0.3 m低温风洞液氮供给系统研制

基于系统级的一维热流体模拟分析,建立了适用于研究分析0.3 m低温风洞液氮供给系统的数学模型,并开展了系统漏热、两相流及缓冲罐中液氮容积等流体动力学分析;在系统现有控制策略及试验数据的基础上,基于该数学模型开展了系统压力动态响应分析,获得了在阀门动态调节过程中管网压力的瞬态响应,计算结果与试验值的总体误差控制在10%以内。喷射压力一致化改造避免了阀间干扰,添加的回流管道消除了供给末端的两相流现象,使喷射压力控制精度达到1.1%,调节时间减少到23 s,实现了风洞总温快速安全调节和精确控制。     

脉冲爆震燃烧室出口燃气能量分布特性

为了提高脉冲爆震燃烧室出口燃气能量转换效率,采用数值计算方法,研究了带气动阀和爆震增强结构的脉冲爆震燃烧室出口燃气能量分布特性,结果表明:脉冲爆震燃气的膨胀过程先后经历一次膨胀、二次膨胀和过度膨胀3个阶段,单个周期内二次膨胀阶段的时间和能量占比最大;燃烧室出口燃气压力势能、动能、内能和能流密度的分布主要受燃气压力的影响,且变化规律与燃气压力一致;一次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的479%、259%、251%;二次膨胀阶段燃气增加的压力势能、动能、内能分别占单个周期的502%、576%、581%。     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian–Eulerian (ALE) approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation. A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished. In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact, a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces. In addition, the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method. Based on this method, fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained. Numerical results such as maximum Root Mean Square (RMS) drag, general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results. This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.     

Advances in critical technologies for hypersonic and high-enthalpy wind tunnel

Hypersonic and high-enthalpy wind tunnels and their measurement techniques are the cornerstone of the hypersonic flight era that is a dream for human beings to fly faster, higher and further. The great progress has been achieved during the recent years and their critical technologies are still in an urgent need for further development. There are at least four kinds of hypersonic and high-enthalpy wind tunnels that are widely applied over the world and can be classified according to their operation modes. These wind tunnels are named as air-directly-heated hypersonic wind tunnel, light-gas-heated shock tunnel, free-piston-driven shock tunnel and detonation-driven shock tunnel, respectively. The critical technologies for developing the wind tunnels are introduced in this paper, and their merits and weakness are discussed based on wind tunnel performance evaluation. Measurement techniques especially developed for high-enthalpy flows are a part of the hypersonic wind tunnel technology because the flow is a chemically reacting gas motion and its diagnosis needs specially designed instruments. Three kinds of the measurement techniques considered to be of primary importance are introduced here, including the heat flux sensor, the aerodynamic balance, and optical diagnosis techniques. The techniques are developed usually for conventional wind tunnels, but further improved for hypersonic and high-enthalpy tunnels. The hypersonic ground test facilities have provided us with most of valuable experimental data on high-enthalpy flows and will play a more important role in hypersonic research area in the future. Therefore, several prospects for developing hypersonic and high-enthalpy wind tunnels are presented from our point of view.     

Sensitivity analysis of flowfield modeling parameters upon the flow structure and aerodynamics of an opposing jet over a hypersonic blunt body

Implementation of an opposing jet in design of a hypersonic blunt body significantly modifies the external flowfield and yields a considerable reduction in the aerodynamic drag. This study aims to investigate the effects of flowfield modeling parameters of injection and freestream on the flow structure and aerodynamics of a blunt body with an opposing jet in hypersonic flow. Reynolds-Averaged Navier-Stokes (RANS) equations with a Shear Stress Transport (SST) turbulence model are employed to simulate the intricate jet flow interaction. Through utilizing a Non-Intrusive Polynomial Chaos (NIPC) method to construct surrogates, a functional relation is established between input modeling parameters and output flowfield and aerodynamic quantities in concern. Sobol indices in sensitivity analysis are introduced to represent the relative contribution of each parameter. It is found that variations in modeling parameters produce large variations in the flow structure and aerodynamics. The jet-to-freestream total-pressure ratio, jet Mach number, and freestream Mach number are the major contributors to variation in surface pressure, demonstrating an evident location-dependent behavior. The penetration length of injection, reattachment angle of the shear layer, and aerodynamic drag are also most sensitive to the three crucial parameters above. In comparison, the contributions of freestream temperature, freestream density, and jet total temperature are nearly negligible.     

端壁抽吸对压气机叶栅间隙泄漏流控制策略的研究

为了研究压气机机匣端壁抽吸对间隙泄漏流动控制的可行性和有效性,以高负荷压气机叶栅为研究对象,通过数值模拟方法对不同抽吸位置和抽吸流量率控制参数下的计算工况进行了对比和分析。研究结果表明:端壁抽吸可以直接地影响叶尖泄漏流的结构形态和存在形式,减弱叶尖泄漏流的强度和影响范围,进而提升压气机叶栅的性能;当抽吸槽覆盖范围包含叶尖泄漏流形成位置及稍靠后附近区域时,所对应的抽吸方案具有较好的控制效果,在0°攻角和0.5%的抽吸流量条件下前槽抽吸和中槽抽吸分别可获得7.04%和7.76%的叶栅总压损失增益;并且进一步研究发现端壁抽吸流量率存在上临界值,应针对不同攻角工况,在其相应的临界值范围内选择合理的抽吸流量,以达到用较小的吸气量实现对间隙泄漏流的控制。     

多Agent协调模型与算法在时隙分配中的应用

针对离场时隙分布式分配问题,阐述了航空公司和流量管理部门的博弈关系,建立了多Agent的博弈协调模型,提出了协调算法,并进行了算例分析.算例结果显示,应用博弈协调模型和协调算法,3个航空公司的延误时间分别为1 min、6 min和21 min,比RBS算法分配结果分别减少了10 min、6 min和2 min.算例结果说明多Agent的博弈协调模型及算法是可行的和有效的.     

网格拓扑对DLR-F6构型数值模拟的影响

基于TRIP3.0软件平台和多块结构网格技术,开展了控制方程和网格拓扑等因素对DLR-F6构型数值模拟的影响研究。数值计算采用与试验相同的参数,采用了RANS/TLNS方程,生成了O型和H型2种拓扑的粗、中、细网格进行模拟。分别从气动特性、压力系数分布曲线和表面流态3个方面对结果进行分析。通过与试验数据的对比表明,在模拟小分离流动时,采用H型拓扑网格和RANS方程模型,获得的计算结果会更为准确。     

重型模具在油压机上装卸作业的流程设计

根据工作中遇到的重型模具在油压机上装卸作业问题,设计了新的作业流程方案及其具体的实施措施,详细地介绍了流程实施过程中所使用工装的结构设计方案。