网络图中边集束优化问题

网络规模增大和复杂度提高造成的节点遮挡覆盖和边交叉阻塞等问题成为网络可视化研究的热点.针对网络中出现的视觉凌乱问题,以空间位置和群组关系为出发点,从网络中独立的边和群组两个层次,以边汇合的角度研究边集束技术,将网络中临近的边集聚成束以降低视觉复杂度,提出和改进了分段力导引算法(FDA)简化模型和群组边相容的网络图边集束模型.其中分段集束模型,提出以二次样条曲线表示网络边,通过样条控制点进行迭代汇聚的方法,实现了网络中边的集束;针对分段集束模型中部分连线过度弯曲问题,提出通过CNM聚类算法将网络进行群组划分,在群组结构的基础上对组内连线应用边相容原则,根据连线的匹配系数计算其集束程度的方法,网络图集束后曲线扭曲变形减少,曲线过渡更加平滑.选取国内航空网络作为案例,通过两种边集束模型进行网络图简化,分析结果表明,国内机场的群组结构具有地理属性的相近性,航空网络在整体上呈现出明显的十字脉络,东西走向和南北走向的航线分别汇聚集结成束,表现了航空网络建设在南北和东西方向的总体趋势.本集束简化算法适用性广,绘制的网络图具有良好的视觉效果和可读性.      

Grinding force and surface quality in creep feed profile grinding of turbine blade root of nickel-based superalloy with microcrystalline alumina abrasive wheels

Creep feed profile grinding of the fir-tree blade root forms of single crystal nickel-based superalloy was conducted using microcrystalline alumina abrasive wheels in the present study. The grinding force and the surface quality in terms of surface topography, subsurface microstructure, microhardness and residual stress obtained under different grinding conditions were evaluated comparatively. Experimental results indicated that the grinding force was influenced significantly by the competing predominance between the grinding parameters and the cross-sectional root workpiece profile. In addition, the root workpiece surface, including the root peak and valley regions, was produced with the large difference in surface quality due to the nonuniform grinding loads along the root workpiece profile in normal section. Detailed results showed that the surface roughness, subsurface plastic deformation and work hardening level of the root valley region were higher by up to 25%, 20% and 7% in average than those obtained in the root peak region, respectively, in the current investigation. Finally, the superior parameters were recommended in the creep feed profile grinding of the fir-tree blade root forms. This study is helpful to provide industry guidance to optimize the machining process for the high-valued parts with complicated profiles.     

Dynamics and control of spacecraft hovering using the geomagnetic Lorentz force

To achieve hovering, a spacecraft thrusts continuously to induce an equilibrium state at a desired position. Due to the constraints on the quantity of propellant onboard, long-time hovering around low-Earth orbits (LEO) is hardly achievable using traditional chemical propulsion. The Lorentz force, acting on an electrostatically charged spacecraft as it moves through a planetary magnetic field, provides a new propellantless method for orbital maneuvers. This paper investigates the feasibility of using the induced Lorentz force as an auxiliary means of propulsion for spacecraft hovering. Assuming that the Earth’s magnetic field is a dipole that rotates with the Earth, a dynamical model that characterizes the relative motion of Lorentz spacecraft is derived to analyze the required open-loop control acceleration for hovering. Based on this dynamical model, we first present the hovering configurations that could achieve propellantless hovering and the corresponding required specific charge of a Lorentz spacecraft. For other configurations, optimal open-loop control laws that minimize the control energy consumption are designed. Likewise, the optimal trajectories of required specific charge and control acceleration are both presented. The effect of orbital inclination on the expenditure of control energy is also analyzed. Further, we also develop a closed-loop control approach for propellantless hovering. Numerical results prove the validity of proposed control methods for hovering and show that hovering around low-Earth orbits would be achievable if the required specific charge of a Lorentz spacecraft becomes feasible in the future. Typically, hovering radially several kilometers above a target in LEO requires specific charges on the order of 0.1 C/kg.     

壁面吊挂清洗机器人碰壁缓冲问题研究

从机器人自动上壁及缓冲的需求出发,分析了机器人拉力形成的机理、碰壁的原因和过程.利用空气动力学原理,给出了拉力的计算方法,采用机器人物理样机进行实验,对计算结果进行了验证.在拉力的作用下机器人与壁面贴合,同时伴随碰撞,其间冲击能量的吸收由机器人裙边和支撑机构所构成的缓冲装置承担.前者还要保证机器人贴壁后的密封,因此刚度不宜过大,后者还要保证机器人在壁面上稳定行走,因此它的刚度又不宜过小.给出了缓冲装置刚度的确定方法及其在裙边和支撑机构上的分配准则,可用于工程分析.     

