转子系统挤压油膜阻尼器设计与动力特性

鉴于挤压油膜阻尼器(SFD)设计必须要同时考虑转子系统的动力学特性,提出了一种转子系统与挤压油膜阻尼器耦合设计方法,给出了详细的设计流程。对所设计的阻尼器进行了CFD数值模拟、油膜压力测量以及减振效果实验,结果证明所提出的设计方法是有效的。相比未采用阻尼器,采用阻尼器后转子系统两个转盘的振幅分别下降了46%和39%。通过实验还研究了不平衡量、支承刚度、供油压力和滑油温度对挤压油膜阻尼器减振效果的影响。结果表明,相比于不平衡量和支承刚度对减振效果的影响,供油压力和滑油温度的影响并不显著。进行挤压油膜阻尼器设计时,重点应该关注转子上的不平衡量大小和支承刚度。     

Cross-sectional deformation behavior of double-ridged rectangular tube with fillers in different stages of H-typed bending

The bent double-ridged rectangular tube (DRRT) with high forming quality is helpful to improve the microwave transmission accuracy. For reducing the cross-sectional deformation in the H-typed bending process, in addition to using rigid mandrel to support the inside of tube, ridge groove fillers are also added to restrict the deformation of ridge grooves. Because of the change of stress and strain state of bent tube in bending, rigid mandrel retracting and specially twice-springback stages, and the springback of fillers, the cross-sectional deformation of tube in each stage may be different. Therefore, based on the ABAQUS platform, the finite element models (FEM) for H-typed bending, mandrel retracting and twice-springback stages of H96 DRRT with fillers were established and validated. It is found that, for the height and width deformation of tube and spacing deformation of ridge grooves, retraction of mandrel can make the distribution of these deformations more uniform along the bending direction. The first springback can reduce these deformations significantly, which should be emphasized. But the second springback only increases them by less amount, which can be ignored. The smaller height deformation of ridge groove and filler can be neglected.     

高温高速气流总焓接触测试法对比分析

发动机尾焰、燃烧加热、电弧加热器等高温高速气流总焓测量存在较大误差,采用结构优化的质量吸入水冷焓探针,标定后的驻点热流和驻点压力探针(Fay-Riddell公式法)对高温高速气流总焓进行了对比测试。结果表明:焓值为2.5~5 MJ/kg时,焓探针的测试误差约为3.38%,采用Fay-Riddell公式法获得焓值的误差约为3%。焓探针与Fay-Riddell公式法平均偏差约为4.65%。在地面模拟试验时采用两种测焓方法确定测试精度,对减小高温高速气流测焓误差,提高试验模拟精度具有积极的作用。     

发动机唇口电热防冰系统性能仿真

采用三维耦合传热方法对发动机唇口电热防冰系统进行了多状态下的性能仿真,获得了唇口表面平衡温度及动态温升响应时间,以此评估防冰系统性能,并通过与冰风洞试验结果对比,对仿真过程进行了修正。研究表明:唇口表面加热区平衡温度均高于273.15 K,温升响应时间小于60 s,满足防冰需要,较为严酷的防冰状态点主要为飞行速度较大、环境温度较低的状态点;修正唇口材料导热系数后,仿真与试验结果吻合良好。研究结果能有效指导工程研制,对提高防除冰仿真分析结果的准确性提供了很好的借鉴。     

退化量有缺失的无失效小样本轴承可靠性评估

针对有试验性能退化量参数记录、且(或)有部分数据缺失情况的小样本无失效轴承试验问题,通过由Taylor和Thompson提出的数据模拟法实现补全样本退化量,结合Bootstrap自助法扩大样本量,再根据基于性能退化轨迹的补充信息方法来进行其可靠性评估。选取7组受试轴承的振动退化量,对比在完整数据和带有缺失数据情况下的分析结果,发现可合理利用原舍弃不合规试验的部分有效信息,使之增加可靠性评估的样本数,从而得到较不用这些数据更为准确的结果,且所得结果较用完整数据结果绝对值相差在01以内。对比由极大似然估计法和加权E-Bayes法分析试验寿命数据的结果,发现该方法所得评估结果更优,与试验实际相比误差在10%以内,对于提高评估精度及降低试验成本有积极的实际意义。     

Fluid structure interaction simulation of supersonic parachute inflation by an interface tracking method

An Arbitrary Lagrangian–Eulerian (ALE) approach with interface tracking is developed in this paper to simulate the supersonic parachute inflation. A two-way interaction between a nonlinear finite element method and a finite volume method is accomplished. In order to apply this interface tracking method to problems with instantaneous large deformation and self-contact, a new virtual structure contact method is proposed to leave room for the body-fitted mesh between the contact structural surfaces. In addition, the breakpoint due to the fluid mesh with negative volume is losslessly restarted by the conservative interpolation method. Based on this method, fluid and structural dynamic behaviors of a highly folded disk-gap-band parachute are obtained. Numerical results such as maximum Root Mean Square (RMS) drag, general canopy shape and the smallest canopy projected areas in the terminal descent state are in accordance with the wind tunnel test results. This analysis reveals the inflation law of the disk-gap-band parachute and provides a new numerical method for supersonic parachute design.     

