涡扇发动机闭环控制系统设计仿真平台

航空发动机闭环控制系统的设计过程复杂且环节繁多,如果通过某平台综合多个设计过程,必然可以简化流程,提高效率.在总结国内外相关文献的基础上,针对民用涡扇发动机,在Matlab/Simulink下,利用模块化方法构建包含稳态控制器、过渡态控制器以及极限保护器的涡扇发动机闭环控制系统仿真平台,并对其进行仿真测试和硬件在回路实验.结果表明,所构建的仿真平台满足控制系统的性能和实时性要求,具有良好的工程适用性.     

民用客机E化趋势及其对航电系统的影响

国外飞机制造商为了提高飞机的市场竞争力,近年来大量应用信息技术对民用飞机的操作和运营过程进行优化,民用飞机出现了明显的E化趋势。阐述了民用客机E化的现状,从E化的利益相关方、路线及目标3个方面研究和判断了民用客机的E化趋势,并分析了E化趋势对航电系统的功能、架构及安保方面造成的影响。     

一种复杂空间飞网系统参数优化设计方法

由轻质软绳索编织而成的空间飞网是为非合作目标捕获而提出的空间系统概念,在空间碎片和废弃航天器处理方面具有很大的应用潜力。从平台抛射出后,飞网在空间形成不稳定的网形,且网形变化规律受初始参数设计的影响较大。针对空间飞网系统设计与试验中系统参数匹配问题,本文提出以容错值作为飞网展开性能的定量描述,从捕获任务的层面,建立面向捕获容错的空间飞网系统参数优化数学模型;以抓捕固定距离、确定大小的目标任务为算例,联合Isight优化平台与ANSYS/LS-Dyna求解,得到飞网系统最优参数匹配,算例仿真结果表明结果的适用性;最后,利用试验设计和极差分析方法验证最优点的稳定性。研究的模型与方法为开展空间飞网系统地面及空间试验等工程应用提供理论依据。     

针刺C/C复合材料拉伸强度及渐进失效数值预测

基于金相显微镜观测的针刺C/C复合材料细观结构,考虑材料内部纤维的真实分布,建立了针刺C/C复合材料单胞模型。采用Linde失效准则,考虑纤维渐进损伤对材料进行了刚度折减,通过引入周期性位移边界条件,对针刺C/C复合材料的拉伸破坏进行了有限元法（FEM）数值模拟,分析了单胞模型的渐进失效过程,并预测了材料的拉伸强度。开展了针刺C/C复合材料拉伸试验,采用扫描电子显微镜（SEM）观察了材料的断口形貌,数值预测结果与试验吻合良好。针刺C/C复合材料受拉伸载荷后发生准脆性断裂,拉伸应力-应变曲线呈双线性,0°无纬碳布发生纤维断裂和基体开裂破坏,90°无纬碳布出现横向基体劈裂,最终断裂发生在针刺纤维与面内无纬碳布交叉区域。     

临近空间飞行器信息系统一体化载荷平台

介绍了临近空间日趋受到各国的关注和研究、临近空间的概念以及临近空间飞行器的概况。从高超声速临近空间飞行器设计层面分析了临近空间飞行器信息系统多任务需求和现有设计的矛盾,指出研究临近空间飞行器一体化综合电子系统信号交链和多任务一体化协同技术是解决此矛盾的有效途径。通过对临近空间飞行器信息系统一体化载荷平台的研究,构建了采用冗余备份技术的包括信号处理模块、控制模块的统一开放的柔性系统平台架构。     

Parachute dynamics and perturbation analysis of precision airdrop system

To analyze the parachute dynamics and stability characteristics of precision airdrop system,the fluid–structure interaction(FSI) dynamics coupling with the flight trajectory of a parachute–payload system is comprehensively predicted by numerical methods.The inflation behavior of a disk-gap-band parachute is specifically investigated using the arbitrary Lagrangian–Euler(ALE) penalty coupling method.With the available aerodynamic data obtained from the FSI simulation,a nine-degree-of-freedom(9DOF) dynamic model of a parachute–payload system is built and solved to simulate the descent trajectory of the multi-body dynamic system.Finally,a linear five-degree-of-freedom(5DOF) dynamic model is developed,the perturbation characteristics and the motion laws of the parachute and payload under a wind gust are analyzed by the linearization method and verified by a comparison with flight test data.The results of airdrop test demonstrate that our method can be further applied to the guidance and control of precision airdrop systems.     

Prediction of cutting forces in ball-end milling of 2.5D C/C composites

Machining of carbon/carbon (C/C) composite materials is difficult to carry out due to its high specific stiffness, brittleness, anisotropic, non-homogeneous and low thermal conductivity, which can result in tear, burr, poor surface quality and rapid wear of cutters. Accurate and fast pre-diction of cutting forces is important for milling C/C composite materials with high quality. This paper presents an alternative cutting force model involving the influences of the directions of fiber. Based on the calculated and experimental results, the cutting forces’ coefficients of 2.5D C/C com-posites are evaluated using multiple linear regression method. Verification experiment has been car-ried out through a group of orthogonal tests. Results indicate that the proposed model is reliable and can be used to predict the cutting forces in ball-end milling of 2.5D C/C composites.     

A dimension reduced INS/VNS integrated navigation method for planetary rovers

Inertial navigation system/visual navigation system (INS/VNS) integrated navigation is a commonly used autonomous navigation method for planetary rovers. Since visual measurements are related to the previous and current state vectors (position and attitude) of planetary rovers, the performance of the Kalman filter (KF) will be challenged by the time-correlation problem. A state augmentation method, which augments the previous state value to the state vector, is commonly used when dealing with this problem. However, the augmenting of state dimensions will result in an increase in computation load. In this paper, a state dimension reduced INS/VNS integrated nav-igation method based on coordinates of feature points is presented that utilizes the information obtained through INS/VNS integrated navigation at a previous moment to overcome the time rel-evance problem and reduce the dimensions of the state vector. Equations of extended Kalman filter (EKF) are used to demonstrate the equivalence of calculated results between the proposed method and traditional state augmented methods. Results of simulation and experimentation indicate that this method has less computational load but similar accuracy when compared with traditional methods.     

含激波的湍流流动高精度大涡数值模拟方法

针对采用亚格子模型进行含激波的湍流流动模拟时会面临激波附近的精度损失问题,考虑从通过亚格子模型以及数值模拟方法两方面的改进来实现湍流流动大涡模拟的精度提高.大涡模拟采用了Yee及Sj(o)green (2009)提出的高阶低耗散方法.该方法采用自适应的流场探测器以控制计算中所需区域的数值耗散,并考虑对动力学模型采用在激波位置使用Sagaut和Germano(2005)提出的单边亚格子过滤器和(或)直接禁用亚格子项等方法加以改进.对于标准的马赫数1.5和3条件下的激波-湍流干扰问题,上述新方法相较于全区域采用亚格子模型的方法均表现出了相似的精度提升.同时实现的数值精度改进方案采用了Harten的亚单元分辨过程来定位和锐化激波,并在精确激波位置附近的网格点处采用了单边测试滤波.     

C/SiC复合材料反射镜研究进展

反射镜在空间光学系统中起着非常关键的作用,目前已发展到第四代C/SiC复合材料。C/SiC复合材料具有低密度、高模高强、结构设计灵活等优点,已成为非常重要的新型反射镜材料。本文对四代反射镜的特点进行了归纳和对比,对C/SiC复合材料反射镜的结构设计、几种常用的制备工艺进行了整理和总结,并对目前国内外的研究进展进行了综述。