刀具磨损对TC11铣削表面粗糙度与残余应力的影响

为了研究TC11钛合金铣削加工过程中刀具磨损对加工表面质量的影响规律,设计了刀具磨损与铣削表面粗糙度、表面残余应力的试验。结果表明:TC11钛合金铣削加工过程中的刀具磨损可以分为:初期磨损、正常磨损、剧烈磨损三个阶段。当刀具处于"初期磨损"时,TC11铣削表面粗糙度随切削时间逐渐减小,铣削表面残余应力也呈减小趋势;当刀具处于"正常磨损"阶段时,铣削表面粗糙度和铣削表面残余应力都呈增加趋势,但增加的速度平稳;当刀具进入"剧烈磨损"阶段时,铣削表面粗糙度迅速增大,表面残余应力也较前两个阶段显著增加。另外,试验过程中的TC11铣削表面残余应力均表现为压应力。     

星用介质材料表面充放电效应试验研究

航天器表面介质材料易遭受表面充放电危害。利用30keV单能电子对几种不同的航天介质材料进行了表面充放电模拟试验,测量了不同电子通量辐照下的表面充电电位以及放电脉冲。试验结果表明,聚酰亚胺薄膜在接地处理不当时表面可充至千伏以上,易发生表面放电,且辐照强度越大,放电频率越高。表面镀铝的聚酰亚胺薄膜在不接地时,铝膜成为悬浮导体更加剧了放电的危害。而通过渗碳处理的聚酰亚胺薄膜,其良好的导电性能可有效抵御nA/cm~2量级电子的表面充电。聚四氟乙烯天线罩表面未进行防静电处理时,表面充电电位可达万伏量级,极易发生放电。     

Thermoelastohydrodynamic analysis of misaligned bearings with texture on journal surface under high-speed and heavy-load conditions

Hydrodynamic journal bearings are used to support the planetary gears in the transmission system of a Geared Turbo Fan engine, and they operate under severe working conditions, such as misalignment, high speed, and heavy load. Surface texture is regarded as an effective approach to improve mechanical properties under severe working conditions. However, the effects of surface texture on misaligned journal bearings under severe conditions have not been well studied. Therefore, a thermoelastohydrodynamic(TEHD) lubricating model with a textured and misaligned journal is presented in this study. Solid deformation, heat transfer between oil and the bearing, and heat convection between air and the bearing are considered in the model. The effects of cavitation and viscosity-temperature are also taken into account. The impacts of surface texture parameters and the misalignment angle on lubricating properties are investigated in the model. Results indicate that the bearing lubricating performance is greatly improved by optimal surface texture considering journal misalignment. The maximum oil film pressure and load-carrying capacity of a journal bearing increase with journal misalignment. Meanwhile, the oil film temperature increases sharply while considering misalignment.     

Experimental study of effect of post processing on fracture toughness and fatigue crack growth performance of selective laser melting Ti-6Al-4V

For Ti-6Al-4V, a titanium alloy increasingly used in aerospace structure, selective laser melting (SLM) is an attractive additive manufacturing technology, which is attributed to its complex construction capability with high accuracy and good surface quality. In order to obtain qualified mechanical properties, SLM parameters and post processing should be tailored for diverse service conditions. Fracture toughness and fatigue crack growth (FCG) behavior are critical characteristics for damage tolerance evaluation of such metallic structures, and they are affected by post processing technologies significantly. The objective of this study is to obtain the fracture toughness and fatigue crack growth behavior of Ti-6Al-4V manufactured by SLM, and to evaluate the influence of post-SLM thermomechanical treatment and surface machining. Fracture toughness and FCG tests were performed for SLM Ti-6Al-4V in three types of post processing status: as-built, heat treated and hot isostatically pressed (HIPed), respectively. Specimens with as-built and machined surface were tested. The microstructure and fractography were analyzed as well in order to investigate the relevance among manufacture process, microstructure and mechanical properties. The results demonstrate that as-built SLM Ti-6Al-4V presents poor ductility and FCG behavior due to martensitic microstructure and residual stresses. Both heat treatment and hot isostatic pressing improve the plane-stress fracture toughness and FCG performance considerably, while surface machining shows slight effect.     

