桥式试件微动疲劳寿命预测与试验研究

对钛合金桥式试件进行数值分析与微动疲劳试验研究,提出了用MSWT参数预测裂纹萌生位置的方法和基于MSWT参数的微动疲劳寿命预测模型。试验结果与断口分析表明:疲劳裂纹出现在微动试件的接触区边缘,与MSWT参数预测的裂纹萌生位置一致。利用桥式试件的微动疲劳试验数据,获得了寿命预测模型中的相关参数,并采用相关文献中燕尾榫连接结构的试验结果对该预测模型进行了验证。     

Calibration errors in determining slant Total Electron Content (TEC) from multi-GNSS data

The global navigation satellite system (GNSS) is presently a powerful tool for sensing the Earth's ionosphere. For this purpose, the ionospheric measurements (IMs), which are by definition slant total electron content biased by satellite and receiver differential code biases (DCBs), need to be first extracted from GNSS data and then used as inputs for further ionospheric representations such as tomography. By using the customary phase-to-code leveling procedure, this research comparatively evaluates the calibration errors on experimental IMs obtained from three GNSS, namely the US Global Positioning System (GPS), the Chinese BeiDou Navigation Satellite System (BDS), and the European Galileo. On the basis of ten days of dual-frequency, triple-GNSS observations collected from eight co-located ground receivers that independently form short-baselines and zero-baselines, the IMs are determined for each receiver for all tracked satellites and then for each satellite differenced for each baseline to evaluate their calibration errors. As first derived from the short-baseline analysis, the effects of calibration errors on IMs range, in total electron content units, from 1.58 to 2.16, 0.70 to 1.87, and 1.13 to 1.56 for GPS, Galileo, and BDS, respectively. Additionally, for short-baseline experiment, it is shown that the code multipath effect accounts for their main budget. Sidereal periodicity is found in single-differenced (SD) IMs for GPS and BDS geostationary satellites, and the correlation of SD IMs over two consecutive days achieves the maximum value when the time tag is around 4?min. Moreover, as byproducts of zero-baseline analysis, daily between-receiver DCBs for GPS are subject to more significant intra-day variations than those for BDS and Galileo.     

TC4-DT焊接接头Ⅰ-Ⅱ复合型疲劳裂纹扩展实验及模拟研究

拉剪复合载荷作用下,构件中的裂纹呈现复杂的Ⅰ-Ⅱ复合型扩展模式,研究其扩展规律对准确评估构件疲劳寿命具有重要意义。针对TC4-DT钛合金电子束焊接头Ⅰ-Ⅱ复合型疲劳裂纹扩展规律开展研究,设计并加工紧凑拉伸剪切(CTS)试样,通过开展不同加载角度下接头试样的疲劳裂纹扩展实验,得到接头Ⅰ-Ⅱ复合型裂纹的a-N曲线及疲劳裂纹扩展路径。在上述基础上引入Ⅰ-Ⅱ复合型等效应力强度因子并结合Paris公式建立TC4-DT电子束焊接头Ⅰ-Ⅱ复合型疲劳裂纹扩展速率方程。采用扩展有限元法(XFEM)对复合型疲劳裂纹扩展过程进行数值模拟研究,得到不同加载角度下的扩展规律,并与实验结果进行比较。结果表明:不同加载角度下Ⅰ-Ⅱ复合型疲劳裂纹开裂角模拟值与实验结果误差均在10%以内,并且扩展路径均与实验结果吻合;XFEM能够有效预测复合型疲劳裂纹扩展路径。     

某型发动机进气机匣联动环跑道裂纹修复技术研究

对某型发动机进气机匣联动环跑道裂纹故障进行机理分析,认为联动环跑道处的机加接痕明显,发动机工作过程中风扇一级转子叶片激起机匣振动,机匣本身强度不足,导致在故障部位萌生裂纹并扩展。采用激光熔覆+氩弧焊复合方式利用导热法原理进行修复,自制铜夹具进行导热,可以减少机件的形变量;通过改变坡口形式、减少金属熔覆填充量,改变激光熔覆的工艺参数,控制热输入量、单位能量密度,可以使形变量进一步减少,满足了产品尺寸和形位要求。     

Rapid ionospheric variations at high latitudes: Focusing on Greenland

The Helheim glacier, located in southeast Greenland, has more than ten campaign-type Global Positioning System (GPS) sites; data processing led to the observation of a very rapid change in the ionospheric delay. To identify the cause of these sporadic disturbances, we analyzed the slant total electron content (STEC), single-differenced STEC (SD-STEC) and scintillation proxy index called the delta phase rate (DPR). From this analysis, the abrupt change of those ionospheric indicators was attributed to the line-of-sight direction to the satellite and the temporal sequence of the event was found to be highly correlated with the geometry of the GPS sites. In addition, the disturbance based on the result of SD-STEC occurred mostly during the night, from 17 UTC through 7 UTC, and across a band spanning the east-west direction. Based on the DPR indices obtained from GPS stations distributed across all of Greenland, Iceland, and northeastern Canada, the rapid ionospheric variation was found to be correlated with the time of the day and the geomagnetic latitude of the station. The disturbance was larger at the relatively low geomagnetic latitudes at night but was more significant at higher latitudes in the daytime. These rapid ionospheric variations tended to appear in band shapes parallel to the geomagnetic field. These results allow us to attribute such disturbance observed at the Helheim glacier to aurora-related phenomena.     