空间机器人在轨更换ORU的力/位混合控制方法

针对ORU在轨更换任务,首先推导了空间机械臂末端自由、末端与环境接触等情况下的动力学方程,并提出了相应的接触力计算方法;其次,改进了传统的R\|C控制方法,采用加权选择矩阵代替原有的选择矩阵,实现了力控制与位置控制之间的平滑切换;最后,开发了基于Matlab/Simulink的闭环控制仿真系统,该系统由多体动力学、接触动力学、轨迹规划、力/位混合控制、3D显示等模块组成。利用该系统开展了ORU转移与安装过程的闭环控制仿真,仿真结果校验了所提方法的有效性。     

多模式柔索驱动航天员训练机器人力控制

为解决长期在失重环境下生活和工作的航天员的康复训练问题,针对现有的航天员训练设备功能单一、训练效果不理想的现状,研制了多模式柔索驱动航天员训练机器人。基于模块化、可重构的机器人构型,通过机器人模拟重力环境的负载特征,把相应的载荷施加到人体上,实现航天员在失重环境下进行跑步、卧推和负重深蹲等体育训练,帮助航天员减轻或者克服空间适应综合征带来的不利影响;在此基础上提出一种机器人双闭环力控制策略,人机跑步训练实验结果表明,本文研制的多模式航天员训练机器人构型合理,控制策略有效,可以辅助在失重环境下生活和工作的航天员开展体育训练。     

离心力场下扩散射流火焰的特性

以直段空腔和弯曲空腔为研究对象,在相同的初始条件下试验了两者之间火焰传播的特性,研究了强离心力条件下的扩散射流火焰特性.通过比较分析,在弯曲空腔中离心力场的影响下,扩散射流火焰受到浮升力的作用,以"焰泡迁移"的方式在主流中传播,加快了火焰传播速度,削弱了横向气流的干扰作用,使扩散射流火焰顺利地与空气掺混反应,增加了其在横向气流中的穿透深度.      

无人机气动力地面车载测试系统

介绍了中国航天空气动力技术研究院开发的一种用于测量全尺寸无人机气动力的地面车载测试系统（GTV）。车载测试系统采用一辆中型卡车进行相关改造,将试验无人机机身安装在其顶部,通过汽车牵引能够达到40km/h的速度。一套专用的测试天平系统和数据采集系统用于记录试验中无人机产生的升力、阻力以及俯仰力矩等数据。主要介绍测试天平系统的设计,数据采集测试系统,测试方法和试验结果。多元静态原位校准加载结果表明天平测试系统输出信号线性度以及重复性较好。动态校准试验采用一副定常展弦比6的机翼进行,试验结果与已知的风洞试验数据进行了比对。车载测试系统试验结果的升力和俯仰力矩数据不同车次之间重复性较好,并且与风洞试验数据基本一致。但阻力数据的离散度要比风洞试验时大得多,并且试验结果比风洞试验时偏小一些,试验证明地面车载测试系统的阻力测量难度较大。     

箱梁颤振过程中旋涡的演化规律及气动力的变化特性

利用粒子图像测速技术（PIV）观测了箱梁颤振过程中模型周围流场的旋涡特征,以模型扭转振动位移作为参考信号,采用相位平均的方法研究了旋涡规律性演化对模型周期性振动的驱动作用。风速较低时,箱梁振幅很小,其尾部风嘴附近上侧的旋涡尺度也很小,不易观测到,而下侧的旋涡尺度较大,其形状接近于圆形。当风速接近颤振临界风速时,箱梁振幅明显增大,并且模型尾部风嘴上侧的旋涡尺度也显著增大,达到与下侧旋涡尺度相匹配的程度,模型尾部风嘴上下侧旋涡的交替作用主导了结构振动直到模型振动发散。基于流固松耦合的计算策略,采用计算流体动力学（CFD）的数值方法模拟了箱梁颤振临界状态下的绕流特性,结合正交特征分解（POD）的方法研究了模型颤振时刻表面压力的空间分布特征,通过分析发现在颤振过程中箱梁表面波动压力的主控成分向迎风侧风嘴漂移。     

仿昆扑翼飞行器的翅膀惯性力分析

用理论模化和仿真试验相结合的方法,研究了昆虫翅膀扑动产生的惯性力和惯性力矩.在昆虫扑翼飞行运动的仿生模拟基础上,研究了翅膀扑动过程中拍动幅度、拍动加(减)速周期、平动迎角和翻转加(减)速周期4个振翅运动参数对翅膀惯性力(矩)的影响.研究表明:微小尺度昆虫高频扑翅产生的惯性力幅值与气动力的幅值大致相当;昆虫翅膀的弦向转动惯量比展向转动惯量近似高一个数量级;翅膀拍动惯性力矩的影响远远高于翅膀转动惯性力矩的影响,而转动惯性力矩是可以忽略不计的;只要翅膀的拍动是对称的,就可认为翅膀的扑动是近似对称的;如果翅膀拍动对称的同时转动对称,就可认为翅膀的扑动是严格对称的,此时翅膀惯性力可以忽略.