Optimization and verification of free flight separation similarity law in high-speed wind tunnel

Based on the similarity of separation time, a similarity law optimization method for high-speed weapon delivery test is derived. The typical separation state under wind load is simulated by the numerical method. The real separation data of aircraft, separation data of previous test methods, separation data of ideal wind tunnel test of previous methods, and simulation data of the proposed optimization method are obtained. A comparison of the data shows that the method proposed can improve the performance of tracking. Similarity law optimization starts with the development of motion equations and dynamic equations in the windless state to address the problems of mismatching between vertical and horizontal displacement, and to address the problems of separation trajectory distortion caused by insufficient gravity acceleration of the scaling model of existing light model. The ejection velocity of the model is taken as a factor/vector, and is adjusted reasonably to compensate the linear displacement insufficiency caused by the insufficient vertical acceleration of the light model method, so as to ensure the matching of the vertical and horizontal displacement of the projectile, and to improve the consistency between the test results of high-speed projection and the actual separation trajectory. The optimized similarity law is applicable to many existing free-throwing modes of high-speed wind tunnels. The optimized similarity law is not affected by the ejection velocity and hanging mode of the projectile. The optimized similarity law is suitable not only for the launching of the buried ammunition compartment and external stores, but also for the test design of projectile launching and gravity separation.     

用于光波纳米推力器的颗粒供应技术和光聚积技术研究

为提高光波纳米推力器在轨应用的可行性,针对与其匹配的颗粒供应技术和光聚积技术进行研究。提出整个推进系统的设计思路,通过建立理论计算和数值计算模型,分析颗粒供应技术和光聚积技术的各项核心结构参数的设计方法。计算结果表明:颗粒供应装置的正负电极内径之比(W/D)会影响正负电荷产生的总量之比,在W/D=300/322附近时,正负电荷比例接近1:1。静电诱导电压为9 V,当中和通道长度大于37.5mm时,正负颗粒可以视为完全中和。光聚积设计思路可令聚积球对光能的利用率在32.8%左右。两种相关技术的装置与推力器在结构上能够对接、在性能上可以匹配,从理论上表明了两种支撑技术的可行性。     

空心气冷低压涡轮动叶气热耦合数值模拟

以空心气冷低压涡轮动叶为研究对象,采用高质量的流体域和固体域网格控制技术,带转捩模型的双方程SST湍流模型,开展了基于CFD方法的叶片气热耦合问题研究。获得了不同冷气流量比(分别为1.0%,1.38%,1.8%和2.2%)、温比(分别为2.1,2.25,2.3,2.4和2.5)和压比(分别为1.4,1.6和1.8)对叶片换热特性的影响规律,设计状态中截面按弧长平均的叶片壁面金属温度计算值较试验值偏小0.3%,气热耦合计算的叶片壁面温度分布与试验结果吻合良好,验证了气热强耦合计算方法的精度,为涡轮叶片温度场分析提供了一种有效的方法。     

双脉冲固体火箭发动机隔舱打开与破片运动过程模拟

相比传统固体火箭发动机,具有能量管理特性的双脉冲固体火箭发动机结构更为复杂,为了提高其工作可靠性,针对核心部件金属隔舱的破片运动过程开展了数值仿真与试验研究。首先基于LS-DYNA软件,分析中引入监测函数、逻辑开关函数和加载驱动函数,模拟燃气流对破片的连续作用力,计算得到了在不同时刻破片的空间分布规律、撞击点位置及发动机内部损伤情况,保证了破片运动过程的高保真还原。其次,为了验证仿真结果的准确性,进行了模拟二脉冲初始工况的热流试验,发现破片撞击位置及损伤程度的仿真结果与试验数据一致性较高,其中撞击位置的预示误差小于9%,试验结果充分验证了有限元模型的准确性。由此,建立了适用于双脉冲固体火箭发动机金属隔舱破片运动过程的分析模型,实现了破片撞击位置及损伤程度的高精度预示。