基于确定有限自动机实现MES的流程控制应用研究

简述确定有限自动机的基本概念,提出了应用确定有限自动机在MES中实现流程控制的思想.通过XML来构造确定有限自动机,并给出实现方法和实例.     

冲击-发散冷却火焰筒浮动瓦片三维壁温计算分析

论述了采用冲击-发散冷却技术的火焰筒浮动瓦片的传热计算分析方法, 以及传热数学模型和边界条件处理.并采用ANSYS程序的热分析模块对浮动瓦片的三维壁温场进行了计算.计算结果与试验结果进行了对比分析, 两者有较好的吻合性, 计算值与试验值的相对误差不大于6%.      

Unsteady flow phenomena associated with leading-edge vortices

This paper presents selected results from extensive experimental investigations on turbulent flow fields and unsteady surface pressures caused by leading-edge vortices, in particular, for vortex breakdown flow. Such turbulent flows may cause severe dynamic aeroelastic problems like wing and/or fin buffeting on fighter-type aircraft. The wind tunnel models used include a generic delta wing as well as a detailed aircraft configuration of canard-delta wing type. The turbulent flow structures are analyzed by root-mean-square and spectral distributions of velocity and pressure fluctuations. Downstream of bursting local maxima of velocity fluctuations occur in a limited radial range around the vortex center. The corresponding spectra exhibit significant peaks indicating that turbulent kinetic energy is channeled into a narrow band. These quasi-periodic velocity oscillations arise from a helical mode instability of the breakdown flow. Due to vortex bursting there is a characteristic increase in surface pressure fluctuations with increasing angle of attack, especially when the burst location moves closer to the apex. The pressure fluctuations also show dominant frequencies corresponding to those of the velocity fluctuations. Using the measured flow field data, scaling parameters are derived for design purposes. It is shown that a frequency parameter based on the local semi-span and the sinus of angle of attack can be used to estimate the frequencies of dynamic loads evoked by vortex bursting.     

表面贴有压电片的桁架结构系统静力可靠性分析(英文)

对表面贴有压电片的主动杆单元组成的桁架结构系统,在考虑电荷载和机械荷载联合作用的机电耦合效应时,利用力学原理,建立了静力分析的有限元模型。同时研究了压电杆元的破坏机理,给出压电杆单元破坏的判断准则。以材料的断裂强度、损伤电场强度、杆元的截面积和外荷载等为随机变量,建立了压电桁架结构单元的安全余量的表达式。并在此基础上,引入随机有限元法和结构系统可靠性理论,对该桁架结构系统进行可靠性分析。最后由算例说明本文方法的有效性。     

温度变化对振动信号传输的影响分析

针对高温振动测试过程中出现的信号传输不稳定问题,建立了热电耦合模型,研究了高温环境对信号稳定传输所产生的影响.在相关热电磁理论的基础上,采用有限元方法建立了分析模型,电信号传输过程中产生的焦耳热与对流换热的共同作用,造成了传输线的温升.依据电信号-温度灵敏度变化关系,得出了外部环境的对流换热系数变化影响电信号传输的规律,建立了相应的误差公式估算输入与输出电信号响应之间的关系.研究结果表明:输入信号有效值越大,导体温升越大,输出与输入电信号间的偏离误差越大.并进一步确定了电信号稳定性传输的影响因素,为提高高温环境下结构测试的准确性提供了有效方法.     

旋成体大迎角分离流的Euler方程数值模拟

用三维Euler方程计算旋成体的大迎角绕流,我们发现:亚声速自由流时,计算得到的是无分离流动,与实际的分离流不相符合,因而计算的法向力大大小于有分离的实验值;而当自由流为超声速,且横向自由流M数较高时,由于背风表面出现激波,无粘Euler方程的数值计算能自动捕捉到背风面上的分离涡,计算法向力与实验值接近。为了对亚声速自由流用Euler方程数值模拟大迎角旋成体背风面上分离涡,根据问题的物理图像,在假设的分离线上,提出强加Kutta条件的方法,成功地计算出有分离流动,使计算的法向力与实验值接近。     

辊弯成形仿真分析与参数优化(英文)

辊弯成形工艺是一种在常温下将平板金属材料通过连续转动的成形辊成形为所需截面的加工方法.本文通过有限元模型建立了一套避免重大产品质量缺陷的设计方法.通过对真实产品的仿真,在设计中考虑了两个辊弯成形主要缺陷,即边波和回弹.设计结果表明,该设计方法能够有效地控制这两大质量问题.     

Corner-milling of Thin Walled Cavities on Aeronautical Components

This article presents a mathematical model of helical end-milling forces through experimental identification of the cutting coefficients and analyzes the changes of corner-milling forces under different conditions. In allusion to the corner-milling process, the relationship between working parameters and the corner coordinates is investigated by way of combination of tool tracing and cutting geometrodynamics. The milling parameters are optimized by changing the coordinates of tool center and working parameters without altering cutting forces. By applying the optimized parameters to milling practice, a comparison is made to show the improved product quality. Based on these optimized parameters, a finite element method (FEM) program is used to compute deformation values of a workpiece's corner, which evidences few effects that optimized parameters can exert on the corner deformation.     

精确复现机翼摇滚运动的控制技术

为快速、精确地复现自由摇滚实验得到的机翼摇滚运动，在控制伺服电机的传统PID参数基础上增加了基准速度修正系数Kv，并将其视作PID参数的一部分，在此基础之上给出了一种PID参数的快速估计方法。利用该方法可以快速得到不同试验状态下控制伺服电机复现机翼摇滚运动的PID参数，提高了调试反馈控制量的效率。同时，发现在进行PID参数调节之前对速度时序曲线进行光滑化预处理，能为进一步进行PID调节打下坚实基础，提高电机驱动模型复现机翼摇滚运动的精度。最后，通过风洞试验对给出的方法进行了实验验证。     

SOLUTION OF 3-D TURBULENCE NAVIER-STOKES EQUATIONS USING HYBRID GRIDS

INTRODUCTIONWith the development of computer,consid-erable process has been made in the developmentof numerical methods for the solution of Navier-Stokes equations.However,most of these me-thods are impractical for complicated flows in adesign environment.The primary reason is thatwe can′t generate a suitable mesh easily for acomplicated configuration.Although there aremany techniques,such as structured grid or un-structured grid,which have been successfullyused for numerical simulation…