一种多步的基于切换星间测量的多星自主导航算法

针对基于星间测量的多星自主导航问题,从载荷优化和节约成本考虑,提出了一种单套敏感器切换测量的导航方案。建立了该导航方案下的系统状态空间模型,并基于扩展卡尔曼滤波方程给出了导航估计算法。基于多步卡尔曼滤波方法,将集中的滤波算法解耦为多个平行的子滤波器,使计算量降低到原算法的50%以下,并且在切换测量的导航方案下,部分解耦出的子滤波器可以只预测不更新,能够进一步地降低计算负担。给出了多步滤波算法的推导过程,证明了其与标准卡尔曼滤波的数学等价性,故算法的估计性能及计算结果与标准卡尔曼滤波一致,但计算速度有明显提升。最后,通过具体算例给出了算法的仿真验证。     

一种无引北三轴转台标定捷联惯组方法

使用三轴转台标定捷联惯组时,需要对三轴转台引北,用于精准测量捷联惯组相对地球北向的角度。为了减少引北带来的繁重工作量,在研究传统六位置标定方法的基础上,设计了十二位置标定方法。给出了十二位置翻转编排,建立了捷联惯组器件误差参数模型,详细推导了求解误差参数的方程式,并在高精度三轴转台上进行了试验验证。结果表明,在对三轴转台无引北的情况下,十二位置标定方法仍能标定出捷联惯组的24个器件误差参数,且精度与六位置标定方法相当,达到了预期目的。     

中国空间站燃烧科学实验系统PIV单元地面试验

中国空间站燃烧科学实验系统是用于开展微重力燃烧实验研究的综合性科学实验平台,可以实现燃烧流场测量。为了验证燃烧科学实验系统粒子图像测速(PIV)单元对燃烧流场测量的功能与可行性,本文基于与在轨状态一致的连续激光器和相机的空间布局,搭建了地面层流圆孔射流试验平台,选取Al₂O_3,TiO_2,ZrO₂三种示踪粒子进行冷态试验与热态试验。试验结果表明,自主研制Nd∶YVO₄泵浦连续激光器偏光角度合适,能照亮被测流场主流区域,燃烧科学实验系统PIV单元可用于低速燃烧流场测量;相同工况下,Al₂O₃粒子在冷态试验测量的速度值更接近于理论值,速度幅值比更接近1,更适用于低速流体测量。     

用于卫星入轨段测控的箭载天基测控中继系统

为满足卫星入轨段关键遥测参数下传和遥控指令上传的需求,设计了一种用于卫星入轨段测控的中继系统,方案主要基于火箭现成天基测控终端和卫星现成测控设备。介绍了中继系统的组成、工作原理和工作流程,研究了天基测控相控阵天线波束指向算法,设计了一种卫星遥测、遥控信号中继功能的地面测试系统。该箭载中继系统在快舟一号甲火箭上完成了两次飞行试验验证,两次飞行试验中继转发的卫星遥测数据完整,箭载卫星通信终端接收用户卫星遥测数据的载噪比大于20dB;地面测控中心接收天基遥测返向信号比特信噪比相对接收门限有3dB以上的余量。试验表明,该箭载天基测控中继系统通信链路余量充足,工作可靠,相比通过地面测控资源保障或卫星自身使用天基测控可节省一半以上成本。     

碘工质射频离子推力器栅极系统束流特性仿真

为分析碘工质射频离子推力器束流特性,应用粒子云网格算法（PIC）,对碘工质射频离子推力器栅极系统进行三维数值仿真。碘工质电离产物中除了大量存在的I⁺,还包含少量I₂⁺、I²⁺、I³⁺几种多价离子。对添加多价离子前后束流特性的仿真结果进行对比,得出该栅极系统离子空间分布、电势分布、离子相空间分布以及束流、束流发散角,并对变密度工况下束流大小进行统计。计算结果表明,程序能较好地模拟离子在栅极系统中的运动情况：添加多价离子后,等离子体悬浮电势有所上升,鞍点电势有所下降,但整体电势分布的变化幅度较小;添加多价离子后束流大小略有增加,束流发散角略有减小,通过理论分析可知仿真所得理论推力及理论比冲均有小幅度增加;放电室等离子体数密度增加到约2.4×10¹⁷m^-3时,该栅极系统达到了束流引出的极限,后续增大等离子体密度引出束流不增反降。模拟结果可以为碘工质射频离子推力器栅极系统的设计提供参考。     

