真空差压铸造微电脑控制系统的硬件设计

介绍了微电脑真空差压铸造控制系统的组成及工作原理,设计了压力检测电路、调节阀控制电路和串行通信接口电路,同时说明了系统的调试,并给出了实验结论。结果表明,该系统的硬件电路设计合理,运行情况良好,并达到了设计指标。     

Refined modeling and experimental verification of a torque motor for an electro-hydraulic servo valve

The Permanent Magnet Torque Motor (PMTM) is the key electro-mechanical conversion device in an Electro-Hydraulic Servo Valve (EHSV). In this work, a refined model of a PMTM is developed, considering the non-working air-gaps between the upper or lower yoke and the armature, the fringing effect at the limiting holes, and the nonlinear permeability of soft magnetic material. Based on the refined model, the influences of various factors on the calculation accuracy of the magnetic flux at the pole surfaces of the armature and the output torque are investigated. For verifying the validity of the refined model, a Finite Element Analysis (FEA) of the PMTM is conducted, and a test platform is constructed. Compared with existing models, the refined model can better reveal the intrinsic mechanism of the PMTM, and its calculations are more consistent with the FEA results. The experimental results of the armature deflection displacement show that the refined model can accurately describe the output characteristics of the PMTM.     

基于空基平台的激光通信技术研究和展望

深低温阀门多为常温设计，低温服役。宽温域引起的结构变形将诱发阀门导向卡滞、密封泄漏等安全问题。采用有限元分析方法获取阀门导向副配合部位变形量，提出迭代镜像补偿方法解决深低温服役的阀门导向副变形超差问题。经分析，在深低温工况下阀门配合间隙均超出设计允许值，导向行程最大时配合间隙减小17.95%至16.41 μm；补偿后导向副配合间隙变形量控制在1 μm内，满足深低温工况下阀门形状设计要求，验证了迭代镜像补偿方法的有效性。     

Pneumatic pressure control based on improved NMPC and its application to aeroengine surge simulation

In the semi-physical simulation of aeroengines, using the pneumatic pressure servo control technology to provide realistic pneumatic excitation to the sensors and electronic controller can improve the confidence of the simulation and reduce the test cost and risk. However, the existing methods could not satisfy the precise simulation of large-amplitude and high-frequency pulsating pressure during aeroengine surge. In this paper, a pneumatic pressure control system with asymmetric groups of the High-Speed on–off Valve (HSV) is designed, and an Improved Nonlinear Model Predictive Control (INMPC) method is proposed. First, the volumetric flow characteristics of HSV are tested and analyzed with Pulse Width Modulation (PWM) signal input. Then, a simplified HSV model with the volume flow characteristic correction is developed. Based on these, an integrated model for the whole system is further established and used as the prediction model in INMPC. To improve the computational speed of the rolling optimization process, the mapping scheme from control signal to PWM duty cycle of HSVs and the objective function with exterior penalty function are designed. Finally, the random step, sinusoidal and real engine surge data are set as the reference pressure in multiple comparative experiments to verify the effectiveness of the pressure tracking system.     

An architecture decomposition method of pneumatic catapult system based on OPM and DSM

The architecture strategy of the Unmanned Aerial Vehicle (UAV) pneumatic launch system should continue to evolve to adapt to complex and variable operating environments. Architecture representation, decomposition perspective, and cluster analysis play a vital role in the early phase of system architecture development. In order for the system to emerge anticipated and desirable intrinsic functional properties, an architecture decomposition method based on the Object-Process Methodology (OPM) and Design Structure Matrix (DSM) is put forward in this paper. The OPM is proposed to model the UAV launch process formally, and the matrix representation of the architecture of the pneumatic launch system is established. After the extension of the definition and operations of DSM, with the Idicula-Gutierrez-Thebeau Algorithm plus (IGTA + ) clustering algorithm, the transformation of the pneumatic launch system architecture from process decomposition to function decomposition is demonstrated in this paper. The analysis shows that the architecture decomposition of the pneumatic launch system meets the functional requirements of stakeholders.     

加工装配误差影响下偏转射流压力伺服阀静态特性分析

电液压力伺服阀是电液压力伺服控制系统的核心控制元件，广泛应用于航空、航天、军事等领域。区别于流量伺服阀，压力伺服阀在滑阀放大器的设计上多采用带有压力控制容腔的三通阀结构，不同的滑阀结构使得现有的偏转射流流量伺服阀仿真模型难以满足压力伺服阀性能预测的需求。本文基于AMESim平台建立了偏转射流压力伺服阀的仿真模型，并通过实验对仿真模型进行了验证，验证结果表明仿真模型能够准确地描述压力伺服阀的静态特性。最后，通过仿真模型分析了加工装配误差影响下压力伺服阀输出性能差异，仿真结果可为偏转射流压力伺服阀的性能预测和结构设计提供参考。