结冰对民用飞机飞行性能的影响分析

在获取民用飞机适航合格审定证明前,必须通过飞行试验,并在试验中演示验证民用飞机能在CCAR25部附录C确定的连续和间断的最大结冰状态下安全运行。基于此背景,计算并得到某型机两种构型在45min待机冰型下的飞行性能,与无冰状态下对应构型的飞行性能进行对比分析。结果表明,结冰对飞机的飞行性能具有较大的影响。     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

水热-凝胶法ZrO2 气凝胶的制备与表征

以硝酸氧锆为锆源,尿素为凝胶促进剂,通过水热凝胶法结合超临界乙醇干燥,可成功制备出具
有良好纳米三维网络结构的ZrO2 气凝胶。采用透射电镜(TEM)、比表面积及孔隙度分析仪(BET),X 射线衍
射仪等测试手段对其结构进行了表征与测试。结果表明,ZrO2 气凝胶主要由无定型和四方晶相组成,其比表
面积为445 m2 / g,孔径主要分布在5 ~7 nm 和30 ~40 nm 两处。     

基于累积磨损量分布的飞机刹车片可靠性分析

针对高可靠、长寿命型产品可靠性分析难于获得寿命数据的问题,基于累积磨损量分布研究刹车片的可靠性评估方法。在飞机刹车片退化机理分析的基础上,选择正态分布、对数正态分布、威布尔分布描述其累积磨损量,通过建立累积磨损量分布参数的时序模型,确定未来时刻累积磨损量的分布,对刹车片进行寿命预测。     

涡扇发动机轴对称引射收敛喷管红外辐射特性

数值研究了涡扇发动机轴对称引射收敛喷管的红外辐射特性.排气系统的流场计算采用商用数值模拟软件,红外辐射特性计算采用自主开发的软件NUAA-IR,计算分析了轴对称收敛喷管和引射收敛喷管在3~5μm波段红外辐射特性以及喷管内不同固体壁面在探测方向上的红外辐射贡献.结果表明:引射收敛喷管的红外抑制作用主要在于引射加强了尾喷流与环境大气的掺混,减小了尾喷流的长度,降低了燃气流的红外辐射;引射收敛喷管对喷管内固体壁面的遮挡以及降温作用很小,只在方位角为20°方向上对内涵壁面、外涵内壁等中低温壁面有效;引射收敛喷管的总积分辐射强度在方位角为0°~15°范围内与收敛喷管几乎相等,在其他方位角范围内均小于收敛喷管,且在方位角为40°方向上降低幅度达到最大,约为34%.      

Attitude control system design and on-orbit performance analysis of nano-satellite––‘‘Tian Tuo 1’’

‘‘Tian Tuo 1'(TT-1) nano-satellite is the first single-board nano-satellite that was successfully launched in China. The main objective of TT-1 is technology demonstration and scientific measurements. The satellite carries out the significant exploration of single-board architecture feasibility validation, and it is tailored to the low-cost philosophy by adopting numerous commercialoff-the-shelf(COTS) components. The satellite is featured with three-axis stabilization control capability. A pitch bias momentum wheel and three magnetic coils are adopted as control actuators.The sun sensors, magnetometers and a three-axis gyro are employed as the measurement sensors.The quaternion estimator(QUEST) and unscented Kalman filter(UKF) method are adopted for the nano-satellite attitude determination. On-orbit data received by ground station is conducted to analysis the performance of attitude determination and control system(ADCS). The results show that the design of ADCS for TT-1 is suitable, robust and feasible.     

基于技术参数评估的涡扇发动机总体性能设计分析

为了充分掌握各代涡扇发动机技术参数水平及其发展趋势,统计包括现役型号在内的15台2～4代涡扇发动机的总体性能参数、循环参数和部件参数,采用考虑涡轮冷却的总体性能计算和重量预测相结合的发动机技术参数综合评估模型并利用计算程序绘制趋势曲线,评估技术参数的发展趋势,结果表明技术参数逐年改善的趋势是比较稳定的,并用曲线趋势外推法取得下一代关键参数的定量数据。在此基础上探索下一代高推重比涡扇发动机可能的总体性能方案,为下一代先进涡扇发动机的预研和设计提供参考。     

多尾鳍仿生航行器推进性能的三维数值研究

采用格子波尔兹曼方法及浸没边界法,发展了一套适用于自由游动的三维数值研究程序。进而以多尾鳍推进仿生航行器为原型,讨论了尾鳍数目、形状、材料刚度等构型参数及振幅、频率等尾鳍摆动参数对推进性能的影响。结果表明对称布置、反对称摆动的双尾鳍能够明显消除侧向力而避免航行器主体的横向晃动,且推力大于两个单独尾鳍的简单加和;在中等Reynolds数下,具有波动性质的柔性尾鳍不论是推进速度还是推进效率均优于刚性尾鳍;当尾鳍单纯摆动推进时,具有完整鳍面的半椭圆形尾鳍的推进性能优于后部有缺口的深叉形尾鳍。     

军用直升机雷达隐身性能仿真与评估

采用高频方法计算了某型通用直升机及其隐身改型的RCS数据,基于现有雷达隐身性能计算方法和直升机低空飞行特点,对直升机在单部雷达和雷达组网两种情况下的雷达隐身性能进行仿真分析,给出了单部雷达和雷达组网发现目标的判定准则,分析了直升机可探测范围曲线、平均综合检测概率和暴露时间等隐身指标。通过仿真分析,评估了不同飞行高度下RCS减缩与直升机隐身性能的定量关系,为直升机的隐身设计提供了参考依据。     

民用运输机审定着陆距离计算方法浅析

着陆阶段是飞行中最关键的阶段,也是事故多发阶段,着陆距离的计算是民用运输机着陆性能分析的重要方面。本文讨论了在满足法规的条件下计算审定着陆距离的方法,并以某机型为例,给出了用这种方法计算不同条件下审定着陆距离的结果,结果表明这种审定着陆距离的计算方法是切实可行的。