基于双轴转位机构的激光捷联惯导系统在线标定方法研究

本文主要研究了在静基座条件下,利用双轴转位机构实现激光捷联惯导系统在线标定的两个问题：（1）推导了在线标定的一种误差参数模型,明确了模型成立的条件;（2）提出了设计多位置翻滚实验的位置编排原则。此方法具有实现简单、标定时间短、精度高的特点。     

Precise control of a magnetically suspended double-gimbal control moment gyroscope using differential geometry decoupling method

Precise control of a magnetically suspended double-gimbal control moment gyroscope (MSDGCMG) is of vital importance and challenge to the attitude positioning of spacecraft owing to its multivariable, nonlinear and strong coupled properties. This paper proposes a novel linearization and decoupling method based on differential geometry theory and combines it with the internal model controller (IMC) to guarantee the system robustness to the external disturbance and parameter uncertainty. Furthermore, by introducing the dynamic compensation for the inner-gimbal rate-servo system and the magnetically suspended rotor (MSR) system only, we can eliminate the influence of the unmodeled dynamics to the decoupling control accuracy as well as save costs and inhibit noises effectively. The simulation results verify the nice decoupling and robustness performance of the system using the proposed method.     

Graph-tree-based software control flow checking for COTS processors on pico-satellites

 This paper proposes a generic high-performance and low-time-overhead software control flow checking solution, graph-tree-based control flow checking (GTCFC) for space-borne commercial- off-the-shelf (COTS) processors. A graph tree data structure with a topology similar to common trees is introduced to transform the control flow graphs of target programs. This together with design of IDs and signatures of its vertices and edges allows for an easy check of legality of actual branching during target program execution. As a result, the algorithm not only is capable of detecting all single and multiple branching errors with low latency and time overheads along with a linear-complexity space overhead, but also remains generic among arbitrary instruction sets and independent of any specific hardware. Tests of the algorithm using a COTS-processor-based onboard computer (OBC) of in-service ZDPS-1A pico-satellite products show that GTCFC can detect over 90% of the randomly injected and all-pattern-covering branching errors for different types of target programs, with performance and overheads consistent with the theoretical analysis; and beats well-established preeminent control flow checking algorithms in these dimensions. Furthermore, it is validated that GTCGC not only can be accommodated in pico-satellites conveniently with still sufficient system margins left, but also has the ability to minimize the risk of control flow errors being undetected in their space missions. Therefore, due to its effectiveness, efficiency, and compatibility, the GTCFC solution is ready for applications on COTS processors on pico-satellites in their real space missions.     

NMOHEMS探头模型的制作及实验方法研究

NMOHEMS探头设计的有效性及其运动的CFD仿真计算方法都需要实验进行检验,利用计算机辅助设计结合三维快速成型技术制作了探头模型,在实验室水箱和水库两种环境下设计并完成了模型实验。其中,水箱实验利用有限实验水深,精确调整探头质量,利用高速摄像和图像处理技术,对多个较小质量探头的下沉运动进行了精密测量,详细的误差分析和修正后,获得不同质量探头运动的下落曲线和极限速度,以调整CFD仿真计算方法;水库实验利用自主研制的实验装置,对较大质量探头的下沉运动进行测量,误差修正后的极限速度为1．923m／s,验证了探头设计的有效性。     

Ground validation of space-borne satellite rainfall products in Malaysia

Precipitation studies globally is not only important to hydrological cycling, but also very crucial to satellite and terrestrial communication system designs. This work presents the validation of ground based rainfall measurement with TRMM products and GPCC data. The result shows that an error bias of ±15 % exists between the ground and satellite rainfall measurements. The study also shows that the TRMM 3B43 V6 is in good agreement with the rain gauge rainfall measurement with highest and lowest correlation coefficient of 0.9721 and 0.7791 respectively. Therefore, TRMM 3B43 V6 is recommended for use in lieu of the ground measurement in Malaysia and its environs, most importantly for sea and remote areas where rain gauge cannot cover.     

