解耦N-S/DSMC方法计算推力器真空羽流的边界条件研究

准确模拟羽流流场是合理评估空间推力器真空羽流效应的基础。因羽流流场同时包含连续和稀薄两种流动机理,通常采用解耦方式的Navier-Stokes(N-S)方程和直接模拟蒙特卡罗(DSMC)混合方法对其进行模拟。为保证解耦N-S/DSMC方法应用于羽流计算时的准确性并尽量提高其计算效率,对计算中的DSMC入口和喷管壁面等边界条件设置问题开展了研究。通过与文献中低总压工况的羽流试验数据比较,确定了合理设置DSMC入口边界位置、壁面反射类型、壁温等边界条件的方法。针对将此方法应用于实际推力器工况计算时效率过低的问题,通过多种数值试验,表明从喷管出口处开始沿KnGL为0.05的等值线作为DSMC入口界面可同时保证仿真精度和较高的计算效率;并证明实际工况下壁温设置对羽流场仿真结果影响不大。     

Dynamic analysis of C/C composite finger seal

A seal device as an important component of aeroengines has decisive influence on per- formance, reliability, and working life of aeroengines. With the development of aeroengines, demands on the performance characteristics of seal devices are made strictly. Finger seal as a novel kind of sealing device, recently attracts more and more attentions in academic circles and engineer- ing fields at home and abroad. Research on finger seals has been extensively developed, especially on leakage and wear performances under dynamic conditions. However, it is a pity that the work on finger seals has been limited with a single approach that is improving the performance by structural optimization; in addition, the technology of dynamic analysis on finger seals is weak. Aiming at the problems mentioned above, a distributed mass equivalent dynamic model of finger seals considering the coupling effect of overlaid laminates is established in the present paper, the dynamic perfor- mance of 2.5 dimension C/C composite finger seal is analyzed with the model, and then the effects of fiber bundle density and fiber bundle preparation direction on finger seal＇s dynamic performance are discussed, as well as compared with those of Co-based alloy finger seal. The current work is about dynamic analysis of finger seals and application of C/C composite in this paper may have much academic significance and many engineering values for improving research level of finger seal dynamics and exploring feasibility of C/C composite being used for finger seals.     

多重纳米结构轻质高强铝基复合材料的制备和组织性能

为了研究多重纳米结构对块体材料强化和变形能力的影响机制,采用粉末冶金法制备了多重纳米结构的B4C颗粒增强铝基复合材料,并对复合材料的强化和形变破坏机制进行了定量和定性的讨论。由100%球磨复合粉末制备的块体复合材料的室温压缩强度为670MPa;当加入10vol%气雾化态的Al2024粉末后,复合材料的室温压缩强度升高到1.115GPa;之后随着气雾化态Al2024粉末含量的增加,复合材料的强度逐渐下降,但是没有产生明显的塑性变形;当气雾化态Al2024粉末的含量增加到50vol%时,复合材料的压缩强度下降到580MPa,断裂前变形率达到了10%。扫描电镜(SEM)和透射电镜(TEM)的分析结果显示,亚微米级的B4C颗粒、位错以及纳米晶基体分别通过Orowan强化、位错强化和细晶强化机制对复合材料进行强化;粗晶Al2024区域与复合结构区域的比例显著影响复合材料的形变及破坏机制。     

连续尺度变换方程在稳态及非稳态流动模拟中的应用

为了提高涡粘性假设的湍流模型对于非稳态流动的求解精度,同时兼顾其对于稳态流动的求解性能,将雷诺应力项与连续变换方程(CSSE)结合而形成新的应力项,使其根据流场尺度、网格尺度及Kolmogorov尺度来自动调节当地的应力雷诺应力模化水平,避免网格因素在流场模拟中产生不利影响,改正了混合RANS/LES方法的速度型偏离对数率问题;同时,该方法并未引入显式亚格子模型(SGS),因此回避了亚格子系数确定对于流场模拟精度产生的影响,改善了湍流模型对于流动不稳定性的辨识精度。在湍流平板算例中,CSSE方法计算的边界层速度型精度与雷诺平均方法(RANS)相当,而对于圆柱尾迹的模拟则证明了CSSE方法具有混合RANS/LES方法的优点,即能够准确模拟流动的不稳定性特征。     

