回流型脉冲爆震燃烧室工作特性分析

为了获得回流型脉冲爆震燃烧室在不同工作频率下的工作特性,通过试验和数值相结合的方法对该爆震室工作频率10~30Hz时的出口燃气总压、总温、流量变化规律以及该爆震室的增压能力进行了测试与计算分析。结果表明：出口燃气总压、总温具有极高的峰值和较高的平台区,其工作频率10~30Hz时,压力平台值为0.36~0.91MPa,时均温度为710~1270K。此外,该爆震室排气流量十分集中,以10Hz为例,在一个爆震循环的16%时间内,排出了整个循环60.5%的燃气。为此对出口燃气总压进行质量加权平均,发现该爆震室的增压比随工作频率的增加而降低,在2.05~2.37。     

Experimental characteristics of a two-electrode plasma synthetic jet actuator array in serial

Plasma Synthetic Jet (PSJ) actuators have shown wide and promising application prospects in high-speed flow control, due to their advantages including high exhaust speed, wide frequency band, rapid response, and non-moving components. Although previous studies on PSJ actuators are abundant, most of them have focused on the performance of a single actuator. However, in practice, an actuator array is very necessary for large-scale aerodynamic actuation on account of the small affected area of a single PSJ. In this paper, the characteristics of a two-electrode plasma synthetic jet actuator array in serial are investigated experimentally. Compared to a parallel actuator array, the serial actuator array requires simpler power supply design and is much easier to realize. High-speed photography of the discharge evolution, voltage-current measurement, and shadowgraphy visualization are used in the investigation. Experimental results show that, for the serial actuator array, weak discharges happen firstly between energized and suspending electrodes, and then a strong pulse arc discharge is triggered. The breakdown voltage in serial is irrelevant to such factors as the number of actuators, the maximum or minimum gap in serial, the connection sequence, etc. It is mainly determined by the sum of gaps. For serial actuators with the same anode-to-cathode spacing, the energy deposition is the same, and the jet is synchronous and similar. Because of the entrainment and merging of adjacent jet vortices, the jet front speed of an aligned synchronous jet array increases as the orifice distance decreases. To achieve the highest jet front velocity, the orifice of the actuator has an optimal diameter.     

超声速流动中功能梯度曲壁板的热气动弹性颤振机理

对高超声速环境中功能梯度曲壁板的热气动弹性颤振机理及分岔特性进行了研究。分别采用活塞理论和Eckert参考焓方法模拟气动力以及气动加热效应,在求解板内二维热传导方程以及考虑温升对材料物性影响的基础上,建立了一个气动加热-气动弹性双向耦合的功能梯度曲壁板的热气动弹性颤振模型。采用有限元方法对曲壁板控制方程进行了数值模拟,着重分析了不同拱高下曲壁板的分岔行为,探讨了拱高变化对曲壁板分岔图的影响,发现了曲壁板颤振三种典型的颤振行为,即:热屈曲、混沌以及规则振动。对初始拱高板厚比为1时,曲壁板的两种规则振动行为进行对比发现,随着马赫数的增大,气动加热效应所引起的热内力会使曲壁板的规则振动更加复杂,同时振动的主振型及频率均会发生变化。     

Brazing diamond grits onto AA7075 aluminium alloy substrate with Ag–Cu–Ti filler alloy by laser heating

The brazing of diamond is a promising way to fabricate grinding wheels for efficient machining and precision grinding. This work investigated the feasibility of bonding diamond grits onto Aluminium Alloy 7075 (AA7075) substrate with a Ag–Cu–Ti filler alloy via laser fusion brazing. The interfacial microstructures and the strength of the brazed diamond joints were studied. The cross-section of the brazed diamond joint consists of a molten filler alloy layer, a molten pool, a heat effect zone, a columnar crystal zone and an equiaxed crystal zone. Within the interface of the filler alloy/substrate metal, microstructures observed possibly were Ag(s.s), Al(s.s), TixAl, Al2Cu and Mg intermetallic compounds. A layer of TiC with a thickness of about 30–50 nm was found at the bonding interface of the diamond/filler alloy. The averaged peak shear force of the brazed joints was found to be approximately 39.8 N. The abrasion grinding test indicated that the diamond/AA7075 brazed joint was adequate for grinding. However, the pulled-off of grit was found to be the primary failure of this type of brazed joint. This work broadened the brazing diamond technique and the range of applications of brazed diamond wheels for efficient grinding.     