RTK model and positioning performance analysis using Galileo four-frequency observations

This paper proposes a real-time kinematic (RTK) model that uses one common reference satellite for the Galileo system with four frequency observations. In the proposed model, the double-differenced (DD) pseudorange and carrier phase biases among the different frequencies are estimated as unknown parameters to recover the integer features of the DD ambiguities among the different frequencies for ambiguity resolution and precise positioning. Analysis results show that the E5a, E5b, and E5 frequencies have virtually the same performance in terms of the positioning accuracy, observation residuals, and ratio values of ambiguity resolution. However, the E1 frequency performs worse than the E5a, E5b, and E5 frequencies. The RTK results for the combination of multiple frequencies are much better than those for a single-frequency observation, the coordinates’ standard deviation is improved about 20–30%, and the ambiguity fix time is improved about 10%.     

Evaluation and improvement of coastal GNSS reflectometry sea level variations from existing GNSS stations in Taiwan

Global sea level rise due to an increasingly warmer climate has begun to induce hazards, adversely affecting the lives and properties of people residing in low-lying coastal regions and islands. Therefore, it is important to monitor and understand variations in coastal sea level covering offshore regions. Signal-to-noise ratio (SNR) data of Global Navigation Satellite System (GNSS) have been successfully used to robustly derive sea level heights (SLHs). In Taiwan, there are a number of continuously operating GNSS stations, not originally installed for sea level monitoring. They were established in harbors or near coastal regions for monitoring land motion. This study utilizes existing SNR data from three GNSS stations (Kaohsiung, Suao, and TaiCOAST) in Taiwan to compute SLHs with two methods, namely, Lomb–Scargle Periodogram (LSP)-only, and LSP aided with tidal harmonic analysis developed in this study. The results of both methods are compared with co-located or nearby tide gauge records. Due to the poor quality of SNR data, the worst accuracy of SLHs derived from traditional LSP-only method exceeds 1?m at the TaiCOAST station. With our procedure, the standard deviations (STDs) of difference between GNSS-derived SLHs and tide gauge records in Kaohsiung and Suao stations decreased to 10?cm and the results show excellent agreement with tide gauge derived relative sea level records, with STD of differences of 7?cm and correlation coefficient of 0.96. In addition, the absolute GNSS-R sea level trend in Kaohsiung during 2006–2011 agrees well with that derived from satellite altimetry. We conclude that the coastal GNSS stations in Taiwan have the potential of monitoring absolute coastal sea level change accurately when our proposed methodology is used.     

工程数据库管理系统的探讨

工程数据库管理系统是一个面向CAD/CAM的数据(包括知识)管理系统,它是CAD/CAM软件系统的核心。本文对工程数据库系统在CAD/CAM系统中的地位和作用、工程数据库管理系统的特殊要求以及多级数据管理、多重数据模型、复杂实体的定义和操作、变长域类型及版本化作了一些探讨和建议。     

对地观测DSS任务分配问题的CSP模型与算法

任务分配是对地观测分布式卫星系统(Distributed Satellites System, DSS)自主协作运行过程中的一个重要环节. 针对任务分配中的约束满足问题(Constraint Satisfaction Problem, CSP), 以DSS完成任务总耗能最少为原则, 构建了任务分配问题的CSP模型, 并引入MAS理论中的合同网协议, 给出模型的求解算法, 通过仿真算例对模型和算法进行了验证.     

新型电子束焊机阴极加热电源自动调节系统

开发了一种新型电子束焊机阴极加热电源自动调节系统,包括新型主电路拓扑和对应控制策略,该系统能够使阴极处在最佳加热电流状态,从而提高电子束流稳定性.并且在检测到电子枪未加高压时,阴极加热电流自动关闭,在加有高压但束流给定为零时,阴极加热电流自动减少,能大幅增加阴极的使用寿命.经试验证明该系统相比传统阴极加热电源操作简洁、快速和准确,对焊缝成形质量好.