改善反作用轮低速性能的补偿观测器方法

基于Ｄａｈｌ摩擦模型,给出了用于卫星姿态三轴稳定控制的反作用轮低速动力学方程,就反作用轮转速过零对卫星姿态产生的扰动现象进行了分析,提出了一种利用非线性观测器估计摩擦力矩,并予以补偿的补偿观测器方法。仿真结果表明,该方法改善了反作用轮低速性能,提高了卫星姿态控制的指向精度和稳定度。     

空间机器人神经网络自适应滑模目标操控轨迹跟踪控制

针对参数未知的空间目标操控问题,考虑空间机器人负载不确定性、系统动力学不确定性和环境扰动等因素,为实现操作过程的稳定控制及机器人轨迹的有效跟踪,提出一种基于径向基神经网络估计不确定项的自适应增益非奇异终端滑模变结构控制器。首先基于拉格朗日法建立空间机器人的刚体动力学模型。考虑空间机器人基座姿态主动控制模式,使用径向基神经网络对模型中的不确定项进行估计。进而提出基于神经网络估计的非奇异终端滑模控制器,并针对不确定性和扰动的估计误差设计自适应增益,以期实现空间机器人系统轨迹跟踪控制的收敛。仿真校验结果表明所设计的控制方法具有较好的误差收敛速度和控制精度。     

非牛顿大滑滚比工况的斜齿轮热摩擦特性分析

考虑啮合过程中接触线长度及齿面载荷的时变性,结合沿接触线方向综合曲率半径及卷吸速度的瞬态特点,建立满足航空传动润滑剂非牛顿流体及大滑滚比工况的有限长线接触斜齿轮热弹流润滑(TEHL)模型。采用多重网格法及逐列扫描法,获得适用于宽泛工况范围的斜齿轮热弹流润滑完全数值解;分析非牛顿及大滑滚比情形下的斜齿轮传动热摩擦特性。结果表明:斜齿轮端部存在明显压力及温度尖峰,且离入口愈近膜厚会略减小;非牛顿特性对温度场影响显著,且接触线过节点时温度分布呈“V”型分布;摩擦因数沿啮合线方向在节点处接近于0且向两侧逐渐增大,同时随滑滚比的增大而增大。      

Impact of bending dies with different friction forms on forming force and quality of tubes manufactured by free bending technology

In the 3D free bending forming system, the bending die can be designed either in a sliding type or rolling friction type. Bending die-based sliding friction type is often called normal bending dies; however, the bending dies-based rolling friction type includes bending die-based roller type and ball type in structure. In the current study, the impact of three bending dies on the forming force, and the bent tube quality was investigated. The obtained results showed that the tangential stresses and strains of the tubes formed by the bending die-based roller type were the smallest among the three bending dies. Besides, the spherical bearing force P_U was reduced drastically after using the roller type and ball type compared to the sliding friction type. Moreover, the uniformity of the wall thickness distribution of the tubes formed by the roller type and ball type was better than those obtained from the sliding friction type. In addition, the cross-section distortion rate was reduced by 2.8% using the roller type, and 1.8% using ball-type compared to the sliding friction type.     

高马赫数层流摩阻数值计算精度

飞行器在高空高速飞行时黏性效应显著,摩阻预示精度对飞行器的关键气动性能意义重大。目前,摩阻预示主要依赖数值计算,但高马赫数层流摩擦阻力计算与试验测量结果仍存在差距。以具有高速飞行器典型部件特征的球锥、三角翼为对象,结合风洞试验摩阻测量结果,使用国家数值风洞（NNW）数值计算软件和自研CFD程序研究了数值计算中影响摩阻计算精度的格式数值耗散及壁面温度边界条件等重要因素。研究结果表明：数值耗散越小,表面摩阻的计算精度越高;在速度较低的边界层近壁区内关闭熵修正,将有助于提高表面摩阻的预示精度。此外,在高马赫数流动问题的数值模拟中,壁面温度条件对表面摩阻计算同样具有重要影响。最后,基于分析结果和工程需要提出了对高精度摩阻数值预示的研究需求。     

中心进气转静系转盘风阻扭矩数值模拟

采用计算流体力学(CFD)商业软件CFX从流动参数及几何结构两个方面对中心进气转静系盘腔内转盘风阻扭矩特性进行了数值模拟研究,同时搭建一个转盘风阻扭矩实验台测量自由盘风阻扭矩.中心进气转静系转盘风阻扭矩与经典经验公式进行了对比,结果表明:利用数值模拟方法,得到的无量纲扭矩系数与经典经验关系式计算得到的数据总体相差小于10%,利用湍流参数来表征转盘转速以及叠加流流量,对于分析转盘风阻扭矩非常便利.利用湍流参数定量分析时需注意叠加流以及转速的量级同样影响着风阻扭矩的数值.几何结构对于风阻扭矩也有影响,但相比流动参数影响较小.      

