“任务驱动”下的计算机专业课程教学实践与探索

本文总结了“任务驱动”在教学中的应用，提出了“任务”设计要全方位立体化进行考虑；评价要全方位多样化。指出了“任务驱动”必须与多种教学法优化组合，才能发挥其最大教学效率。     

A practical nonlinear robust control approach of electro-hydraulic load simulator

This paper studies a nonlinear robust control algorithm of the electro-hydraulic load simulator （EHLS）. The tracking performance of the EHLS is mainly limited by the actuator＇s motion disturbance, flow nonlinearity, and friction, etc. The developed controller is developed based on the nonlinear motion loading model. The problems of the actuator＇s disturbance and flow nonlinearity are considered. To address the friction problem, the friction model of the loading motor is identified experimentally. The friction disturbance is compensated using the obtained friction model. Therefore, this paper considers the main three factors comprehensively. The developed algorithm is easy to apply since the controller can be obtained just with one step back-stepping design. The stability of the developed algorithm is proven via Lyapunov analysis. Both co-simulation and experiments are performed to verify the effectiveness of this method.     

Parametric analyses for synthetic jet control on separation and stall over rotor airfoil

Numerical simulations are performed to investigate the effects of synthetic jet control on separation and stall over rotor airfoils. The preconditioned and unsteady Reynolds-averaged Navier–Stokes equations coupled with a k x shear stream transport turbulence model are employed to accomplish the flowfield simulation of rotor airfoils under jet control. Additionally,a velocity boundary condition modeled by a sinusoidal function is developed to fulfill the perturbation effect of periodic jets. The validity of the present CFD procedure is evaluated by the simulated results of an isolated synthetic jet and the jet control case for airfoil NACA0015. Then, parametric analyses are conducted specifically for an OA213 rotor airfoil to investigate the effects of jet parameters(forcing frequency, jet location and momentum coefficient, jet direction, and distribution of jet arrays) on the control effect of the aerodynamic characteristics of a rotor airfoil. Preliminary results indicate that the efficiency of jet control can be improved with specific frequencies(the best lift-drag ratio at F+= 2.0) and jet angles(40 or 75) when the jets are located near the separation point of the rotor airfoil. Furthermore, as a result of a suitable combination of jet arrays, the lift coefficient of the airfoil can be improved by nearly 100%, and the corresponding drag coefficient decreased by26.5% in comparison with the single point control case.     

月面高温下推力器可靠性试验

嫦娥五号着陆上升组合体落月后将经历月昼强红外辐射环境，由于推力器喷管导热影响，使推进剂管路与电磁阀面临高温环境，推进系统存在管路内氧化剂汽化和推力器性能下降甚至无法正常工作的问题，影响上升器月面起飞正常姿态控制。为了研究高温下推力器的工作性能，进行了高温下氟塑料阀芯与氧化剂相容性调研，提出了电磁阀和推力器可靠性增长及可靠性验证试验方法，分析了温度与电磁阀阀芯行程的关系，获取了高温环境下推力器的稳态及脉冲工作性能，在小子样条件下评估了推力器可靠性置信下限及月面起飞上升推进系统可靠度，通过月面高温排气及月面起飞上升姿态控制对研究结果进行了航天器在轨飞行验证，圆满完成了上升器月面起飞上升任务。所提出的研究方法及思路具有很好的工程适用性。     

进入中、韩两国的「日本製漢語」研究

「日本製漢語」是日本创造的汉字词,现已成为汉语和韩语的重要组成部分。分析了「日本製漢語」产生的原因和过程,探讨了「日本製漢語」进入中国和韩国的历史、政治和文化背景,并以「同形同義語」、「同形類義語」、「同形？義語」三个类型的「日本製漢語」,从数量、语义比较研究了它们在汉语和韩语中的差异及不同用法。     

小展弦比飞机非线性气动特性风洞与飞行相关性研究

在较大迎角范围，如何由风洞试验数据预计全尺寸小展弦比飞机的非线性气动特性，并与飞行值相关，始终是国际航空界致力解决的重大问题，本项研究采用风洞试验与工程计算相结合的方法，对支架，洞壁、进气，喷流，雷诺数及静弹性等影响相关性的诸因素予以修正，并计及配平影响，从而比较准确地预计出全尺寸收音机的非线性气动特性，预计值与试飞值相比较结果验证了本项研究的可靠性和实用性。     

综合效益模型求解方法的探讨

综合效益模型,是一种综合多因素影响的动态模型,它既包括一般效益模型,又考虑最优投资的优化效益模型。前者求解,可用解析法;后者求解,就不那么容易。文章分析了模型特征,认为是一个固定端点的最优控制问题,从而,选用格林定理（公式）能较好地求得满意解。     

叶片表面喷气对叶栅性能影响的试验研究

航空发动机的不断发展,使涡轮前的温度越来越高.尽管材料科研发展迅速,但仍赶不上温度提高的要求,涡轮叶片必须采用气冷,这就对涡轮气动性能带来了影响.本文介绍了用平面叶栅吹风试验方法研究气膜冷却叶栅在各种工况下对叶栅气动性能的影响,获得了许多有价值的结论.     

Reliability-based trajectory optimization using nonintrusive polynomial chaos for Mars entry mission

This paper presents the reliability-based sequential optimization (RBSO) method to settle the trajectory optimization problem with parametric uncertainties in entry dynamics for Mars entry mission. First, the deterministic entry trajectory optimization model is reviewed, and then the reliability-based optimization model is formulated. In addition, the modified sequential optimization method, in which the nonintrusive polynomial chaos expansion (PCE) method and the most probable point (MPP) searching method are employed, is proposed to solve the reliability-based optimization problem efficiently. The nonintrusive PCE method contributes to the transformation between the stochastic optimization (SO) and the deterministic optimization (DO) and to the approximation of trajectory solution efficiently. The MPP method, which is used for assessing the reliability of constraints satisfaction only up to the necessary level, is employed to further improve the computational efficiency. The cycle including SO, reliability assessment and constraints update is repeated in the RBSO until the reliability requirements of constraints satisfaction are satisfied. Finally, the RBSO is compared with the traditional DO and the traditional sequential optimization based on Monte Carlo (MC) simulation in a specific Mars entry mission to demonstrate the effectiveness and the efficiency of the proposed method.     

空间站常用元器件的霉菌敏感性研究

为研究空间站常用元器件的霉菌敏感性,选取空间站常用11大类元器件,针对霉菌对元器件的可能影响进行深入分析。基于空间站特定霉菌环境设计了加速试验方案,研究建立了基于元器件损伤程度的敏感等级分类方法,获取了不同元器件对霉菌的敏感性结果以及对应的敏感部位,为后续空间站用元器件质保工作的完善奠定基础。