CFRP层板的落重冲击分层损伤研究

采用落重冲击试验方法研究了航空上常用的铺层形式为［Ｏ２／９Ｏ２／４５２／－４５２］ｓ的先进复合材料（ＣＦＲＰ）低能冲击损伤问题。重点讨论了落重冲击后分层损伤形貌、冲击能量Ｗ与分层面积Ａ之间的关系以及基体韧性对ＣＦＲＰ抗冲击性能影响。     

固体火箭发动机寿命预估的一种考虑

利用弹性－粘弹性对应原理，分析长期贮存固体推进剂药柱由环境温度变化引起的热应力，计算药柱损伤，并对发动机寿命进行预估。理论分析和算法具有普遍性，可供工程设计参考。     

一个简易实用的疲劳损伤累积法则

1.法则的提出 利用材料的等幅疲劳试验数据进行承受变幅荷载的实际构件的疲劳设计,必须借助疲劳损伤累积理论。40年代以来,人们一直试图寻找一种较好的疲劳损伤累积理论。表1列举了其中的一些典型代表。     

单晶高温合金接近使用条件下的寿命估算与损伤分析

针对发动机热端部件承受的典型载荷谱，发展了一种通用的寿命预测方程和损伤分析方法。这个方法是在疲劳蠕变交互作用断裂特征图及其最大应力修正的寿命方程基础上建立的。根据ＤＤ３单晶合金的疲劳蠕变交互作用断裂特征图及其最大应力修正的寿命方程，验证了本方法是切实可行的。预测精度是符合要求的。     

无损检测的内涵演变及其在质量控制中的作用

就无损检测的内涵如何从探伤演变到评价及无损检测在质量控制中的应有作用作了叙述,希望对相关人员开拓思路、提高工作质量有所裨益.     

高能CO2激光腔镜高反介质薄膜的传输特性

为了获得适用于高能CO2激光器的高抗破坏阈值高反薄膜,以10.6μm高反膜ZnSe/YbF3,PbTe/BaF2膜系为例,数值模拟了激光在高反介质膜中的传输的场特性;给出了激光在多层介质膜中的场强分布、温度场分布及热应力分布。结果表明硅镜基体上的PbTe/BaF2膜系所需膜层厚度小、膜层数少,反射率可高达99.98%。     

Multi-mode optimal fuzzy active vibration control of composite beams laminated with photostrictive actuators

Firstly, a multi-field coupling finite element formulation of composited beam laminated with the photostrictive actuators is developed in this paper. Moreover, an optimal fuzzy active control algorithm is also proposed on the basis of the combination of optimal control and fuzzy one.This method opens a new avenue to resolve the contradiction between the linear system control method and nonlinear actuating characteristics of photostrictive actuators. The desired control for suppressing multi-modal vibration of photoelectric laminated beam is firstly obtained through optimal control and then the fuzzy control is used to approach the desired mechanical strain induced by photostrictive actuators. Thus, the multi-mode vibration control of beam is realized.In the design process of optimal fuzzy controller, the design of fuzzy control is independent of optimal control. The simulation results demonstrate that the proposed control method can effectively realize multi-modal vibration control of photoelectric laminated beams, and the control effect of optimal fuzzy control is better than that of optimal state feedback control.     

煤矿监测监控系统数据集成模式

从煤矿监测监控系统的实际出发,分析国内外煤矿监测监控系统的发展现状和局限性,论述用高新技术改造我国传统煤矿监测监控系统的可行性和必要性,然后从监测监控系统的结构角度,分析煤矿监控系统现阶段的发展主流和未来的发展趋势,并最终提出相应的信息数据集成技术方案。     

A general calculation method to specify center-of-buoyancy for the stratospheric airship with multiple gas cells

As the lighter-than-air (LTA) flight vehicle, the stratospheric airship is a desirable platform to provide communication and surveillance services. During the ascent from sea-level to the mission altitude, the volume of the lifting gas may change significantly, which will result in the change of the center-of-buoyancy (CB). A general calculation method is developed to specify CB for the stratospheric airship with a double-ellipsoid hull and an arbitrary number of the gas cells. The cross-section-integral (CSI) method is used as a basic calculation scenario to specify CB. Considering the complexity in determining the boundary between the helium and air in the gas cell, a searching algorithm is put forward and the specification of CB can be conducted by the iterative calculation. As an important application, the stable condition of the pitch angle is analyzed when the change of CB is involved. Under different initial configurations, the stable pitch angle of the stratospheric airship during the ascent is specified and compared, which shows the advantages of the multi-gas-cell configuration. The results of this paper may provide an important reference for the engineering application of the stratospheric airship.     

基于PAM-CRASH的蒙皮典型结构高速冲击仿真

以典型蒙皮结构为研究对象，分别对由2024－T3铝合金和碳纤维复合材料交替层压而成的FMLs以及2024－T3铝合金蒙皮进行高速冲击有限元仿真，并进行了损伤对比。其中，铝合金层和碳纤维层均采用最大应变准则。利用碰撞模拟分析软件PAM-CRASH以及采用SPH弹体对冲击模型进行仿真，结果显示在相同冲击能量下，加了支承结构的蒙皮在损伤抗性方面有了明显提升，并在此基础上分析不同的纤维铺层角度和铺层方式对FMLs蒙皮性能的影响。