基于实测星载原子钟数据的脉冲星守时方法

利用脉冲星估计星载原子钟钟差是实现卫星自主守时的途径之一。为充分分析基于脉冲星的自主守时系统性能，利用实测的星载原子钟钟差数据和中子星内部组成探测器(neutron star interior composition explorer, NICER)的PSR B1937+21脉冲星的观测数据，对比分析了星载原子钟和脉冲星的误差特性。设计了脉冲星守时系统框架和星载原子钟钟差估计方法。以实测的星载原子钟钟差数据为基础，计算分析了脉冲星守时系统的性能。计算结果表明，若脉冲星的脉冲到达时间（time of arrival, TOA）解算精度为1 μs/30 d，则原子钟钟差估计精度可达到优于1 μs的水平，初步验证了脉冲星守时系统的可行性。     

Passive localization by a single moving observer using TOA only with unknown SRI: Observability analysis and algorithm

Passive localization by a single moving observer using Time of Arrival (TOA) only with an unknown Signal Repetition Interval (SRI) is investigated in this paper. Observability analysis is performed first. The observability condition for uniquely determining the emitter position and SRI is derived. The conditional Cramer-Rao Lower Bound (CRLB) is also analyzed. It is found that the ambiguity of the SRI integer of the first TOA does not affect the theoretical estimation precision of the emitter position and SRI. A Reference-Fixed Differential TOA (RFDTOA)-based Iterative Maximum Likelihood Estimator (IMLE) is proposed, which only needs O(M) computational operations. Theoretical analysis and simulation results show that the Mean Square Error (MSE) of the proposed algorithm could attain the CRLB with moderate Gaussian measurement noise.     

基于锥形压入的材料力学性能测试方法研究

通过压入测试以获取工程服役结构、小型构件和焊接结构焊缝过渡区的材料单轴本构关系参数,且根据材料本构关系参数来估算材料的压入硬度对于工程设计和安全评估有重要意义.对于幂律材料,本文依据锥形压入试验原理和弹塑性接触有限元分析(EPFEA),揭示了不同锥角的锥形压头其压入能量比与屈服应力之间存在线性关系,提出了基于能量原理预测金属材料本构关系部分关键参数(弹性模量、屈服应力和硬化指数)的CR-EMI (Constitutive Relationship based on Energy Method of Indentation)方法.同时,基于此种线性关系提出了由Hollomon本构关系模型参数预测硬度的H-EMI(Hardness based on Energy Method of Indentation)方法.通过对多种金属材料进行压入试验和有限元分析,验证了CR-EMI方法和H-EMI方法的有效性与精确性.     

基于FFT含有饱和环节的非线性等效系统的方法研究

基于快速傅里叶变换(FFT)方法,对系统的输入和输出信号进行快速傅里叶变换,对含有高次谐波的输出信号进行滤波,得到期望主频率的傅里叶频谱,然后进行傅里叶反变换,求得在各主频率下的幅值和相位.利用MATLAB中的非线性最小二乘拟配方法得到含有非线性环节的飞机纵向飞行控制系统的频域等效线性模型.这种方法也为含有非线性环节的飞机纵向飞行控制系统的飞行品质评估提供了一种可行的方法.     

Form-finding methods for deployable mesh reflector antennas

Deployable high-frequency mesh reflector antennas for future communications and obser- vations are required to obtain high gain and high directivity. In order to support these new missions, reflectors with high surface accuracy are widely required. The form-finding analysis of deployable mesh reflector antennas becomes more vital which aims to determine the initial surface profile formed by the equilibrium prestress distribution in cables to satisfy the surface accuracy requirement. In this paper, two form-finding methods for mesh reflector antennas, both of which include two steps, are pro- posed. The first step is to investigate the prestress design only for the cable net structure as the circum- ferential nodes connected to the supporting truss are assumed fixed. The second step is to optimize the prestress distribution of the boundary cables connected directly to the supporting truss considering the elastic deformation of the antenna structure. Some numerical examples are carried out and the simulation results demonstrate the proposed form-finding methods can warrant the deformed antenna reflector surface matches the one by design and the cable tension forces fall in a specified range.     

GJB5000A软件测量指标的研究与应用

讨论了型号软件GJB5000A的测量与分析过程,采用系统论方法,阐述了三级测量目标、测量项的确定,对测量指标存在的涌现性进行了探讨,在此基础上举例说明如何在三级贯标项目中进行软件测量指标的选取。通过将近一年时间的GJB5000A项目实施,证明了测量指标选取有效性,以及测量指标存在的涌现性命题。     

推进剂供应管道的集中参数近似模型研究——模态近似模型

提出了用模态近似法建立分布参数湍流管道的集中参数近似模型的新方法,发展了适用于水力和绝热气体湍流管道的两种模态近似模型：Ｉ－Ｒ－Ｃ模态和等效层流模型。模型中考虑了频率相关摩擦损失。利用单根管道阀门关断问题的仿真计算对本文的模型进行了验证,计算结果与考虑频率相关摩擦损失的特征线方法的计算结果十分吻合。     

飞机结构下陷疲劳分析

以JL8飞机为例,运用新的理论,分析了飞机结构下陷的疲劳寿命,以及影响下陷寿命的关键因素,从而找到了一条提高飞机结构下陷寿命的途径。     

夹层玻璃力学模型的探讨

根据夹层玻璃的实验应力分析结果和板壳弹性理论,提出复合刚度矩阵处理均质连续夹层玻璃和分解外力计算单片玻璃两种力学模型和计算方法,分别针对夹层材料的不同弹性常数下的受力状态,采用有限元数值计算得出有一定精度并非常实用的夹层玻璃应力分布。     

单晶高温合金接近使用条件下的寿命估算与损伤分析

针对发动机热端部件承受的典型载荷谱，发展了一种通用的寿命预测方程和损伤分析方法。这个方法是在疲劳蠕变交互作用断裂特征图及其最大应力修正的寿命方程基础上建立的。根据ＤＤ３单晶合金的疲劳蠕变交互作用断裂特征图及其最大应力修正的寿命方程，验证了本方法是切实可行的。预测精度是符合要求的。