激光重熔对喷射电沉积纳米结构镍涂层性能影响研究

采用喷射电沉积方法在45钢基体表面制备了纳米结构镍涂层,研究了激光重熔工艺对涂层性能的影响。用扫描电镜和X射线衍射仪对涂层表面形貌和晶粒尺寸进行分析,并对涂层做表面显微硬度测试和耐腐蚀性试验。结果表明:在优化的工艺参数下,喷射电沉积制备的镍涂层表面比较平整、结合较致密,由平均尺寸为13.7 nm的纳米晶颗粒组成,但涂层中仍存在一些孔隙及其它缺陷;经过激光重熔后,熔融区内的晶粒尺寸明显减小,涂层致密化程度有所提高并使涂层与基体由机械结合变为冶金结合,因此涂层的表面显微硬度和耐腐蚀性能得到明显的提高。     

喷管间距对双喷流啸音影响的实验

实验详细测量了完全膨胀马赫数范围为110~160、喷管间距为16到32倍喷管出口直径的超声速双喷流近声场,分析了两个喷流各自发出的啸音在近声场的相位关系,研究了喷管间距对双喷流耦合的影响。结果表明:对比单喷流,双喷流耦合啸音在A模态时,呈现出反对称或对称模式,在反对称模式下,喷管中间区域啸音强度减小,对称模式下,双喷流中间区域啸音强度略大于单喷流啸音;B模态时,两个处于摆动模态的喷流啸音在喷管中间区域同相而发生耦合,极大地增强了B模态的幅值,达到160dB;C模态的相位关系还需进一步研究。对比不同喷管间距下的双喷流近声场,发现喷管间距过小或过大均不利于B模态的耦合;喷管间距对C模态影响最大,当喷管间距变大时,C模态幅值及主导马赫数范围均增大。      

六喷管超音速引射器性能的理论分析和实验研究

对某一定尺寸的六喷管超音速引射器进行气动性能的实验研究。结果表明：随着主次流压比Ｐ＊ｐ／Ｐ＊ｓ增加，引射系数及修正引射系数下降；当引射系数增加时，混合管动量修正系数Ｋｍ下降，但主喷管流量系数μ变化不大。对上述工况进行理论计算的结果与实验数据符合良好。     

一种微型侧喷式压电合成射流器的设计

设计了一种侧喷型合成射流器,考察了射流器喷口结构尺寸对射流速度的影响,计算了不同喷口宽度下的动量系数,确定了喷口的最优尺寸,并在攻角为23°的NACA0015翼型进行了数值仿真模拟。结果表明,合成射流器可以有效的抑制边界层流动分离。同时设计了器件的加工工艺流程并完成了器件的加工。     

Experimental investigation and correlation development of jet impingement heat transfer with two rows of aligned jet holes on an internal surface of a wing leading edge

Extensive experimental studies on the heat transfer characteristics of two rows of aligned jet holes impinging on a concave surface in a wing leading edge were conducted, where50000 Rej 90000, 1.74 H/d 27.5, 66° a 90°, and 13.2 r/d 42.03. The finding was that the heat transfer performance at the jet-impingement stagnation point with two rows of aligned jet holes was the same as that with a single row of jet holes or the middle row of three-row configurations when the circumferential angle of the two jet holes was larger than 30°. The attenuation coefficient distribution of the jet impingement heat transfer in the chordwise direction was so complicated that two zones were divided for a better analysis. It indicated that: the attenuation coefficient curve in the jet impingement zone exhibited an approximate upside-down bell shape with double peaks and a single valley; the attenuation coefficient curve in the non-jet impingement zone was like a half-bell shape, which was similar to that with three rows of aligned jet holes; the factors,including Rej, H/d and r/d, affected the attenuation coefficient value at the valley significantly.When r/d was increased from 30.75 to 42.03, the attenuation rates of attenuation coefficient increased only by 1.8%. Consequently, experimental data-based correlation equations of the Nusselt number for the heat transfer at the jet-impingement stagnation point and the distributionof the attenuation coefficient in the chordwise direction were acquired, which play an important role in designing the wing leading edge anti-icing system with two rows of aligned jet holes.     

变攻角下被动射流旋涡对高速扩压叶栅性能的影响

对被动射流旋涡(PJV)控制高速扩压叶栅内的流动分离控制展开数值研究,并探究其在变工况条件下的适应特性。结果表明,PJV在设计攻角下可使叶栅总压损失系数降低5.2%,变攻角条件下的损失降低幅度最高可达7.8%,表明其具有较高的控制效率和良好的变工况适应特性。随着攻角的增大,吸力面分离位置提前,射流出口与分离区间的距离减小,PJV能够更为有效地促进附面层内低能流体与主流间的动量交换,使得壁面涡结构得到重新组织,并进一步影响通道涡、集中脱落涡等涡系结构的发展,从而推迟流动分离、减小损失。在综合考虑变攻角流场特性的前提下,应使PJV的作用位置位于分离区上游不远处,所研究的最佳射流位置位于叶片前缘上游40%轴向弦长处。      

零净质量射流的数值模拟

对零净质量射流致动器的流场和有零净质量射流时翼型的绕流流场进行了数值模拟,分析了动网格与几何守恒率、边界条件、湍流模型对零净质量射流致动器流场计算的影响,分析了零净质量射流的速度幅值和驱动频率对翼型增升效果的影响.研究结果表明,在复杂计算中可以对能动部件的边界作赋值处理;随着射流速度幅值的增加,翼型的平均升力系数和阻力系数都要增加;射流频率对升力的影响呈非线性.     

高温射流中粒子测速的脉冲激光显微照像技术

为了获得高温射流中微粒的速度,建立了一套显微照像系统。该系统由双脉冲YAG激光光源、粒子放大成像系统、图像接收系统组成。在采用显微成像技术、补偿式滤光技术、序列成像技术后,克服了喷射粒子直径小、流场发光强、温度高等困难,实现了对同一粒子的两序列照像,根据两幅序列照片,获得了粒子的喷射速度。对该系统的组成、原理及试验结果进行了介绍。     

几种关于附面层分离主动控制方法机制的概述

随着飞机和发动机设计性能要求的不断提高,流体的主动控制变得越来越重要,并显出不可替代的作用。流体主动控制方式通过小尺度、局部的能量注入,特别是通过对临界点附近的控制来改变全场的流动结构,并且能够对复杂的动态系统进行精确的相位控制,所以在近年的流动控制领域变得非常活跃。本文对合成射流、等离子体、电磁体积力这些主动控制方法及其机制进行了详细的介绍,并得出结论：相对于被动控制方式,主动控制方式具有明显的优势。     

Lumped element modelling of synthetic jet actuators

In this paper, a lumped element model of synthetic jet actuator is presented and used to predict the temporal variation of the jet velocity. Unlike the previous model reported in the literature, in this model the mechanical movement of the diaphragm is decoupled from the fluid phenomenon in the actuator cavity to allow the modelling of fluid mechanics aspect of the actuator to be investigated and validated separately. Furthermore, the “minor losses” occurring at the orifice exit is included and linked to the jet exit velocity profile. The results from this model are validated using the existing experimental data and CFD simulations. It is found that this model is capable of predicting the temporal variation of synthetic jets both in phase and magnitude when the actuator is operating away from the Helmholtz resonance frequency. Although the model fails to predict the correct phase information at the Helmholtz resonance frequency, it can still produce the jet peak velocity that is in good agreement with the experimental data. The lumped element model presented in this paper can be used to provide a reliable prediction of the jet peak velocity needed in the initial design of synthetic jet actuators for practical applications.