Experimental investigation of shock-buffet criteria on a pitching airfoil

An experimental investigation of the shock-buffet phenomenon subject to unsteady pitching supercritical airfoil around its quarter chord has been conducted in a transonic wind tunnel. The model was equipped with pressure taps connected to the fast response pressuretransducers. Measurements were conducted at different free-stream Mach number from 0.61 to0.76. The principle goal of this investigation was to experimentally discuss the shock-buffet criterion over a SC(2)-0410 supercritical pitching ...     

Trailing-edge shock loss control with self-sustaining synthetic jet in a supersonic compressor cascade

To effectively reduce the loss of strong shock wave at the trailing edge of the supersonic cascade under high backpressure, a shock wave control method based on self-sustaining synthetic jet was proposed. The self-sustaining synthetic jet was applied on the pressure side of the blade with the blow slot and the bleed slot arranged upstream and downstream of the trailing-edge shock,respectively. The flow control mechanism and effects of parameters were investigated by numerical simulation. The res...     

一种导致压电式冲击传感器零漂原因分析及抑制措施

冲击加速度传感器输出零漂是影响传感器使用的重要特性，对零漂问题探索由来已久。根据冲击传感器输出信号特点，从传感器模型到传感器与变换电路角度进行了分析，结合传感器安装频响与冲击信号之间的关系，得出高频冲击信号在传感器安装谐振频率处被放大导致传感器零漂的结论。通过理论推导与实际传感器输出结果对比，验证了理论推导的正确性。最后，对零漂抑制措施以及实际作用结果进行了阐述。     

Oblique shock train motion based on schlieren image processing

In this paper, shock train motion in a Mach number 2.7 duct is studied experimentally, and large numbers of schlieren images are obtained by a high-speed camera. An image processing method based on Maximum Correlation Detection (MCD) is proposed to detect shock train motion from the schlieren images, based on which the key structures, e.g., separation positions and separation shock angles on the top and bottom walls, can be analysed in detail. The oscillations of the shock train are generated by rhombus and ellipse shafts at various excitation frequencies. According to the analysis of MCD results, the distributions of the frequency components of shock train oscillation generated by the two shafts are distinctly different, in which the motion generated by the ellipse shaft is much smoother; shock train motion is mainly characterized by the oscillation of separation position while the separation shock strength is not so sensitive to downstream disturbance; there is a hysteresis loop relation between the downstream pressure and separation position.     

Symmetric Mach reflection configuration with asymmetric unsteady solution

Symmetric Mach reflection in steady supersonic flow has been usually studied by solving a half-plane problem with the symmetric line treated as reflecting surface, thus losing the opportunity to discover antisymmetric flow structures. Here in this paper we treat this problem as an entire-plane problem. Using an unsteady numerical approach, we find that the two sliplines exhibit antisymmetric unsteadiness if the Mach stem height is small while the flow remains symmetric if the Mach stem height is large. The mechanism by which disturbance, generated in the downstream of the flow duct between the two sliplines, propagates upstream is identified and it is also shown that the interaction between the transmitted expansion waves and the sliplines increases the amplitude of the unstable modes. The present study suggests a new type of compressible jet that deserves further studies.     

Hypersonic shock wave and turbulent boundary layer interaction in a sharp cone/flare model

A direct numerical simulation of hypersonic Shock wave and Turbulent Boundary Layer Interaction(STBLI) at Mach 6.0 on a sharp 7° half-angle circular cone/flare configuration at zero angle of attack is performed. The flare angle is 34° and the momentum thickness Reynolds number based on the incoming turbulent boundary layer on the sharp circular cone is Re_θ = 2506. It is found that the mean flow is separated and the separation bubble occurring near the corner exhibits unsteadiness. The Reynolds analogy factor changes dramatically across the interaction, and varies between 1.06 and 1.27 in the downstream region, while the QP85 scaling factor has a nearly constant value of 0.5 across the interaction. The evolution of the reattached boundary layer is characterized in terms of the mean profiles, the Reynolds stress components, the anisotropy tensor and the turbulence kinetic energy. It is argued that the recovery is incomplete and the near-wall asymptotic behavior does not occur for the hypersonic interaction. In addition, mean skin friction decomposition in an axisymmetric turbulent boundary layer is carried out for the first time. Downstream of the interaction, the contributions of transverse curvature and body divergence are negligible, whereas the positive contribution associated with the turbulence kinetic energy production and the negative spatial-growth contribution are dominant. Based on scale decomposition, the positive contribution is further divided into terms with different spanwise length scales. The negative contribution is analyzed by comparing the convective term, the streamwise-heterogeneity term and the pressure gradient term.     

星箭分离减冲击环结构优化设计

针对星箭分离过程，建立了减冲击环结构模型，并分析了该结构的减冲原理。利用冲击响应谱的时域合成算法计算获得符合冲击谱规范的时域载荷，并以此作为结构优化设计中动力学模型的输入载荷工况。以减冲击环的连续层数、单层支撑块数、连续层厚度、支撑块层高度以及环的外半径和内半径6个结构参数为设计变量，以减冲效果和结构强度、刚度为约束，以质量最轻为目标，建立减冲击环的结构优化设计模型，这是一包含离散变量和连续变量的混合优化问题。为了在跨平台下求解该混合优化问题，采用代理模型策略和自适应模拟退火算法求解，并在最优点处开展结构性能对设计变量的敏度计算，对计算结果进行了分析评估。本研究对强冲击动力学环境下的航天器结构分析与设计有一定的指导意义。     

FSW和VP-TIG焊接箱底的力学特征分析

针对纵缝采用搅拌摩擦焊、环缝采用VP-TIG熔焊工艺的箱底进行液压试验,并在试验过程中监测各典型焊缝位置的应变响应,结果显示箱底上搅拌摩擦焊缝和熔焊焊缝交叉形成的"T"型接头区域在试验中最先进入屈服,说明该位置材料的屈服强度较低,是箱底承载的薄弱环节。     

Influence of alumina abrasive tool wear on ground surface characteristics and corrosion properties of K444 nickel-based superalloy

K444 nickel-based superalloy is an important material to manufacture the gas turbine due to its excellent mechanical properties at high temperatures and corrosion resistance. Currently,grinding is the mostly used method for the surface finish of the K444 alloy components. However,few studies worked on the effects of the abrasive tool wear on the ground surface characteristics and corrosion properties of K444 alloy. This study uses two different-type alumina abrasive tools, i.e.,white alumina(WA)...