节点外啮合齿轮胶合承载能力中平均摩擦因数的计算方法

分析了现有胶合承载能力计算中平均摩擦因数计算方法的不足之处,根据节点外啮合齿轮传动的啮合特点,以相关标准中渐开线圆柱齿轮的计算公式为基础,提出了一种更为合理且精度较高的平均摩擦因数计算方法,以满足节点外啮合齿轮胶合承载能力计算的需要.通过对内、外啮合副节点前啮合和节点后啮合实例的计算,得出除外啮合节点前啮合以外,利用标准计算得到的平均摩擦因数的误差都超过18.5%,而改进计算方法所得的误差都在6.5%之内,证实了这种改进的平均摩擦因数计算方法具有更高的精度,而且这一计算方法也适用于标准齿轮传动.      

改进的GPS掩星滑动频谱方法

在大气多路径和噪声的条件下,高斯白噪声会造成滑动频谱方法获得的弯曲角与真值之间的偏离,无法获得较好的反演结果。为此,文章提出了一种改进的滑动频谱方法,即利用信号的振幅和谱能量信息对滑动频谱方法进行修正,削弱了信号中噪声的影响,与真值较为接近。分别用改进前后两种方法对中华卫星三号计划（Constellation Observing System for Meteorology, Ionosphere and Climate,COSMIC）的掩星进行反演,并将其折射率计算结果和通过全谱反演方法获得的折射率一起,与欧洲中期天气预报中心（European Centre for Medium Range Weather Forecasts,ECMWF）的分析场资料进行了统计比较。结果表明：改进的滑动频谱方法删除了信号中的部分噪声,减少了系统偏差;与全谱反演方法进行比较,发现两者具有相当的反演精度。     

一种用于空间群目标分辨的滑动窗轨迹跟踪算法

针对大多数现有的微多普勒分析理论难以解决空间群目标的监测与识别问题,本文提出一种基于提取目标运动特征的弹道中段群目标分辨方法。首先建立了多个具有滑动散射中心的旋转对称目标模型并得到其m-D曲线,在此基础上,利用形态学图像处理方法抑制一维距离像旁瓣,然后提出了一种滑动窗轨迹跟踪的方法分离出各散射点相互交叉的m-D曲线,再对分离结果进行经验模式分解(Empirical-Mode Decomposition, EMD),最后通过提取能够反映目标运动特征的固有模态函数(Intrinsic Mode Function ,IMF),实现了群目标分辨。仿真实验校验了所提方法的可行性和鲁棒性。     

Adaptive fuzzy terminal sliding mode control for the free-floating space manipulator with free-swinging joint failure

Space manipulator with free-swinging joint failure simultaneously contains kinematic and dynamic coupling relationships, so it belongs to a new underactuated system. To allow the manipulator to carry on tasks, an effective robust underactuated control method for the space manipulator with free-swinging joint failure is studied in this paper. Considering the effect of model uncertainty and joint torque disturbance, a robust underactuated control system based on the Terminal Sliding Mode Controller (TSMC) is designed, but two drawbacks are discussed: (A) Robustness depraves with eliminating chattering. (B) Control parameters are difficult to be determined under unknown uncertainty and disturbance. To improve the TSMC, the adaptive fuzzy controller is introduced to estimate the real effect of unknown uncertainty and disturbance according to deviations of sliding mode and its reaching law. The estimated result is directly compensated into active joints torque. In simulation, the space manipulator with free-swinging joint executes tasks based on the TSMC and the Adaptive Fuzzy Terminal Sliding Mode Controller (AFTSMC) respectively. Same tasks can be finished with smaller joints torque and stronger robustness based on the AFTSMC. Therefore, AFTSMC can serve as an effective robust control method for the space manipulator with free-swinging joint failure under unknown model uncertainty and torque disturbance.