薄壁叶片叶型多工序加工检验模型建立方法

为了提高叶片的加工质量、降低叶片成品的废品率和加工成本，以航空发动机薄壁叶片数控铣削、抛光、振动光饰、喷丸强化的典型加工工艺为研究对象，提出了一种面向多工序的加工变形误差补偿方法及加工检验模型的建立方法。分析各工序的加工变形规律，将多工序变形误差作为一个整体，利用反变形误差补偿方法建立数控精铣工序的加工模型。图纸要求的理论模型只作为最终检验模型，而工序检验模型根据后续加工误差累加对最终检验模型修改得到。通过实例验证，该方法有效地降低了叶片工序检验结论的误判率，保证了工序检验合格及最终检验合格的要求。     

带通限幅器对锁相环噪声性能的影响

锁相环路中,在鉴相器前加上AGC（自动增益控制）,可以使环路性能在输入信噪比发生变化时保持稳定,带通限幅器也可以起到类似作用。尽管有一些文章对限幅器的性能作了研究,但是在PLL（锁相环）闭环条件下,鲜有文章分析其对环路噪声性能的影响。因此,文章以基本PLL环路的数学模型为基础,推导出PLL中分别加入相干AGC和带通限幅器后新的环路数学模型,以一阶PLL为例,计算和比较不同控制方式下环路相位误差均方值的变化,最后说明应当根据飞行任务的不同选择对环路更有利的控制方式。     

一种适用于曲面结构的机器人制孔误差在线补偿技术

针对工业机器人应用于飞机零部件自动钻孔时各项误差累积造成制孔精度差的问题，提出一种利用单应关系计算机器人驱动坐标三维偏差，以在线补偿机器人制孔精度的方法。首先利用外部测量设备建立机器人制孔系统中各坐标系关系；在标定阶段，通过以一定倾斜角度固联于机器人末端的相机拍摄一幅安装于制孔工作平面上与刀轴正对的平面标定板图像，并据此完成基于单应变换的手-眼关系标定；在实际制孔过程中，机器人在测距传感器及相机的辅助下，从基准孔理论坐标对应的姿态，不断调整至基准孔正上方理想位置，通过手-眼关系计算基准孔实际位置对应的机器人驱动坐标，然后根据一组基准孔的机器人三维驱动误差，计算三维驱动误差变换矩阵，据此获得这组基准孔邻域范围内各待钻孔的机器人驱动坐标补偿量，从而实现待钻孔定位误差补偿。以飞机结构实验件为对象进行了模拟制孔验证，实验结果表明，补偿前待钻孔三维综合定位误差和法向误差测量值范围分别为2.28~2.85 mm和2.09°~3.93°，平均为2.55 mm和3.30°，补偿后制孔最大误差分别不超过0.30 mm和0.21°，满足自动制孔位置精度要求。     

基于特征模型的Halo轨道维持控制

平动点，尤其是共线平动点轨道在未来深空探测活动中具有重要的应用价值，但由于共线平动点轨道不稳定，运行在其上的航天器在无控情况下将很快偏离标称轨道，因此在实际任务中，轨道维持必不可少。针对地月系L₂点附近的Halo轨道维持问题，首先在圆型限制性三体模型下，利用Richardson三阶近似解析解、微分修正以及打靶法获得了用于维持控制的标称轨道；然后设计了基于特征模型理论的黄金分割控制器用于速度跟踪以及PD控制器用于位置跟踪；最后分别在圆型限制性三体模型和双圆限制性四体模型下进行了仿真分析。结果表明：在两种模型下，位置和速度的跟踪精度分别优于100 m和0.003 m/s，但双圆限制性四体模型下所需总的速度增量比圆型限制性三体模型下所需总的速度增量高一个数量级。     

Preliminary analysis of the quality and positioning performance of BDS-3 global interoperable signal B1C&B2a

BeiDou-3 Navigation Satellite System (BDS-3) satellites are equipped with the new generation GNSS signals B1C and B2a, which support the interoperability with GPS and Galileo systems. In this study, the pseudo-range multipath error and carrier phase observation noise of the BDS-3 B1C and B2a signals were evaluated based on zero baseline measurements from the day of year (DOY) 113 to 116, 2020. Further, the precision and performance of the single point positioning (SPP) and precise point positioning (PPP) are assessed at 9 stations. This assessment manifests that the standard deviations (STDs) of the pseudo-range multipath error are about 0.09 ~ 0.22 m, while STDs of the carrier phase observation noise are about 0.075 mm. For the single-frequency SPP, its positioning precision is about 2.03 ~ 4.85 m and 3.29 ~ 10.73 m at the 99.99% confidence level in horizontal and vertical directions, respectively, while the dual-frequency SPP precision is about 1.92 ~ 8.02 m and 4.81 ~ 12.77 m in horizontal and vertical directions, respectively. For the daily static PPP, the convergence time is about 20 ~ 30 min, while the daily positioning precision can reach 1.38 ~ 4.42 cm and -1.31 ~ 4.34 cm in horizontal and vertical directions, respectively. In general, the quality and the SPP and PPP performance of the BDS-3 B1C&B2a signals are comparable to the GPS and Galileo.