固体推进剂复合型裂纹扩展数值计算

用粘弹性有限元法,分别以尖角形、椭圆形、圆形裂尖反映裂尖的变形,以最大周向应力准则和最大能量释放率准则作为裂纹扩展方向的判断依据,以J积分作为裂纹扩展的起始判据,计算了不同倾斜角裂纹的初始扩展方向.采用多个扩展步递增循环计算的方法,得到了不同倾斜角裂纹的扩展路径,并在扩展路径上设置粘结损伤单元,模拟了裂纹的动态扩展过程...     

A new method to predict fatigue crack growth rate of materials based on average cyclic plasticity strain damage accumulation

By introducing a fatigue blunting factor, the cyclic elasto-plastic Hutchinson-Rice-Rosengren (HRR) field near the crack tip under the cyclic loading is modified. And, an average damage per loading-cycle in the cyclic plastic deformation region is defined due to Manson-Coffin law. Then, according to the linear damage accumulation theory-Miner law, a new model for predicting the fatigue crack growth (FCG) of the opening mode crack based on the low cycle fatigue (LCF) damage is set up. The step length of crack propagation is assumed to be the size of cyclic plastic zone. It is clear that every parameter of the new model has clearly physical meaning which does not need any human debugging. Based on the LCF test data, the FCG predictions given by the new model are consistent with the FCG test results of Cr2Ni2MoV and X12CrMoWVNbN 10-1-1. What’s more, referring to the relative researches, the good predictability of the new model is also proved on six kinds of materials.     

基于材料微观特性的涡轮盘疲劳裂纹萌生寿命数值仿真

 为了研究材料微观特性对结构疲劳寿命的影响,根据Tanaka-Mura疲劳裂纹萌生寿命计算理论,模拟某镍基粉末合金涡轮盘喉道表面疲劳裂纹萌生寿命。利用泰森多边形生成法,模拟微观多晶结构,建立宏-细观模型相结合的三维仿真模型。实现3项关键技术:1)在三维模型中模拟了面心立方晶体中{111}面族的12条主滑移系;2)应用缺口根部裂纹萌生的Tanaka-Mura理论模型模拟一条微裂纹在另一条裂纹尖端萌生;3)模拟了微裂纹的起裂、扩展与联合过程,最终形成一条宏观裂纹。对某表面带刀痕涡轮盘疲劳裂纹萌生寿命数值仿真结果与真盘试验结果相差20%。研究表明,减小晶粒尺寸、降低表面粗糙度、形成表面压缩残余应变以及析出沉淀颗粒都有利于提高涡轮盘的疲劳裂纹萌生寿命。     

恒幅及飞行模拟载荷下厚度对裂纹增长的影响

不同厚度试样的疲劳裂纹扩展试验及断口微观分析表明,恒幅加载低应力比飞行模拟载荷条件下具有明显的厚度影响。考查了模型对厚度影响的预测能力。Newman的模型具有预测厚度影响的潜力,广义改进的wellenborg模型不含有厚度影响的考虑,即使通过调整约束系数α的方法也不能计及厚度的影响。厚度对裂纹增长影响的物理原因及模型化有待于进一步研究。     

Comparative study between crack closure model and Willenborg model for fatigue prediction under overload effects

A comparative study is performed between a crack closure model and the Willenborg model, which can calculate the fatigue crack growth rate under the overload effects. The modified virtual crack annealing (VCA) model is briefly reviewed, which is based on the equivalent plastic zone concept. In this method, the retardation phenomenon is explained by the crack closure level variation, which is derived from the interactions between forward and reverse plastic zones ahead of the crack tip. As a comparison, the Forman equation in conjunction with the Willenborg model is also reviewed. The retardation phenomenon is described by directly modifying the stress intensity factor. It is known that the large plastic zone created by the overload can decelerate the fatigue crack growth rate until the crack grows beyond this region. A relationship between the plastic zone and the modified stress intensity factor is developed, which is a mathematical fitting equation instead of physical-based formulation. The experimental data in aluminum alloys are used to val-idate these two models. Overall, good agreement is observed between the model predictions and the testing data. It is noted that the approach based on modified VCA model can give more accurate prediction curves than the Willenborg model.