异型孔空心叶片壁厚检测的试验研究

发动机叶片的结构型式和制造误差，直接影响发动机的性能和使用寿命。运用超声波法和电涡流法，对两种不同材料和形式的试件进行了试验。电涡流法受到探头直径和试件几何尺寸的影响，测量误差大，超声波法由于存在测量盲区，测量厚度的下限受到限制。但测量值与实际值相关，若对探头加以改进，用于异型孔空心叶片壁厚检测是可行的。     

行星际空间MHD模拟激波跃变关系分析

分析了模拟得到的可以传播到1AU以远的日地空间磁流体力学激波与Rankine-Hugnoniot跃变关系的符合程度．通过对模拟激波的结构及其在传播过程中的演化进行的分析，提出了模拟激波的定位方法；基于所提出的定位方法，利用向长青提出的确定MHD激波局地参数的方法计算了模拟得到的激波与Rankine-Hugnoniot跃变关系的偏差．结果表明在激波传播到100Rs以后，激波对中前向快激波与Rankine-Hugnoniot关系的符合达到很高的程度，相对误差在10^-2数量级以内；并且在激波传播到150 Rs以后，相对误差在10^-3数量级以内．这个结果说明文中所使用的有限差分数值格式能较好地模拟激波．     

飞机壁板结构的声疲劳计算及试验

 <正> 飞机结构所承受的噪声载荷声压级超过130dB时,经较长时间激励,往往在噪声诱导应力较大的区域里产生疲劳破坏。而在各种类型的结构件中声疲劳破坏的相对发生率以蒙皮壁板结构为最高。 本文采用矩形铝合金平板来模拟蒙皮壁板结构,对其进行了声疲劳寿命计算与试验研究.     

Transonic buffet control research with two types of shock control bump based on RAE2822 airfoil

Current research shows that the traditional shock control bump (SCB) can weaken the intensity of shock and better the transonic buffet performance.The author finds that when SCB is placed downstream of the shock,it can decrease the adverse pressure gradient.This may prevent the shock foot separation bubble to merge with the trailing edge separation and finally improve the buffet performance.Based on RAE2822 airfoil,two types of SCB are designed according to the two different mechanisms.By using Reynolds-averaged Navier-Stokes (RANS) and unsteady Reynolds-averaged Navier-Stokes (URANS) methods to analyze the properties of RAE2822 airfoil with and without SCB,the results show that the downstream SCB can better the buffet performance under a wide range of freestream Mach number and the steady aerodynamics characteristic is similar to that of RAE2822 airfoil.The traditional SCB can only weaken the intensity of the shock under the design condition.Under the off-design conditions,the SCB does not do much to or even worsen the buffet performance.Indeed,the use of backward bump can flatten the leeward side of the airfoil,and this is similar to the mechanism that supercritical airfoil can weaken the recompression of shock wave.     

Satellite launch vehicle effect on the Earth’s lower ionosphere: A case study

The effect of the rocket exhaust products on the D-region of the ionosphere is investigated with the help of Very low frequency (VLF) electromagnetic wave propagation characteristics within the Earth-ionosphere waveguide. The changes in the electron density profile are computed from the observed VLF signal amplitude perturbations about 3 dB during the rocket launch. We find a localized electron depletion in the lower ionosphere at an altitude of around 58 km, that is thought to be originated by the attachment of ionospheric ion and molecular hydrogen along with water molecule in the exhaust product of first stage burn of Geosynchronous Launch Vehicle (GSLV) rocket at the time of GSLV launched from Sriharikota, India, on 27 August 2015 at 11:22 UT (16:52 IST). The ionospheric depletion perturbed the navigational VLF signal (VTX = 17 kHz) 134 s after the launch of the GSLV rocket.     

Numerical investigation on flow nonuniformity-induced hysteresis in scramjet isolator

Numerical simulation and theoretical analysis were conducted to study the hysteresis inside scramjet isolator during the reciprocating process of back pressure variation. It is revealed that only a regular reflection is theoretically possible for two leading shocks when the inflow Mach number is greater than 2.0, and no hysteresis can occur in the transition between shock reflection types. Nevertheless, wall suction, gas injection, and background waves cause non-uniformity of the incoming flow and would make hysteresis possible. Besides the classical hysteresis in the transition between shock reflection, new kinds of hysteresis were found in both the deflection angle of separated boundary layer and the location of the shock train. Moreover, the occurrence of hysteresis in the deflection angle of the separated boundary layer is accompanied with the shock reflection hysteresis. In the case with background waves or gas injection, hysteresis in the starting position of leading shock was observed too. As back pressure decreases, the leading shock does not follow the same path as that as the back pressure increases, and it is anchored at the location where the background shock or the injection interacts with the leading shock. It is inferred that, if two strong adverse pressure gradient regions move towards and interact with each other, hysteresis will take place when they start to separate.     

