再入制导和弹道跟踪误差分析

新一代可重复使用运载器对再入制导提出了更高地要求。目前的空间运输系统证明基于阻力加速度的制导方法是行之有效的。其基本概念是跟踪基准阻力加速度包线，在飞行过程中可根据需要更新这个包线。跟踪适当的阻力加速度包线保证了飞行器可以飞行准确的距离达到目标，同时满足弹道约束。在横向上，我们可采用类似于美国航天飞机的倾斜反转逻辑或航向角跟踪技术。本文推导出了基于反馈线性化的控制算法，并将其应用于可重复使用运载器纵向和横向的制导。最后，我们分析了阻力加速度跟踪的误差。     

多模自适应目标图像跟踪

本文建立了图像序列中含加性和乘性两种噪声模型影响下的目标偏移值测量模型。并针对目标机动性，采用多模虑波器和两段卡尔曼虑波器对目标状态进行估值，有效抑制了各种噪声影响，又消除了显式的目标机动性检测，且有较高的实时性和较少的存储量等优点。     

无人机模拟训练系统中的实时飞行仿真

为了降低无人机的试飞成本,提高操纵手的技能,设计了一种模拟训练系统。介绍了该模拟训练系统的特点和构成,着重对系统中实时飞行仿真的各模块设计方法进行了研究。在DOS操作系统中用C语言实现飞行仿真软件,并讨论了软件实现中的模态切换等关键问题。通过飞行剖面仿真实验,证明该仿真系统可靠性高、实时性好。     

Estimation of sea surface temperature, wind speed and water vapor with microwave radiometer data based on simulated annealing

A method for estimation of sea surface temperature, ocean wind speed and water vapor with microwave radiometer data based on simulated annealing is proposed. The proposed method shows about 60% improvement of sea surface temperature estimation accuracy in comparison to the existing method using Newton’s iterative algorithm.     

航空绞车综合测量系统的设计与实现

简要介绍了航空绞车综合测量系统的功能、组成、工作原理及软硬件设计。     

高空高速无人飞行器热控制系统设计

针对飞行时间短、速度和高度变化快、表面温度波动大的无人飞行器UAV(Unmanned Aerial Vehicles)热控制系统设计难题,提出了一种可解决实际工程问题的热分析计算方法.即把热天工况、冷天工况和标准天工况作为设计/试验工况;采用参考温度法、高超音速工程预测法或计算流体动力学CFD(Computational Fluid Dynamics)数值模拟法,确定了飞行器表面温度分布,并把其作为后续热分析数学模型的外边界条件;分析结构热容量对瞬态热载荷的影响,建立与之相应的边值问题方程,并采用有限差分法求解;根据高空高速飞行特点及瞬态热载荷值,确定仪器设备舱调温系统方案.     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

Modeling novel methodologies for unmanned aerial systems–Applications to the UAS-S4 Ehecatl and the UAS-S45 Bálaam

The rising demand for Unmanned Aerial Systems(UASs) to perform tasks in hostile environments has emphasized the need for their simulation models for the preliminary evaluations of their missions. The efficiency of the UAS model is directly related to its capacity to estimate its flight dynamics with minimum computational resources. The literature describes several techniques to estimate accurate aircraft flight dynamics. Most of them are based on system identification. This paper presents an alternative methodology to obtain complete model of the S4 and S45 unmanned aerial systems. The UAS-S4 and the UAS-S45 models were divided into four sub-models, each corresponding to a specific discipline: aerodynamics, propulsion, mass and inertia, and actuator. The‘‘aerodynamic" sub-model was built using the Fderivatives in-house code, which is an improvement of the classical DATCOM procedure. The ‘‘propulsion" sub-model was obtained by coupling a two-stroke engine model based on the ideal Otto cycle and a Blade Element Theory(BET) analysis of the propeller. The ‘‘mass and the inertia" sub-model was designed utilizing the Raymer and DATCOM methodologies. A sub-model of an actuator using servomotor characteristics was employed to complete the model. The total model was then checked by validation of each submodel with numerical and experimental data. The results indicate that the obtained model was accurate and could be used to design a flight simulator.     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

WSO-UV project

During last three decades, astronomers have enjoyed continuous access to the 100–300 nm ultraviolet (UV) spectral range where the resonance transitions of the most abundant atoms and ions (at temperatures between 3000 and 300 000 K) reside. This UV range is not accessible from ground-based facilities. The successful International Ultraviolet Explorer (IUE) observatory, the Russian ASTRON mission and successor instruments such as the Galaxy Evolution Explorer (GALEX) mission or the COS and STIS spectrographs on-board the Hubble Space Telescope (HST) prove the major impact of observations in the UV wavelength range in modern astronomy. Future access to space-based observatories is expected to be very limited. For the next decade, the post-HST era, the World Space Observatory – Ultraviolet (WSO–UV) will be the only 2-m class UV telescope with capabilities similar to the HST. WSO–UV will be equipped with instruments for imaging and spectroscopy and it will be a facility dedicated, full-time, to UV astronomy. In this article, we briefly outline the current status of the WSO–UV mission and the science management plan.