螺旋桨瞬态流场数值模拟

建立完善的螺旋桨绕流理论异常困难,这一方面是由于螺旋桨流场整体旋转性、非定常非线性、三维效应、气流粘性、涡桨干扰等原因;另一方面是螺旋桨流场的流场结构有待于进一步认知。文章采用CFD方法对螺旋桨的瞬态流场结构进行了重点研究,详细绘制了自启动瞬间直至充分发展的螺旋桨瞬态流场结构图及所受气动力的变化图,分析了流场变化特性及其对升力的影响。     

波音737-800飞机起飞性能随襟翼放出量的变化特点

波音737飞机与其他民用机型的一个不同之处是前缘缝翼在起飞时可以使用开缝状态。分析了波音737-800飞机下列四个起飞性能参数与襟翼放出量的关系:场地长度限制的最大起飞重量;爬升梯度限制的最大起飞重量;障碍物限制的最大起飞重量;起飞决断速度。结果显示这四个参数在襟翼放出量为10时出现异常,原因是前缘缝翼状态发生了变化。在襟翼放出量由5增大到10的过程中,前缘缝翼由不开缝的放出状态变成开缝的完全放出状态,降低了升力系数。     

现代民机新型灭火剂性能研究

对新型灭火剂研究背景和种类进行了简要介绍,对具有开发潜力的新型灭火剂的理化性能、毒性、腐蚀性、灭火性能、环保性能进行深入分析与研究。通过对新型灭火剂性能的研究,得出每种灭火剂的优缺点,筛选出适用于现代民机灭火系统的灭火剂。     

直升机防雷击措施研究

根据雷电附着特性和传递特性将直升机的雷击附着区划分为三个区,对每个雷击附着区的雷击强度及受影响程度进行了详细分析,并提出了相应的防雷击措施.     

航空发动机机载健康管理系统设计方法

为解决航空发动机机载健康管理系统正向设计流程不清晰、设计需求不明确、需求设计对应及追溯不规范的问题，在对 比国内外现有健康管理功能架构体系的基础上，结合正向设计中需求捕获、需求分析和功能分配，研究了由上到下的航空发动机 健康管理系统正向设计基本流程，开发了航空发动机健康管理正向设计流程平台，实现了机载功能架构的设计。引入基于模型的 系统工程思想，采用面向对象的工程设计思路，建立功能目标量化、功能描述、模块定义等图形化设计方法，验证了该设计方法在 硬件设计中的可用性。通过研究航空发动机机载健康管理系统设计方法并分析机载功能组成，建立了可扩展的流程平台，基于模 型设计方法建立了可用的硬件设计模型，可为航空发动机机载健康管理系统设计提供参考。     

Noise analysis of continuous GPS coordinate time series for CMONOC

The Crustal Movement Observation Network of China (CMONOC) is one of the major scientific infrastructures, mainly using Global Positioning System (GPS) measurements, to monitor crustal deformation in the Chinese mainland. In this paper, decade-long coordinate time series of 26 continuous GPS sites of CMONOC are analyzed for their noise content using maximum likelihood estimation (MLE). We study the noise properties of continuous GPS time series of CMONOC for the unfiltered, filtered solutions and also the common mode signals in terms of power law plus white noise model. In the spatial filtering, we remove for every time series a common mode error that was estimated from a modified stacking of position residuals from other sites within ∼1000 km of the selected site. We find that the common mode signal in our network has a combination of spatially correlated flicker noise and a common white noise with large spatial extent. We demonstrate that for the unfiltered solutions of CMONOC continuous GPS sites the main colored noise is a flicker process, with a mean spectral index of ∼1. For the filtered solutions, the main colored noise is a general power law process, indicating that a major number of the filtered regional solutions have a combination of noise sources or local effects. The velocity uncertainties from CMONOC continuous GPS coordinate time series may be underestimated by factors of 8–16 if a pure white noise model is assumed. In addition, using a white plus flicker noise model, the median values of velocity errors for the unfiltered solutions are 0.16 (north), 0.17 (east) and 0.58 (vertical) mm/yr, and the median values for the filtered solutions are 0.09 (north), 0.10 (east) and 0.40 (vertical) mm/yr.     

可形变人脸模型研究进展综述

正确理解和跟踪人脸是构建能够在复杂人类环境中自主工作的智能机器系统的首要和关键步骤，可形变模型通过统计学习方法给出对象形状的紧凑数学表示，是达成这一目标的重要手段。从机器学习和计算机视觉领域角度，对人脸图像的可形变模型构建这一研究课题的最新研究进展进行了综述。特别地，对其中涉及的关键问题进行了归纳，并建立了一个抽象的统一贝叶斯可形变模型；在此框架下，对标准的点分布模型PDM模型及其最新研究进展进行了回顾、对一些主要的方法进行了介绍、对这些方法优缺点进行了对比分析。     

航天器软件风险集成管理方法

为确保航天器软件产品功能、性能符合任务需求,安全、可靠地完成飞行任务,需要对其进行风险管理。文章首先介绍了软件风险管理理论研究现状;然后结合航天器软件强实时性、高可靠性和安全性、维护困难等问题,提出了基于系统集成思想的软件风险控制方法;最后以某航天器为例介绍了该套方法的应用成果。研究结果可为识别航天器软件风险,提高软件产品质量提供参考。     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

Materials selection for electronic enclosures in space environment considering electromagnetic interference effect

Using low power electronic devices for space applications to reduce the mass and energy consumption has lead to electromagnetic interference (EMI) problem. Electronic enclosures are used to shield electronic devices against EMI. In the past, electromagnetic shielding has been mainly the only criteria considered in electronic enclosure design. However, there are several structural and thermal requirements for selection of shielding materials which should also be taken into account. In this research work, three quantitative materials selection methods, i.e. Digital Logic (DL), Modified Digital Logic (MDL), and Z-transformation, are employed to select the best material from among a list of candidate materials. Composite and metallic electronic enclosures are explored and the best material is selected. Z-transformation method is applicable to both of the considered case studies while DL and MDL can only be used for solving one of them. Z-transformation method ranks aluminum as the first choice among various metallic materials. The wide range of Z-transformation application and its practical results confirm the superiority of Z-transformation method over DL and MDL methods.