高超声速再入钝头体表面热流计算

采用边界层外缘无黏流场数值求解三维可压缩定常Euler方程,将所得物面压力分布作为边界层外缘条件,用于边界层内跟踪流线的轴对称比拟工程算法,计算高超声速有攻角再入钝头体的表面热流。某钝双锥算例结果表明:算得的表面热流与实验数据吻合很好。该方法较纯工程算法提高了精度,较数值求解整个流场Navi-er-Stokes方程节省计算时间,对准确计算全轨道飞行复杂形状高超声速飞行器表面的热流分布有一定价值,适宜高超声速飞行器方案设计阶段气动热环境预测的需要。     

污染空气对氢燃料超声速燃烧室性能的影响

采用纯净空气和污染空气来流下对比试验的方法,研究了飞行马赫数4条件下H2O和CO2污染组分对氢燃料超声速燃烧室性能的影响。对比试验中针对纯净空气来流和污染空气来流匹配了来流总温、总压、氧气摩尔分数和当量油气比。完成了0.53和0.42两种当量油气比条件下纯净空气来流和污染空气来流的氢燃料超声速燃烧试验,预定考察的H2O污染组分摩尔浓度分别有7.5%,18%和26%三种,CO2污染组分浓度有3.0%和7.5%两种。研究结果表明,H2O,CO2或H2O+CO2组合污染对燃烧诱导压升产生了明显的非线性抑制影响,直接将污染试验空气来流下的试验结果外推应用到飞行条件,可能导致供油量偏大、甚至进气道不启动;同时也影响了隔离段内燃烧诱导激波链结构,使燃烧工作模态趋向于超燃模态。     

高超声速滑翔飞行器表面加热特点研究

高超声速滑翔飞行器具有高机动和远程快速到达能力,是高超声速技术应用的前沿领域。快速准确地预测飞行器表面受热变化特征,对高超声速滑翔飞行器热防护系统设计十分重要。以基于锥导乘波构型的高超声速滑翔飞行器和跳跃飞行弹道为研究对象,对其表面不同特征区域的加热开展了快速预测方法研究;采用选用方法分析驻点辐射平衡温度随飞行弹道的变化规律;在弹道特征位置上针对飞行器前缘及上、下表面的加热情况进行分析,获得高超声速滑翔飞行器受热的整体特征,可为分区域选择热防护措施提供参考。     

航天器真空热试验用加热板的数值仿真

文章针对加热板在航天器热试验中的传热特点,利用Thermal Desktop软件建立了加热板和空间模拟器热沉的热数学模型,分析了电热丝数量、加热板材料和液氮管路布置方式对加热板升、降温时间和温度分布的影响;建立了模拟星、加热板和热沉的热模型,分析了加热板和星表间距对模拟星表面温度的影响。根据分析研究结果,提出了加热板设计及其在航天器热试验中的应用方法建议。     

基于PWM的挠性航天器分力合成主动振动抑制方法

分力合成主动振动抑制方法可以有效抑制挠性振动. 其利用几个相同或相似的随时间变化的分力, 按一定的规律沿时间轴排列合成为合力作为系统输入, 此合力可以在保证完成规定刚体运动的同时抑制掉指定的任意阶振动谐波. 对于使用常幅值力矩喷气执行机构的航天器, 应用脉宽调制(PWM)技术将符合分力合成方法的时间最优机动控制指令变化为常幅值力矩形式, 设计出常幅值的时间最优大角度机动策略. 数值仿真结果证实了方法的有效性.      

座舱蒙皮外表面气动加热的物理仿真研究

座舱蒙皮外表面气动加热的物理仿真是座舱热特性试验研究的重要基础。把平行射流理论应用于座舱蒙皮外表面气动加热的物理仿真,提出了气动加热物理仿真的新方法。该方法能够满足座舱动态热特性物理仿真的需要,且在人力、物力上较省。提出了用数学仿真控制座舱热特性试验的方法。这些方法已成功地应用于飞机座舱热载荷和热特性试验中。