电子束区熔定向凝固Nb基高温合金的组织和性能

研究了Nb-Si-Ti-Hf-Cr-Al-B-Y合金在电子束区熔炉上的定向凝固组织、室温断裂韧性和高温瞬时拉伸性能.合金的组织主要由Nb基固溶体(Nbss)、α-(Nb)5Si3和(Nb)3Si相组成.定向凝固后,初生Nbss枝晶以及Nbss α-(Nb)5Si3/(Nb)3Si层片状或棒状共晶团均沿着试棒轴线定向排列.当电子枪移动速率R=2.4 mm/min时,定向效果最好.定向凝固使合金在1250℃的拉伸强度及室温断裂韧性均显著提高.R=2.4 mm/min试棒的抗拉强度最高,达85.0 MPa,同时其室温断裂韧性也达到19.4 MPa·m1/2.     

机载脉冲多普勒雷达DBS技术

 本文从多普勒谱分辨理论出发,分析了DBS成象的基本原理,实现DBS成象的实时信号处理过程,提出了DBS实时数字信号处理方案。通过计算机模拟试验表明,在雷达天线保持匀速扫描状态时,系统的多普勒波束锐化比可达17.4:1左右,并可对载机前方±15°—60°方位范围内提供一幅大面积的,高分辨力的扇形雷达图象。     

Crashworthiness analysis of aircraft fuselage with sine-wave beam structure

An integrated design concept for crashworthy fuselage using sine-wave beam and strut is proposed and investigated. The finite element model of aircraft fuselage is built first. The structures above cabin floor, occupant and seat are simplified as two rigid blocks. The fuselage frame is redesigned, and the sine-wave beam is arranged under the frame. The impact dynamic performance of the aircraft with bottom sine-wave beam structure is studied and compared with that of conventional type. To obtain better crashworthiness performance, different rigidity of strut is combined with the sine-wave beam bottom structure. Numerical simulation result shows that the proposed sine-wave beam bottom structure could not only dissipate more proportion of impact kinetic energy but also reduce the initial peak acceleration. The structure and rigidity of strut have great influence on the crashworthiness performance. To give a better fuselage structure, both of the strut and bottom structure should be properly integrated and designed.     

Invariant and energy analysis of an axially retracting beam

The mechanism of a retracting cantilevered beam has been investigated by the invariant and energy-based analysis. The time-varying parameter partial differential equation governing the transverse vibrations of a beam with retracting motion is derived based on the momentum theorem. The assumed-mode method is used to truncate the governing partial differential equation into a set of ordinary differential equations (ODEs) with time-dependent coefficients. It is found that if the order of truncation is not less than the order of the initial conditions, the assumed-mode method can yield accurate results. The energy transfers among assumed modes are discussed during retrac-tion. The total energy varying with time has been investigated by numerical and analytical methods, and the results have good agreement with each other. For the transverse vibrations of the axially retracting beam, the adiabatic invariant is derived by both the averaging method and the Bessel function method.     

定向能武器及其应用

介绍了未来战争中的一种重要武器———定向能武器,包括激光武器、粒子束武器和射频武器。概述了这三种武器的工作机理、主要特点并进行了相互比较,介绍了定向能武器的应用。     

基于地球引力变轨的日冕探测器轨道设计

研究了相对黄道面有一定倾角的探测器轨道设计的问题。以金星借力轨道设计为例,分析了轨道偏心率与轨道倾角增量之间的关系。根据C3匹配原理搜索了“地球-中间天体-地球”多天体交会的发射窗口。最后,设计了与地球轨道周期相等的三次地球借力轨道,该轨道倾角可以达到黄纬30°以上。理论分析及仿真结果表明:基于地球引力设计此类轨道时,应采用多天体交会方案,才能既保证地球逃逸能量低,又保证首次飞入地球影响球前轨道偏心率较大的双重指标;同时应采用多次地球借力方案,该方案具有每次借力后轨道偏心率逐渐减小的特点,当其减小到零时,再次借力后轨道倾角不会继续增加。     

可编程DBS信号处理机的设计

本文讨论机载前视雷达中可编程多普勒波束锐化(DBS)信号处理机的结构和实现方法。研究了应用DBS技术提高机载前视雷达方位角分辨力的机理。提出了用高速位片实现的,采用微程序控制的可编程DBS实时信号处理机的硬件结构。采用这种结构可使DBS信号处理机在2ms内实时地处理完一幅子图象,其系统的波束锐化比可达15∶1。     

ACTIVE VIBRATION CONTROL OF A CANTILEVER BEAM USING PIEZOELECTRIC SENSORS AND ACTUATORS

讨论了利用压电片作为传感器和驱动器对悬臂梁进行主动振动控制问题，针对模态频率差距较大的系统，提出了分组建模和控制的方法。使用滤波器消除观测溢出。文中还讨论了传感器／驱动器配置问题。实验结果验证了所述方法的有效性。     

激光焊接机大理石横梁的有限元分析

采用有限元分析方法,设计了激光焊接机大理石横梁,利用Solid Works建立了大理石横梁的三维实体模型,使用ANSYS有限元分析软件,分析大理石横梁的静动态特性,为横梁的设计提供了理论基础和有效方法,对高精度激光焊接机产品的研发具有指导意义。     

方位扫描SAR区域成像研究

研究在SAR区域成像中,通过天线波束方位扫描扩大成像区方位宽度的机理以及信号处理方法。首先描述天线波束扫描的几何关系,推导出为达到要求的成像分辨率以及成像区方位宽度所需的天线波束扫描角速度和扫描角度的计算公式。分析了成像区位置与载机航迹的几何关系。然后讨论方位扫描SAR区域成像信号处理方法,并给出系统点目标响应仿真结果。最后,用试飞实测数据成像做了验证。