Determination of optimal samples for robot calibration based on error similarity

Industrial robots are used for automatic drilling and riveting.The absolute position accuracy of an industrial robot is one of the key performance indexes in aircraft assembly,and can be improved through error compensation to meet aircraft assembly requirements.The achievable accuracy and the difficulty of accuracy compensation implementation are closely related to the choice of sampling points.Therefore,based on the error similarity error compensation method,a method for choosing sampling points on a uniform grid is proposed.A simulation is conducted to analyze the influence of the sample point locations on error compensation.In addition,the grid steps of the sampling points are optimized using a statistical analysis method.The method is used to generate grids and optimize the grid steps of a Kuka KR-210 robot.The experimental results show that the method for planning sampling data can be used to effectively optimize the sampling grid.After error compensation,the position accuracy of the robot meets the position accuracy requirements.     

Accuracy enhancement of the spherical actuator with a two-level geometric calibration method

This paper presents a two-level geometric calibration method for the permanent magnet （PM） spherical actuator to improve its motion control accuracy. The proposed actuator is com- posed of a stator with circumferential coils and a rotor with multiple PM poles. Due to the assembly and fabrication errors, the real geometric parameters of the actuator will deviate from their design values. Hence, the identification of such errors is critical for the motion control tasks. A two-level geometric calibration approach is proposed to identify such errors. In the first level, the calibration model is formulated based on the differential form of the kinematic equation, which is to identify the geometric errors in the spherical joint. In the second level, the calibration model is formulated based on the differential form of torque formula, which is to calibrate the geometric parameters of the magnetization axes of PM poles and coils axes. To demonstrate the robustness and availability of the calibration algorithm, simulations are conducted. The results have shown that the proposed two-level calibration method can effectively compensate the geometric parameter errors and improve the positioning accuracy of the spherical actuator.     

导弹电液伺服机构的模糊滑模变结构跟踪控制研究

为减小导弹电液伺服机构滑模变结构跟踪控制中的抖振,研究了一种模糊滑模变结构控制(FS-MVSC)方法。给出了模糊滑模控制器的构成,以及模糊化、模糊规则与推理、反模糊化处理的方法。在保持系统对参数变化和外干扰不确定强鲁棒性的同时,可使系统具有较优的动态响应和稳态控制精度。仿真结果表明,该控制方案有效。     

卫星遥感影像外方位元素的误差传播研究

高分辨率卫星遥感影像的几何定位精度与影像外方位元素精度密切相关.文章针对单景影像直接对地定位和立体影像前方交会定位两种典型情况,对影像各外方位元素在目标几何定位中的误差传播规律进行分析比较,相关结论可供卫星姿控及相机载荷设计方参考.     

基于交叠视场亮度优选算法的导航星库构建方法

星敏感器导航星库直接影响星图识别效率和姿态解算精度。分析了参与姿态解算的星颗数和亮度对姿态精度影响,在此基础上,提出了一种基于交叠视场亮度优选算法的星敏感器导航星库构建方法。将精度较高的Hipparcos星表作为基础星表,分析了星等、双星、自行、变星等对姿态精度的影响,将星库筛选成一个备选星库,生成覆盖全天球的交叠视场。每个拥有较多星的视场,都按照亮度优先原则从视场内的扇形区域中选择导航星,从而得到分布均匀的导航星库。结果表明:该方法能有效减小星敏感器导航星库规模,实现导航星在全天球和局部天区的均匀分布。     

公差原则中相关要求的计算问题

关于公差原则中的相关要求的计算问题 ,本文提出了两种方法 :计算法和图解法。运用这两种方法可以简化此类问题的计算过程 ,准确求得计算结果。     

锚固站数量及布局对导航星座自主定轨影响分析

针对导航星座自主定轨中的星座整体旋转问题,采用增设少量地面锚固站的方法可有效解决该问题。通过推导星地距离对卫星轨道升交点赤经的偏导数,证明了星地距离对卫星轨道升交点赤经可观。仅考虑在我国大陆范围内布设锚固站的条件下,仿真分析了锚固站数量以及布局对导航星座自主定轨精度的影响。仿真实验结果表明:采用3个以上的锚固站,即可有效控制星座整体旋转,在14d的仿真时段内卫星自主定轨精度保持4m以内;锚固站数量越多,自主定轨精度越高,但随着锚固站数量的增加,自主定轨精度改善程度越来越小;在保持4个锚固站的情形下,采用不同的锚固站布局方案,自主定轨精度并无明显差别。     

SAR performance-based fault diagnosis for electro-hydraulic control system: A novel FDI framework for closed-loop system

Model-based fault diagnosis serves as an efficient and powerful technique in addressing fault detection and isolation (FDI) issues for control systems. However, the standard methods and their modifications still encounter some difficulties in algorithm design and application for complex higher-order systems. To avoid these difficulties, a novel fault diagnosis framework based on multiple performance indicators of closed-loop control system is proposed. Under this framework, a so-called performance residual vector is constructed to measure the differences between the real system and the nominal model in terms of system stability, accuracy, and rapidity (SAR) respectively. The criteria for quantification, normalization of the SAR residuals and the explicit mappings between the thresholds and the required performance are given. FDI can be easily achieved simultaneously by monitoring the normalized residual vector length and direction in the SAR performance residual space. A case study on electro-hydraulic servo control system of turbofan engine is adopted to demonstrate the effectiveness of the proposed method.     

自相关分析法用于电离层TEC的内插评估

基于2004年实测数据的统计分析,将自相关分析法用于电离层TEC的缺值内插,并进行精度评估.采用上海地区GPS综合应用网和中国地壳运动GPS监测网数据,解算成电离层垂直TEC,对缺值进行了时序内插及评估.结果表明,缺值段内的插值误差一般中间较大,两侧较小,插值误差远小于均方差.将自相关分析法内插结果与线性插值法、抛物线法、三次样条法内插结果进行对比,发现对于缺值较多、变化较复杂的缺值段,其插值精度有明显的提高.采用自相关方法进行内插后,有效减小了由于缺值而引起的局部跳跃变化,可以比较准确地研究TEC变化特性.     

电磁测力系统研究

介绍了电磁测力系统中静磁场分析与优化、通电线圈位置控制方法及提高线性度的自校准方法。运用Maxwell 3D进行仿真计算,得到了相对优化的磁密及磁均匀性,通过控制通电线圈在磁场中位置及分段线性微分技术,提高了电磁测力准确度。构建了试验装置,对比试验数据表明,该研究措施对于提高电磁测力准确度取得了较好效果。