全文获取类型
收费全文 | 266篇 |
免费 | 53篇 |
国内免费 | 79篇 |
专业分类
航空 | 272篇 |
航天技术 | 36篇 |
综合类 | 44篇 |
航天 | 46篇 |
出版年
2024年 | 3篇 |
2023年 | 9篇 |
2022年 | 4篇 |
2021年 | 19篇 |
2020年 | 13篇 |
2019年 | 12篇 |
2018年 | 14篇 |
2017年 | 19篇 |
2016年 | 40篇 |
2015年 | 10篇 |
2014年 | 10篇 |
2013年 | 8篇 |
2012年 | 25篇 |
2011年 | 21篇 |
2010年 | 15篇 |
2009年 | 20篇 |
2008年 | 21篇 |
2007年 | 17篇 |
2006年 | 14篇 |
2005年 | 10篇 |
2004年 | 16篇 |
2003年 | 10篇 |
2002年 | 11篇 |
2001年 | 8篇 |
2000年 | 6篇 |
1999年 | 8篇 |
1998年 | 5篇 |
1997年 | 4篇 |
1996年 | 6篇 |
1995年 | 4篇 |
1994年 | 4篇 |
1993年 | 3篇 |
1992年 | 5篇 |
1990年 | 2篇 |
1989年 | 2篇 |
排序方式: 共有398条查询结果,搜索用时 15 毫秒
121.
新淬火状态硬铝合金板的成形性能及数值模拟 总被引:2,自引:0,他引:2
研究了铝合金退火状态和新淬火状态下的成形性能,给出了主要成形性能指标与自然时效及预变形的关系,表明在新淬火状态一定时间内,铝合金仍然具有良好的成形性能,淬火前的变形和淬火后的时效过程将降低成形性能;通过退火状态和新淬火状态材料成形的数值模拟对比,表明新淬火状态材料成形具有以下特点:新淬火状态材料成形需要更大的力能参数,残余应力和回弹较大,成形后变薄较小,厚度分布较均匀,随着时效时间增加和淬火前变形的增加,成形力、厚度变薄和回弹增大. 相似文献
122.
123.
124.
板材最优路径成形理论与方法 总被引:7,自引:0,他引:7
按最优路径成形板材将获得理想的成形效果,这种最优成形路径可通过多点成形技术来实现。本文基于理想路径(最小塑性功路径)成形理论,提出了板材最优路径成形的概念。最优成形路径可由初始构形、目标构形以及一系列中间构形描述出来,根据理想路径成形的变形及本构关系,文中建立了计算初始构形的有限元方法;建立了确定中间构形的泛函,给出了求解中间构形的数值方法。根据给出的方法设计了近似最优路径成形──多道次多点成形实验,实验结果表明,采用近似最优路径成形,球面目标形状的最大变形曲率提高了11%~40%;马鞍面目标形状的最大变形曲率提高了15%-50%。 相似文献
125.
本文通过几个典型试验,分析了1420铝锂合金的两种不同热处理状态下的冷成形性能,得出的试验数据和结论。对生产具有一定的指导意义。 相似文献
126.
采用塑性流动理论,薄壳无力矩理论及幂函数强化模型,对求解轴对称塑性平面应力问题的数值参数法作了进一步的研究,推导出成形力学分析的一阶微分方程组,在此基础上,将该微分方程相应用于薄壁圆管轴压外翻成形的稳态流动分析,计算时采用了四阶龙格库塔法,并获得了应力,应数值解,本文通过大量的计算,分析了边界条件对计算结果的影响,并将理论计算结果与实验作了比较。研究结果表明,轴对称塑性平面应力问题可以转换为一阶常 相似文献
127.
128.
129.
Forming Characteristics of Al-alloy Large-diameter Thin-walled Tubes in NC-bending Under Axial Compressive Loads 总被引:2,自引:0,他引:2
Tube thinning control without wrinkling occurring is a key problem urgently to be solved for improving the forming qualities in numerical control (NC) bending processes of large-diameter Al-alloy thin-walled tubes (AATTs). It may be a way solving this problem to exert axial compression loads (ACL) on the tube end in the bending. Thus, this article establishes a three-dimensional (3D) elastic-plastic explicit finite element (FE) model for the bending under ACL and has its reliability verified. Through a multi-index orthogonal experiment design, a combination of process parameters, each expressed by a proper range, for this FE model is derived to overcome the compression instability on tube ends. By combining the FE model with a wrinkling energy prediction model, an in-depth study is conducted on the forming characteristics of large-diameter AATTs with small bending radii and it can be concluded that (1) The larger the tube diameters and the smaller the bending radii, the larger the induced tangent tension stress zones on tube intrados, by which the tube maximum tangent compression stress zones will be partitioned in the bending processes; thus, the smaller the ACL roles in decreasing thinning degrees and the larger the compression instability possibilities on tube ends. (2) The tube wrinkling possibilities under ACL are larger than without ACL acting in the earlier forming periods, and smaller in the later ones. (3) For the tubes with a size factor less than 80, the ACL roles in decreasing thinning degrees are stronger than in increasing wrinkling possibilities. 相似文献
130.