超声速流中激波/湍流附面层干扰数值模拟

采用修正的B／L湍流模型以及多块结构化网格求解了二维N-S方程。分别对超声速流和高超声速流中的激波／湍流附面层干扰进行了数值研究。本文首先研究了进口马赫数为2．96的超声速流。计算结果准确预测了入射斜激波在平直壁面引起湍流附面层分离的流动特征：分离点的反射激波、分离包引起的膨胀扇以及再附点的反射激波。计算的壁面压力分布与实验值吻合较好，计算的分离区长度与实验值比较有一定误差。本文还对进口马赫数为9．22的高超声速流中压缩角引起的激波／湍流附面层干扰进行了数值研究。计算结果与实验结果吻合较好。     

CuAl2／Al复合材料的固相反应合成技术及与Al液的接触反应研究

研究了Ａｌ，Ｃｕ在真空状态下的纯固相接触反应情况，试验表明，Ａｌ粉、Ｃｕ粉在６００℃，保温６ｈ时，两者以完全发生反生成ＣｕＡｌ２（θ相），生成的θ相沿铝基体组织晶界分布并在结晶过程中具有择优取向特性，形成仅含沿晶界方向的主干与垂直于晶界的二次晶轴的树枝晶形貌。     

推力矢量和二元喷管

推力矢量是第四代战斗机获得过失速机动性的必要条件,而二元喷管又是推力矢量控制中性能较为优越的一类喷管。本文较全面地阐述了目前世界上推力矢量和二元喷管的发展和现况、二元喷管的构造和性能、二元喷管对改进飞机升阻特性和机动的作用。推力矢量能显著提高飞机在空战中的作战效率以及推力矢量控制所需的效能也在文中作了介绍。     

利用双目标优化寻求颤振抑制控制律

本文对一个三角机翼/外挂系统的颤振主动抑制进行了系统的研究。在理论上,对如何应用现代控制理论设计优化控制律进行了探讨;对非定常气动力拟合的Pade矩阵近似作了改进;提出了用理想极点和二次型性能指标进行双目标优化来确定加权矩阵的思想;在实现上,用状态观测器和单秩法极点配置两种方法设计了输出反馈控制律。风洞实验结果表明:用本文的方法所综合的控制律是合适有效的,成功地使机翼/外挂系统的颤振速度提高了15.7％,与理论计算结果吻合良好。     

A novel surrogate modeling strategy of the mechanical properties of 3D braided composites

In this paper, a surrogate-based modeling methodology is developed and presented to predict the elastic properties of three dimensional (3D) four-directional braided composites. Using this approach, the prediction process becomes feasible with only a limited number of training points. The surrogate models constructed using Finite Element (FE) method and Diffuse Approximation, reduce the computational time and cost for preparing experimental samples. In the FE model, multiscale method is applied to couple the computations of elastic properties at microscale and mesoscale. Subsequently, a parametric study is performed to analyze the effects of the three design parameters on the elastic properties. Satisfactory results are obtained via the surrogate-based modeling predictions, which are compared with the experimental measurements. Moreover, the predictions obtained from surrogate models concur well with the FE predictions. This study orients a new direction for predicting the mechanical properties based on surrogate models which can effectively reduce the sample preparation cost and computational efforts.     

基于网络的GPS时钟信号发布系统

从空管的实际应用出发,本次研究尝试以TCP Server/Client的模式进行GPS时钟信号的网络发布,通过这种方式实现多套系统灵活的时钟信号引接。     

基于B/S的空管自动化综合航迹显示系统的设计与实现

提出一种基于B/S的综合航迹显示系统,该系统通过解析空管自动化系统的综合航迹实现了在IE浏览器上对区域内的航迹的监视。系统实现主要包括三部分:一是综合航迹的接收,主要通过对同步串口卡的数据读取;二是对数据的数据库处理;三是对综合航迹的显示。系统实现了对MH4008003类数据的解析以及对空管自动化系统的地图解析,并且在IE界面上提供了航迹态势显示以及用户交互接口。     

抗辐射保偏光纤的制备及其特性研究

通过对保偏光纤进行光漂白与低温相结合处理的方式，来提高光纤的抗辐射性能。保偏光纤再经过1.0 kGy的高剂量预辐照处理后，其损耗会明显增大。随后采用980nm的激光对光纤进行光漂白处理,其损耗并没有发生明显变化。但是，处理后的样品在小剂量辐照条件下其光纤传输呈现先减小后增大的趋势。对于通过液氮进行冷处理的预辐照样品，其光纤传输损耗得到明显的降低，同时光纤经过小剂量辐照后的损耗同样也具有先减小后增大的现象。最后，将两种处理方式相结合，一方面可以有效地降低预辐照光纤的传输损耗，另一方面也使得保偏光纤在小剂量辐照的条件下，使其传输损耗具有减小的趋势，大大提高了保偏光纤在小剂量辐照条件下的抗辐照特性。     

Influence of TiB2 particles on machinability and machining parameter optimization of TiB2/Al MMCs

In situ formed TiB₂ particle reinforced aluminum matrix composites (TiB₂/Al MMCs) have some extraordinary properties which make them be a promising material for high performance aero-engine blade. Due to the influence of TiB₂ particles, the machinability is still a problem which restricts the application of TiB₂/Al MMCs. In order to meet the industrial requirements, the influence of TiB₂ particles on the machinability of TiB₂/Al MMCs was investigated experimentally. Moreover, the optimal machining conditions for this kind of MMCs were investigated in this study. The major conclusions are: (1) the machining force of TiB₂/Al MMCs is bigger than that of non-reinforced alloy and mainly controlled by feed rate; (2) the residual stress of TiB₂/Al MMCs is compressive while that of non-reinforced alloy is nearly neutral; (3) the surface roughness of TiB₂/Al MMCs is smaller than that of non-reinforced alloy under the same cutting speed, but reverse result was observed when the feed rate increased; (4) a multi-objective optimization model for surface roughness and material removal rate (MRR) was established, and a set of optimal parameter combinations of the machining was obtained. The results show a great difference from SiC particle reinforced MMCs and provide a useful guide for a better control of machining process of this material.     

基于T-S模糊模型的模糊大系统的混合滤波

针对非线性大系统内部过程参数的检测估计,采用连续模糊大系统模型,利用lyapunov定理和分布式处理方法,给出了模糊大系统的H2/H∞混合滤波器设计方法。该方法在保证滤波误差系统全局稳定的同时,具备了H2/H∞性能。通过求解线性矩阵不等式,可以得到滤波器参数。最后,用一个数值例子验证了该方法的正确性和有效性。