光学基片表面软质抛光胶体粒子的激光清洗

介绍了光学基片表面软质抛光胶体粒子激光清洗的基本方法、原理和实验装置,并通过对含有污染微粒的基片表面进行激光清洗,获得了高洁净表面的光学基片.     

现代飞机俯仰跟踪时诱发振荡预测分析

根据飞机纵向ＰＩＯ的特点，提出了预测分析ＰＩＯ所用的人－机闭环系统数学模型，其中飞机采用等效系统数学模型，驾驶员操纵采用ＭｃＲｕｅｒ模型，参数按地面人－机模拟飞行跟踪试验确定，集中介绍了四种飞机纵向ＰＩＯ预测准则，Ｓｍｉｔｈ－Ｇｅｄｄｅｓ准则，修正带宽准则，增益，相位裕度准则，Ｎｅａｌ－Ｓｍｉｔｈ原则，并提供了相应的计算方法。     

线性调频半导体激光衍射光栅干涉仪

介绍一种以线性调频半导体激光为光源的衍射光栅干涉仪。激光与光栅上衍射的±１级衍射波会合，由于有光程差而发生光拍频，测量拍频信号的相位移则可测得光栅的位移。设计了一种克服激光波长漂移和空气折射率变化影响的对称差动光路，使这种方法达到实用化的程度，分辨力达到纳米级。此外，还介绍了应用于接触干涉仪的实验情况。     

驾驶员诱发振荡的抑制方法

对电传操纵系统驾驶员诱发振荡（ＰＩＯ）的现象进行了分析，指出了舵回路速率饱和是造成ＰＩＯ的主要原因，并有针对对给出了一种非常规的用于解决饱和非线性问题的程序控制方法。这种方法主要是通过舵回路反馈的状态信息来改变驾驶杆输入信号的放大系数，从而达到有效抑制ＰＩＯ的目的，同时用Ｈｕｒｗｉｔｚ稳定判据进行了机理分析，最后给出了仿真验证结果，证明该方法是简单而有效的。     

飞机纵向驾驶员诱发振荡灵敏度分析

采用系统灵敏度理论，以修正的带宽准则，增益和相位裕度准则以及Ｎｅａｌ－ｓｍｉｔｈ准则等飞机纵向驾驶员诱发振荡（ＰＩＯ）预测准则作为系统指标，建立了参数变化对诱发振荡预测指标影响的灵敏度公式，以ＪＪ７飞机为例，给出了飞机，操纵系统及驾驶员参数上述指标影响的灵敏度，根据计算结果进行了ＰＩＯ参数敏度预测分析，同时与数值仿真结果进行了对比分析。     

尾涡数值模拟的曲涡元技术

连接涡线端点形成涡段并计算其对空间任意点的影响系数是尾迹分析的基本环节,称为涡元技术。本文推出圆弧涡元与其应用程序,并引进抛物拱弧涡元,以代替传统的直涡元。提供的曲涡元程序可方便地用于尾迹分析,算例表明曲涡元在提高精度减少计算量方面的先进性。     

Selective laser melting of Al–8.5Fe–1.3V–1.7Si alloy: Investigation on the resultant microstructure and hardness

This article presents the microstructure and hardness variation of an Al–8.5Fe–1.3V–1.7Si(wt%, FVS0812) alloy after selective laser melting(SLM) modification. Three zones were distinguished across the melting pool of the SLM-processed FVS0812 alloy: the laser melted zone(LMZ), the melting pool border, and the heat affected zone(HAZ) in the previously deposited area around the melting pool. Inside the LMZ, either an extremely fine cellular-dendritic structure or a mixture zone of the a-Al matrix and nanoscale Al_(12)(Fe,V)_3Si particles appeared. With a decreased laser beam scanning speed, the cellular-dendritic structure zone within the LMZ shrank significantly while the mixture zone expanded. The a-Al and Al_(12)(Fe,V)_3Si mixture zone was also observed in the HAZ, but another phase, submicron h-Al_(13)Fe_4 particles with rectangular or hexagonal shapes,formed along the melting pool border. Microhardness tests indicated that the hardness of the SLM-processed FVS0812 samples far exceeded that of the as-cast FVS0812 alloy.     

三维激光成像系统的点云模型真彩色处理方法

三维激光成像系统获得的点云数据精度高并且保有高精度的高程信息,然而特征信息不明显,没有保留全部的点和点的拓扑关系,无法直接判读地面物体;影像数据空间分辨率和精度低,并且缺少高程信息,然而其影像的特征连续,光谱信息丰富.因此,进行点云数据与影像数据融合方法的研究是目前三维激光成像系统研制的前沿性课题.针对点云数据与影像数据融合方法的研究,提出了一种三维激光成像系统点云模型真彩色处理的方法.实验结果显示,采用所提出的方法,不仅能够获得被扫描物体的位置信息和大小信息,而且能够得到被扫描物体的表面纹理细节信息.     

激光陀螺四位置寻北仪提高精度方法

为消除激光陀螺零偏和常值漂移的影响,采用四位置方案来实现高精度寻北。本文简述了单轴激光陀螺四位置寻北方案,给出了陀螺敏感轴与机体系前向偏差角标定方法,研究了寻北仪在倾斜基座下数据补偿算法。本文研究了由于在四个位置上电机转动不到位所引起的误差补偿算法。通过对寻北仪系统测试,采用电机转动不到位补偿后数据标准差降低了0.02º,激光陀螺寻北仪系统达到了高精度快速寻北的要求。     

Single track and single layer formation in selective laser melting of niobium solid solution alloy

Selective laser melting (SLM) was employed to fabricate Nb-37Ti-13Cr-2Al-1Si (at%) alloy, using pre-alloyed powders prepared by plasma rotating electrode processing (PREP). A series of single tracks and single layers under different processing parameters was manufactured to evaluate the processing feasibility by SLM, including laser power, scanning speed, and hatch distance. Results showed that continuous single tracks could be fabricated using proper laser powers and scanning velocities. Both the width of a single track and its penetration depth into a substrate increased with an increase of the linear laser beam energy density (LED), i.e., an increase of the laser power and a decrease of the scanning speed. Nb, Ti, Si, Cr, and Al elements distributed heterogeneously over the melt pool in the form of swirl-like patterns. An excess of the hatch distance was not able to interconnect neighboring tracks. Under improper processing parameters, a balling phenomenon occurred, but could be eliminated with an increased LED. This work testified the SLM-processing feasibility of Nb-based alloy and promoted the application of SLM to the manufacture of niobium-based alloys.