细分析了较为通用的校园网,根据给定的校园网网络拓扑结构建立仿真中的网络模型,运用OPNET仿真软件对校园网内部简单的电子邮件传递服务和比较繁重的HTTP浏览进行了详细的研究。在网络模型的基础上,进行指定仿真数据的搜集工作,最后运行仿真,并根据产生的报告给出分析和总结。     

机翼/主起落架连接结构传力路线分析

在分析载荷传递的各种路线情况的基础上,通过改变主撑杆接头厚度和隔板厚度来观察连接结构各部分的应力状态,总结出其对传力路线的影响及其自身在连接结构中所处的地位,根据分析结果给出连接结构设计意见及建议。     

三轴仿真转台设计方法研究

针对航空、航天领域的半实物仿真关键设备-三轴仿真转台,重点从结构形式、电机选择、控制方式和控制算法等方面对其设计方法进行研究并提出相应的设计建议,对三轴仿真转台系统设计者具有一定的参考价值。