面内弯曲载荷作用下两边简支两边固支复合材料层合板的屈曲

为扩充航空复合材料结构稳定性设计手段,基于Levy形式级数和有限差分法,提出了面内纯弯曲载荷作用下两边简支两边固支（SSCC）复合材料层合板临界屈曲载荷的数值解法。首先,应用有限差分法将挠度函数进行离散化处理;然后利用边界条件扩充方程组,最后将临界屈曲载荷的求解转化为广义特征值问题。通过数值算例分别在各向同性板和复合材料层合板上验证了本文方法,并与有限元方法（FEM）进行了比较。结果表明,本文方法具有很高的精度,为复合材料层合板的屈曲分析开辟了新的途径。     

压辊材料及形状对纤维铺放压紧效果的影响

近年来纤维铺放（AFP）技术被广泛用于大型复杂飞机复合材料构件成型。为了保证纤维铺放过程的一致性,纤维铺放压辊必须在适应芯模型面的同时具有较好的压紧力分布均匀性。鉴于此,对不同弹性模量的压辊材料进行了试验分析,薄膜压力传感器及超声显微镜测试结果表明,低弹性模量的压辊材料变形较大,较好地适应了芯模表面,压力分布相对均匀且可以减少铺层的层间孔隙数量,硅橡胶压辊比聚乙烯压辊压紧力分布均匀性提高了50%~60%,铺层孔隙率降低了92.1%。针对孔隙分布主要集中在压辊两端及压紧力在压辊两端下降幅度较大的问题,采用ANSYS Workbench对压辊端部进行斜端面优化,得到最优倾斜角度为20°;测试结果表明斜端面压辊压力分布均匀性比直断面压辊提高了42.9%,铺层孔隙率下降了51.6%。     

Determination of thermal expansion coefficients for unidirectional fiber-reinforced composites

In the present work, the coefficients of thermal expansion（CTEs） of unidirectional（UD）fiber-reinforced composites are studied. First, an attempt is made to propose a model to predict both longitudinal and transverse CTEs of UD composites by means of thermo-elastic mechanics analysis. The proposed model is supposed to be a concentric cylinder with a transversely isotropic fiber embedded in an isotropic matrix, and it is subjected to a uniform temperature change. Then a concise and explicit formula is offered for each CTE. Finally, some finite element（FE） models are created by a finite element program MSC. Patran according to different material systems and fiber volume fractions. In addition, the available experimental data and results of other analytical solutions of CTEs are presented. Comparisons are made among the results of the cylinder model,the finite element method（FEM）, experiments, and other solutions, which show that the predicted CTEs by the new model are in good agreement with the experimental data. In particular, transverse CTEs generally offer better agreements than those predicted by most of other solutions.     

苎麻纤维增强酚醛树脂基复合材料的湿热性能研究

通过模压工艺制备了苎麻纤维织物增强酚醛树脂基复合材料层合板,研究了模压层合板在不同湿热环境下的水吸收与扩散及力学性能。研究表明:在20℃,40℃和60℃三种温度下,相对湿度的上升使层合板瞬时吸湿速率增大很明显,而在50%相对湿度下,温度对层合板的饱和吸水率的影响不大。当吸湿份数在0.5以下时,层合板在50%的相对湿度和20℃,40℃和60℃三种温度下,水扩散系数分别为2.16×10-6cm2/s,2.94×10-6cm2/s和6.61×10-6cm2/s。层合板的力学性能随吸水率的增加而下降。通过扫描电子显微镜(SEM)观察,层合板力学性能下降的主要原因是水分破坏了纤维和树脂的界面,同时进入纤维的空隙中,影响了复合材料中的应力传递,使复合材料力学性能下降。     

基于比拟理论计算圆柱/翼型的气动噪声

采用计算流体力学(CFD)与"声比拟"相结合的方法,通过两个步骤模拟流动的声学远场。第一步,在包含所有声源的近场区域内,通过求解URANS方程获得控制面处的非定常流场参数;第二步,采用基于可穿透数据面的FW-H方法模拟声学远场。该方法与传统的半经验方法相比,计算精确,易于工程实现,并且可以计算非线性噪声。根据气动声学计算积分公式,构造了高阶的时间离散格式,采用高斯积分公式计算圆柱/翼型的气动噪声。在时域和频域上计算了观测点处的声压及声压级随时间步数的变化情况,其结果与国外实验结果对比取得了较好的一致性,此外研究了翼型尾流部分界面对计算精度的影响。     

MASCOT 2即将开始第二阶段地面测试

日前,CFM国际公司先进的三维编织树脂转移成型(3-DW RTM)风扇项目正在按计划进行测试,公司将开始MASCOT 2风扇验证机发动机的第二阶段地面测试。碳纤维、三维编织复合材料RTM(树脂转移成型)风扇是将于2016年投入使用的CFM先进的LEAP发动机的一项基本技术。