LC4铝合金服役环境下点蚀形貌特征及其演变规律

为获取飞机LC4铝合金在服役环境下典型点蚀形貌特征,采用模拟服役环境的加速腐蚀实验环境谱对材料试件进行加速腐蚀实验,定义3个参数蚀坑深度H、蚀坑表面长度L、蚀坑表面宽度W为表征蚀坑形貌特征参量,跟踪测量典型蚀坑不同腐蚀年限下此3个特征参量数值,获取典型蚀坑形貌特征参量数据检测结果。在此基础上,对检测结果分别采用统计分析和分形理论方法进行数据分析,获取LC4铝合金同一腐蚀年限下和不同腐蚀年限下典型点蚀蚀坑的形貌特征及其演变规律。结果表明:同一腐蚀年限下,点蚀蚀坑形貌特征参量符合对数正态分布;随着腐蚀年限的增加,点蚀蚀坑形貌特征参量逐渐体现出明显的分形特征,蚀坑形貌逐渐趋向坑深度较浅、坑表面长度较长、坑表面宽适中的特征。     

铣削参数对7055-T6铝合金耐腐蚀性的影响

文摘研究了铣削工艺参数对切削力、表面粗糙度、轮廓与形貌、自腐蚀电位和电流密度的影响。结果表明:随着切削速度的增大,切削力与表面粗糙度呈现先增大后减小再增大的变化规律;随着轴向切深的增加,切削力与表面粗糙度都呈增大的趋势;铣削后刀面对已加工表面的挤压改善了铝合金的腐蚀性能;切削转速为4 000 r/min,轴向切深为0.25 mm时,加工表面耐腐蚀性能最优;在较大的轴向切深下,已加工表面易产生微裂纹,而导致腐蚀加剧。     

铣削加工参数对SiCp/Al复合材料表面粗糙度的影响

文摘SiC_p/Al复合材料在切削加工中存在严重的表面质量问题。本文设计单因素试验,采用硬质合金涂层刀具对SiC_p/Al复合材料进行铣削加工,研究了加工参数对表面粗糙度的影响。结果表明:表面粗糙度随切削速度的增大先增大后减小,随进给量、径向切深、轴向切深的增大而增大;使用较大的切削速度、较小的进给量和不大于4 mm的径向切深能获得较好的加工表面质量。     

GFRP铣槽加工铣削力及表面粗糙度研究

铣槽是复合材料较常用的机械加工形式之一。为研究玻璃纤维增强复合材料(Glass Fiber Reinforced Plastic,GFRP)铣槽加工中各加工参数对铣削力和表面粗糙度的影响,开展了以主轴转速、进给速度和轴向切深为因素的正交试验,研究铣削力和表面粗糙度的变化规律。并用Matlab软件对铣削力和表面粗糙度的试验数据进行回归分析,建立了铣削力和粗糙度的经验公式,最后通过试验验证铣削力和表面粗糙度经验公式的正确性。结果表明:轴向切深对铣削力影响最大,其次是主轴转速,进给速度对铣削力影响最小;主轴转速对粗糙度的影响最大,其次是进给速度,轴向切深对粗糙度的影响最小。试验结果与铣削力、表面粗糙度经验公式算得的数值对比,误差范围都在20%以内。     

原位自生TiB_2/Al复合材料磨削表面质量研究

原位自生TiB_2/Al复合材料具有密度小,比强度高,比模量大等特点,在航空航天领域具有广泛的应用前景。为探索原位自生TiB_2/Al复合材料的磨削加工性能,选用单晶刚玉SA砂轮、白刚玉WA砂轮和CBN砂轮在不同磨削参数下对TiB_2/Al复合材料进行磨削试验。首先研究了砂轮材质、转速、工件速度、磨削深度对工件表面粗糙度的影响规律;其次通过对工件表面形貌、磨屑形态、砂轮磨损的观测分析,探索了原位自生TiB_2/Al复合材料磨削表面成形机制;最后基于试验数据,给出了TiB_2/Al复合材料磨削工艺参数优选域。本研究可为颗粒增强金属基复合材料磨削加工提供基础理论支撑。     

表面组装技术和片状元件在空间应用的可能性

文章简单介绍了表面组装技术和片状元件的概况;结合卫星的特点,阐明了表面组装技术和片状元件在空间电子设备中应用的必要性和可能性。