复合固体推进剂的高能化

本文评述了国外固体推进剂近年来向高能化方向发展的三个主要动向:HTPB推进剂的高固体及硝胺化;丁羟之后的新品种——NEPE推进剂;Be、B、叠氮化物等高能组分的研究等.对我国固体推进剂的发展方向提出了建议.     

先进的变载吸能器

传统的定载吸能器以50百分位男性乘员满足95％生存率为条件设计，它不能为全体乘员提供保护，变载吸能器能够根据乘员重量而调节动作载荷，为全体乘员提供最合理的保护，同时可以大大降低吸能器的冲击行程。     

吸力面翼刀对压气机叶栅内二次流的影响

1引言在叶轮机械叶栅内流动控制中,可以通过在叶片吸力面、端壁上安装翼刀或隔片,控制二次流的发展,降低二次流损失,其中将翼刀加装在吸力面上的控制方式即为吸力面翼刀控制技术。吸力面翼刀主要是通过阻断端壁附面层和叶片吸力面附面层近端壁处低能流动沿吸力面的展向迁移来对     

Topological defects and highest energy cosmic and gamma rays

In this paper we review the hypothesis that a substantial part of the cosmic ray flux observed above about 10¹⁹ eV may be produced by decaying or annihilating topological defects left over from phase transitions in the early universe at grand unification energy scales ( 10¹⁶ GeV). Possible signatures of cosmic ray producing defect models are discussed which could be tested experimentally in the near future. We thereby focus on model independent universal spectral properties of the predicted particle fluxes.     

华东地区围护结构节能研究

根据南京市的典型年逐时气象参数，对于该市的某一座高层建筑物，应用自编的逐时动态负荷模拟程序，输入围护结构（窗户、墙体和屋顶）相关的物理参数及其与周围环境的关系（地点及朝向等），计算围护结构冬季采暖期散热量及夏季制冷得热量。结果表明，采用双层塑窗代替单层塑窗，使用节能墙体代替传统墙体能够使得冬季围护结构传散热量减少51％，夏季围护结构总得热量减少46％。因此，这一结果为华东地区建筑节能技术提供了理论依据。     

钝体燃烧器后能量逆转和紊流参数的数学模拟

本文用非定常数值法研究了钝体燃烧器后的紊流参数分布和能量逆转,并对Boussinesq的雷诺应力模式和双方程k-ε紊流模型提出了改进方案。这样不仅计算出了能量逆转区,而且紊流参数分布也与实验相符。     

五元素风帆的试验研究

用正交试验与系列试验相结合的方法,研究了五元素风帆的气动特性及其各参数之间的最佳配合问題。设计的4个五元素风帆,均是由3个固定小翼、2个活动小翼及上下两块制流板所组成,但小翼的形状及分布曲线不同。 通过风洞试验,得到了各个风帆攻角与两个活动小翼转角之间的最佳配合,并对各帆的气动特性作了比较。试验结果表明,在最佳配合状态下,4个帆的升力系数可分别达到2.64、2.87、2.69和2.08,均比常规帆有较大的增长;而且,只要打开活动小翼,就能释放大部分风能,从而保证船舶在大风中的安全,这些帆的结构并不复杂,是具有广泛应用前景的高效帆具。     

一般硬化材料弹塑性旋转盘的变分解法

首先在小弹塑性范围内用应变的奇次四项式相当精确地拟合一般硬化材料的拉伸曲线;再在体积不变条件下用弹性位移场的已知模态和一待定幅值构成弹塑性位移场;最后用势能原理确定该幅值而得到封闭解。     

人工释能法求解线性代数方程组

本文建立求解线性代数方程组的人工释能法迭代格式,并给出该迭代格式收敛的充分必要条件和最佳释能时机,同时给出实现人工释能法的数值计算方法及其数值稳定性条件。     

Experimental investigation on silica dust lofting due to charging within micro-cavities and surface electric field in the vacuum chamber

The charged dust particles can be mobilized electrostatically by the repulsion between the adjacent grains and the surface electric field due to the incoming electron current and the charge accumulation within the micro-cavities. In this study, the experimental results of the initial vertical launching velocities and the maximum dust heights are compared with the estimated values for the lofted spherical dust grains by the patch surface charging equations. Silica particles with the sizes between <6 and 45?µm in radius are loaded on a graphite plate, and they are exposed to the electron beam with 450?eV energy under 4?×?10^?3?Pa vacuum chamber pressure. During the first set of the experiments, the dust samples are tested without an initial compression process and an additional horizontal electric field. Second, the dust samples are compressed by two different weights in order to increase the packing density under approximately 780.7?Pa and 3780?Pa. Finally, the dust grains are placed between the two parallel aluminum plates to apply approximately 2000?V/m and 4800?V/m horizontal electric field. A high-speed camera is used to record the transportation of the dust grains together with a microscopic telescope, and the results point out that the patch surface dust-charging model estimations are in agreement with the first experiments. On the other hand, the dust particles from the compressed samples are lofted with higher velocities than the estimations, and the number of the dust lofting observations decreases significantly, which demonstrates the importance of the micro-cavities and the increased charging requirement to overcome the contact forces. When the horizontal electric field is present, the initial vertical launching velocities are measured to be lower than the other experiments, which can be attributed to the decreased charging requirement for the dust lofting as a result of inter-particle collisions and rolling motion. According to the experimental results, the electrostatic dust transportation can be controlled not only by the ambient plasma and the solar irradiation on the airless planetary bodies, but also by the surface properties such as the contact surfaces between the dust grains, the number of the micro-cavities related to the packing density, and the presence of the horizontal electric field contributing to the external forces by other particle motions.