Effect of blade tip winglet on the performance of a highly loaded transonic compressor rotor

The tip leakage flow has an important influence on the performance of transonic com-pressor. Blade tip winglet has been proved to be an effective method to control the tip leakage flow in compressor, while the physical mechanisms of blade tip winglet have been poorly understood. A numerical study for a highly loaded transonic compressor rotor has been conducted to understand the effect of varying the location of blade tip winglet on the performance of the rotor. Two kinds of tip winglet were designed and investigated. The effects of blade tip winglet on the compressor over-all performance, stability and tip flow structure were presented and discussed. It is found that the interaction of the tip winglet with the flow in the tip region is different when the winglet is located at suction-side or pressure-side of the blade tip. Results indicate that the suction-side winglet (SW) is ineffective to improve the performance of compressor rotor. In addition, a significant stall range extension equivalent to 33.74% with a very small penalty in efficiency can be obtained by the pressure-side winglet (PW). An attempt has been made to explain the fundamental mechanisms of blade tip winglet in detail.     

展向振荡对激波/湍流边界层干扰的影响

周期振荡作为一种有效的壁面流动控制手段受到广泛关注,而其对激波/湍流边界层干扰的影响目前鲜有研究。本文采用高精度直接数值模拟（DNS）方法对马赫数2.9、12°激波入射角、强振荡下的激波/湍流边界层干扰进行了系统研究。通过与无振荡工况的定量比较,揭示了展向强振荡对干扰区内复杂流动结构的影响规律及作用机制,如分离泡尺度、物面压力脉动非定常特性、物面剪切的非定常特性及统计特征等。研究发现：在展向强振荡作用下,分离点位置提前,间歇区长度增大;同时由于分离泡内强黏性耗散的影响,展向振荡的穿透高度约为分离泡高度的4%,因而对流动结构不会产生实质影响。但展向强振荡会对壁面附近流动造成显著影响,如强振荡诱导的壁面展向速度远大于流向速度,造成流向剪切与展向剪切之间夹角的概率密度函数峰值从0°偏移到80°~90°之间。物面压力及剪切本征正交分解分析表明,展向振荡会导致模态能量从低阶模态向高阶模态转移,降低低频运动的能量占比,增强再附后Görtler涡等壁面附近旋涡结构的强度。     

超声速膨胀角入射激波/湍流边界层干扰直接数值模拟

为了揭示膨胀效应对激波/湍流边界层干扰区内复杂流动现象的影响规律,采用直接数值模拟方法对来流马赫数2.9、30°激波角的入射激波与10°膨胀角湍流边界层相互作用问题进行了数值研究。系统地探讨了激波入射点分别位于膨胀角上游、膨胀角角点和膨胀角下游3种工况下膨胀角干扰区内若干基本流动现象,如分离泡、物面压力脉动及激波非定常运动、湍流边界层统计特性和相干结构动力学过程等。结果表明,激波入射点流向位置改变对分离区流向和法向尺度的影响显著,尤其是当激波入射点位于角点及其下游区域。研究发现,膨胀角干扰区内物面压力脉动强度急剧减小,分离区内压力波向下游传播速度将降低而在膨胀区内将升高,膨胀效应极大地抑制了分离激波的低频振荡运动。相较于入射激波与平板湍流边界层干扰,入射激波流向位置改变对膨胀角再附区速度剖面对数区及尾迹区影响显著,将导致其内层结构参数升高而外层降低,近壁区内将呈现远离一组元湍流状态的趋势。此外,流向速度脉动场本征正交分解分析指出,主模态空间结构集中在分离激波及剪切层根部附近而高阶模态以边界层内小尺度正负交替脉动结构为主。低阶重构流场结果表明,前者对应为分离泡低频膨胀/收缩过程而后者表征为分离泡高频脉动。     

膨胀效应对激波/湍流边界层干扰的影响

采用直接数值模拟方法对来流马赫数2.9,30°激波角的入射激波与膨胀角湍流边界层干扰问题进行了数值研究。入射激波在壁面上的名义入射点固定在膨胀角角点,膨胀角角度分别取为0°、2°、5°和10°。通过改变膨胀角角度,考察了膨胀效应对干扰区内复杂流动现象的影响规律和作用机制,如分离泡、物面压力脉动特性、膨胀区湍流边界层和物面剪切应力脉动场等。研究发现,膨胀角角度的增大使得分离区流向长度和法向高度急剧降低,尤其是在强膨胀效应下分离泡形态呈现整体往下游偏移的双峰结构。物面压力脉动功率谱结果表明,膨胀角为2°和5°时,分离激波的非定常运动仍表征为大尺度低频振荡,而膨胀角为10°,强膨胀效应极大地抑制了分离激波的低频振荡,加速了下游再附边界层物面压力脉动的恢复过程。膨胀区湍流边界层雷诺剪切应力各象限事件贡献和出现概率呈现逐步恢复到上游湍流边界层的趋势,Görtler-like流向涡结构展向和法向尺度变化剧烈,同时在近壁区将诱导生成大量小尺度流向涡。此外,物面剪切应力脉动场的本征正交分解分析指出,膨胀效应的影响体现在低阶模态能量的急剧降低从而使得高阶模态的总体贡献相对升高。